diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h
index 212af31dfb..c7c1ca027e 100644
--- a/config/examples/ADIMLab/Gantry v1/Configuration.h	
+++ b/config/examples/ADIMLab/Gantry v1/Configuration.h	
@@ -726,6 +726,11 @@
  */
 #define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
 
+//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#if ENABLED(LIMITED_MAX_FR_EDITING)
+  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Max Acceleration (change/s) change = mm/s
  * (Maximum start speed for accelerated moves)
@@ -734,6 +739,11 @@
  */
 #define DEFAULT_MAX_ACCELERATION      { 2000, 2000, 50, 2000 }
 
+//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
+  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Acceleration (change/s) change = mm/s
  * Override with M204
@@ -759,6 +769,11 @@
   #define DEFAULT_XJERK 20.0
   #define DEFAULT_YJERK 20.0
   #define DEFAULT_ZJERK  0.4
+
+  //#define LIMITED_JERK_EDITING        // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
+  #if ENABLED(LIMITED_JERK_EDITING)
+    #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
+  #endif
 #endif
 
 #define DEFAULT_EJERK    5.0  // May be used by Linear Advance
diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
index b5d0f7cb78..b11172ab04 100644
--- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
+++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
@@ -972,9 +972,6 @@
     // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
     // especially with "vase mode" printing. Set too high and vases cannot be continued.
     #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
-
-    //#define DEBUG_POWER_LOSS_RECOVERY // Debug informations on serial output
-    //#define SAVE_INFO_INTERVAL_MS 0   // Force SD recov. write interval, on each layer start if 0
   #endif
 
   /**
diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h
index da18ae8971..c8ad999d61 100644
--- a/config/examples/Alfawise/U20/Configuration_adv.h
+++ b/config/examples/Alfawise/U20/Configuration_adv.h
@@ -971,9 +971,6 @@
     // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
     // especially with "vase mode" printing. Set too high and vases cannot be continued.
     #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
-
-    //#define DEBUG_POWER_LOSS_RECOVERY // Debug informations on serial output
-    //#define SAVE_INFO_INTERVAL_MS 0   // Force SD recov. write interval, on each layer start if 0
   #endif
 
   /**
diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h
index c16fb220a4..768f59b37a 100644
--- a/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/config/examples/BQ/Hephestos_2/Configuration.h
@@ -1105,6 +1105,7 @@
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
+  //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 
   // Set one or more commands to execute on filament runout.
   // (After 'M412 H' Marlin will ask the host to handle the process.)
diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h
index 8fa02dbbe5..cbe692312d 100644
--- a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h	
+++ b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h	
@@ -960,6 +960,8 @@
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
+    //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h
index 20941352e3..9e5a2505e2 100644
--- a/config/examples/Creality/CR-20 Pro/Configuration.h	
+++ b/config/examples/Creality/CR-20 Pro/Configuration.h	
@@ -877,12 +877,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h
index d047641ded..e846aabb2d 100644
--- a/config/examples/Creality/CR-20/Configuration.h
+++ b/config/examples/Creality/CR-20/Configuration.h
@@ -877,12 +877,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
diff --git a/config/examples/Creality/Ender-5/Configuration.h b/config/examples/Creality/Ender-5/Configuration.h
index 87baa4509f..dedbb1078b 100644
--- a/config/examples/Creality/Ender-5/Configuration.h
+++ b/config/examples/Creality/Ender-5/Configuration.h
@@ -877,12 +877,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h
index 8e9f6fd121..78bf6b54bf 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration.h
@@ -1275,6 +1275,8 @@
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
+  #define LEVEL_CORNERS_HEIGHT 0.0  // (mm) Z height of nozzle at leveling points
   //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h
index eac0d34567..3ab063571e 100644
--- a/config/examples/Formbot/Raptor/Configuration.h
+++ b/config/examples/Formbot/Raptor/Configuration.h
@@ -482,6 +482,7 @@
 #define HEATER_2_MINTEMP   5
 #define HEATER_3_MINTEMP   5
 #define HEATER_4_MINTEMP   5
+#define HEATER_5_MINTEMP   5
 #define BED_MINTEMP        5
 
 // Above this temperature the heater will be switched off.
@@ -492,6 +493,7 @@
 #define HEATER_2_MAXTEMP 275
 #define HEATER_3_MAXTEMP 275
 #define HEATER_4_MAXTEMP 275
+#define HEATER_5_MAXTEMP 275
 #if ENABLED(BED_AC)
   #define BED_MAXTEMP    150
 #else
@@ -1004,6 +1006,8 @@
  * Specify a Probe position as { X, Y, Z }
  */
 #define NOZZLE_TO_PROBE_OFFSET { -22, 0, -1.5 }
+
+// Certain types of probes need to stay away from edges
 #define MIN_PROBE_EDGE 10
 
 // X and Y axis travel speed (mm/m) between probes
@@ -1314,9 +1318,6 @@
   #define GRID_MAX_POINTS_X 6
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
-  // The Z probe minimum outer margin (to validate G29 parameters).
-  #define MIN_PROBE_EDGE 10
-
   // Probe along the Y axis, advancing X after each column
   //#define PROBE_Y_FIRST
 
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
index 9bae1d51e2..31142284d7 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
@@ -909,7 +909,19 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
-#if HAS_PRINT_PROGRESS
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
+#if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion
+  #if ENABLED(SHOW_REMAINING_TIME)
+    //#define USE_M73_REMAINING_TIME     // Use remaining time from M73 command instead of estimation
+    //#define ROTATE_PROGRESS_DISPLAY    // Display (P)rogress, (E)lapsed, and (R)emaining time
+  #endif
+#endif
+
+#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)
     #define PROGRESS_BAR_BAR_TIME 2000    // (ms) Amount of time to show the bar
diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
index a5b6c76cf7..c1974957cf 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
@@ -938,7 +938,7 @@
   #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
-  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
 
   // Reverse SD sort to show "more recent" files first, according to the card's FAT.
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h
index 6a837f602b..450dddc1a2 100644
--- a/config/examples/HMS434/Configuration.h
+++ b/config/examples/HMS434/Configuration.h
@@ -447,6 +447,8 @@
 #define HEATER_1_MAXTEMP 410
 #define HEATER_2_MAXTEMP 410
 #define HEATER_3_MAXTEMP 410
+#define HEATER_4_MAXTEMP 410
+#define HEATER_5_MAXTEMP 410
 #define BED_MAXTEMP      150
 
 //===========================================================================
@@ -2013,6 +2015,12 @@
 //
 //#define MALYAN_LCD
 
+//
+// LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays
+// See Configuration_adv.h for all configuration options.
+//
+//#define LULZBOT_TOUCH_UI
+
 //
 // Third-party or vendor-customized controller interfaces.
 // Sources should be installed in 'src/lcd/extensible_ui'.
diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h
index 6d50f426bf..bd43e29901 100644
--- a/config/examples/HMS434/Configuration_adv.h
+++ b/config/examples/HMS434/Configuration_adv.h
@@ -655,8 +655,8 @@
 
 //#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
-// minimum time in microseconds that a movement needs to take if the buffer is emptied.
-#define DEFAULT_MINSEGMENTTIME        20000
+// Minimum time that a segment needs to take if the buffer is emptied
+#define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
 // If defined the movements slow down when the look ahead buffer is only half full
 #define SLOWDOWN
@@ -855,11 +855,35 @@
   #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
 #endif
 
-// Include a page of printer information in the LCD Main Menu
-//#define LCD_INFO_MENU
-#if ENABLED(LCD_INFO_MENU)
-  //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
-#endif
+#if HAS_LCD_MENU
+
+  // Include a page of printer information in the LCD Main Menu
+  //#define LCD_INFO_MENU
+  #if ENABLED(LCD_INFO_MENU)
+    //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
+  #endif
+
+  // BACK menu items keep the highlight at the top
+  //#define TURBO_BACK_MENU_ITEM
+
+  /**
+   * LED Control Menu
+   * Add LED Control to the LCD menu
+   */
+  //#define LED_CONTROL_MENU
+  #if ENABLED(LED_CONTROL_MENU)
+    #define LED_COLOR_PRESETS                 // Enable the Preset Color menu option
+    #if ENABLED(LED_COLOR_PRESETS)
+      #define LED_USER_PRESET_RED        255  // User defined RED value
+      #define LED_USER_PRESET_GREEN      128  // User defined GREEN value
+      #define LED_USER_PRESET_BLUE         0  // User defined BLUE value
+      #define LED_USER_PRESET_WHITE      255  // User defined WHITE value
+      #define LED_USER_PRESET_BRIGHTNESS 255  // User defined intensity
+      //#define LED_USER_PRESET_STARTUP       // Have the printer display the user preset color on startup
+    #endif
+  #endif
+
+#endif // HAS_LCD_MENU
 
 // Scroll a longer status message into view
 //#define STATUS_MESSAGE_SCROLLING
@@ -896,23 +920,6 @@
   #endif
 #endif
 
-/**
- * LED Control Menu
- * Enable this feature to add LED Control to the LCD menu
- */
-//#define LED_CONTROL_MENU
-#if ENABLED(LED_CONTROL_MENU)
-  #define LED_COLOR_PRESETS                 // Enable the Preset Color menu option
-  #if ENABLED(LED_COLOR_PRESETS)
-    #define LED_USER_PRESET_RED        255  // User defined RED value
-    #define LED_USER_PRESET_GREEN      128  // User defined GREEN value
-    #define LED_USER_PRESET_BLUE         0  // User defined BLUE value
-    #define LED_USER_PRESET_WHITE      255  // User defined WHITE value
-    #define LED_USER_PRESET_BRIGHTNESS 255  // User defined intensity
-    //#define LED_USER_PRESET_STARTUP       // Have the printer display the user preset color on startup
-  #endif
-#endif // LED_CONTROL_MENU
-
 #if ENABLED(SDSUPPORT)
 
   // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
@@ -949,6 +956,7 @@
     //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
+    //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
 
@@ -1167,6 +1175,7 @@
   //#define STATUS_FAN_FRAMES 3       // :[0,1,2,3,4] Number of fan animation frames
   //#define STATUS_HEAT_PERCENT       // Show heating in a progress bar
   //#define BOOT_MARLIN_LOGO_SMALL    // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
+  //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
 
   // Frivolous Game Options
   //#define MARLIN_BRICKOUT
@@ -1244,8 +1253,12 @@
   // Use a smaller font when labels don't fit buttons
   #define TOUCH_UI_FIT_TEXT
 
-  // Runtime language selection (otherwise LCD_LANGUAGE)
-  //#define TOUCH_UI_LANGUAGE_MENU
+  // Allow language selection from menu at run-time (otherwise use LCD_LANGUAGE)
+  //#define LCD_LANGUAGE_1 en
+  //#define LCD_LANGUAGE_2 fr
+  //#define LCD_LANGUAGE_3 de
+  //#define LCD_LANGUAGE_4 es
+  //#define LCD_LANGUAGE_5 it
 
   // Use a numeric passcode for "Screen lock" keypad.
   // (recommended for smaller displays)
@@ -2433,6 +2446,13 @@
  */
 #define EXTENDED_CAPABILITIES_REPORT
 
+/**
+ * Expected Printer Check
+ * Add the M16 G-code to compare a string to the MACHINE_NAME.
+ * M16 with a non-matching string causes the printer to halt.
+ */
+//#define EXPECTED_PRINTER_CHECK
+
 /**
  * Disable all Volumetric extrusion options
  */
@@ -2487,6 +2507,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h
index d0229c5175..f9ce4432b5 100644
--- a/config/examples/JGAurora/A1/Configuration.h
+++ b/config/examples/JGAurora/A1/Configuration.h
@@ -733,6 +733,11 @@
  */
 #define DEFAULT_MAX_FEEDRATE          { 360, 150, 30, 40 }
 
+//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#if ENABLED(LIMITED_MAX_FR_EDITING)
+  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Max Acceleration (change/s) change = mm/s
  * (Maximum start speed for accelerated moves)
@@ -741,6 +746,11 @@
  */
 #define DEFAULT_MAX_ACCELERATION      { 1200, 350, 100, 500 }
 
+//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
+  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Acceleration (change/s) change = mm/s
  * Override with M204
@@ -766,6 +776,11 @@
   #define DEFAULT_XJERK 13.0
   #define DEFAULT_YJERK 5.0
   #define DEFAULT_ZJERK  0.4
+
+  //#define LIMITED_JERK_EDITING        // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
+  #if ENABLED(LIMITED_JERK_EDITING)
+    #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
+  #endif
 #endif
 
 #define DEFAULT_EJERK    5.0  // May be used by Linear Advance
diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h
index 87f9702b6e..2156e6b34c 100644
--- a/config/examples/JGAurora/A5S/Configuration.h
+++ b/config/examples/JGAurora/A5S/Configuration.h
@@ -733,6 +733,11 @@
  */
 #define DEFAULT_MAX_FEEDRATE          { 360, 150, 30, 40 }
 
+//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#if ENABLED(LIMITED_MAX_FR_EDITING)
+  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Max Acceleration (change/s) change = mm/s
  * (Maximum start speed for accelerated moves)
@@ -741,6 +746,11 @@
  */
 #define DEFAULT_MAX_ACCELERATION      { 1200, 350, 100, 500 }
 
+//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
+  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Acceleration (change/s) change = mm/s
  * Override with M204
@@ -766,6 +776,11 @@
   #define DEFAULT_XJERK 13.0
   #define DEFAULT_YJERK 5.0
   #define DEFAULT_ZJERK  0.4
+
+  //#define LIMITED_JERK_EDITING        // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
+  #if ENABLED(LIMITED_JERK_EDITING)
+    #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
+  #endif
 #endif
 
 #define DEFAULT_EJERK    5.0  // May be used by Linear Advance
diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h
index a0c4259341..1cfc5e99bd 100644
--- a/config/examples/MakerParts/Configuration_adv.h
+++ b/config/examples/MakerParts/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
@@ -2512,6 +2515,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h
index 6cc2eadfae..d910f76f0a 100644
--- a/config/examples/Malyan/M150/Configuration_adv.h
+++ b/config/examples/Malyan/M150/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h
index a84ffab9b7..5c1744ecda 100644
--- a/config/examples/Malyan/M200/Configuration_adv.h
+++ b/config/examples/Malyan/M200/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index c8209f8d86..f6951d88c0 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h
index 5d3152e633..3d85e75416 100644
--- a/config/examples/Mks/Robin/Configuration_adv.h
+++ b/config/examples/Mks/Robin/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h
index 616511ebcc..cc3544fdca 100644
--- a/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/config/examples/Mks/Sbase/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h
index 322fc87231..31d2e63267 100644
--- a/config/examples/RapideLite/RL200/Configuration_adv.h
+++ b/config/examples/RapideLite/RL200/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h
index 40d88dd6a5..2ff7614bc1 100644
--- a/config/examples/RigidBot/Configuration_adv.h
+++ b/config/examples/RigidBot/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
index f88043c886..035bd2ac03 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h
index b85ebeff4e..b059be0dfb 100644
--- a/config/examples/Sanguinololu/Configuration_adv.h
+++ b/config/examples/Sanguinololu/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h
index 88ca1c074d..8eede1a013 100644
--- a/config/examples/Tevo/Michelangelo/Configuration_adv.h
+++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 #define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h
index deaf7d621f..b7f7ccff81 100644
--- a/config/examples/Tevo/Tarantula Pro/Configuration.h	
+++ b/config/examples/Tevo/Tarantula Pro/Configuration.h	
@@ -939,10 +939,17 @@
 // Feedrate (mm/m) for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
 
-// The number of probes to perform at each point.
-//   Set to 2 for a fast/slow probe, using the second probe result.
-//   Set to 3 or more for slow probes, averaging the results.
+/**
+ * Multiple Probing
+ *
+ * You may get improved results by probing 2 or more times.
+ * With EXTRA_PROBING the more atypical reading(s) will be disregarded.
+ *
+ * A total of 2 does fast/slow probes with a weighted average.
+ * A total of 3 or more adds more slow probes, taking the average.
+ */
 //#define MULTIPLE_PROBING 2
+//#define EXTRA_PROBING    1
 
 /**
  * Z probes require clearance when deploying, stowing, and moving between
diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h
index 26f5d8a06b..0dfe1a9615 100755
--- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h	
+++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h	
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 #define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h
index 05950a4c9e..7cc8221b8e 100644
--- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h	
+++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h	
@@ -731,6 +731,11 @@
  */
 #define DEFAULT_MAX_FEEDRATE          { 250, 250, 30, 55 }
 
+//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#if ENABLED(LIMITED_MAX_FR_EDITING)
+  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Max Acceleration (change/s) change = mm/s
  * (Maximum start speed for accelerated moves)
@@ -739,6 +744,11 @@
  */
 #define DEFAULT_MAX_ACCELERATION      { 2000, 2000, 120, 10000 }
 
+//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
+  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Acceleration (change/s) change = mm/s
  * Override with M204
@@ -764,6 +774,11 @@
   #define DEFAULT_XJERK  8.0
   #define DEFAULT_YJERK  8.0
   #define DEFAULT_ZJERK  0.4
+
+  //#define LIMITED_JERK_EDITING        // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
+  #if ENABLED(LIMITED_JERK_EDITING)
+    #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
+  #endif
 #endif
 
 #define DEFAULT_EJERK    5.0  // May be used by Linear Advance
diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
index c8a85545fc..92857c0897 100755
--- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h	
+++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h	
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 #define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h
index 03ce1d53f6..d267a6b260 100644
--- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h	
+++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h	
@@ -731,6 +731,11 @@
  */
 #define DEFAULT_MAX_FEEDRATE          { 250, 250, 30, 55 }
 
+//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#if ENABLED(LIMITED_MAX_FR_EDITING)
+  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Max Acceleration (change/s) change = mm/s
  * (Maximum start speed for accelerated moves)
@@ -739,6 +744,11 @@
  */
 #define DEFAULT_MAX_ACCELERATION      { 2000, 2000, 120, 10000 }
 
+//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
+  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Acceleration (change/s) change = mm/s
  * Override with M204
@@ -764,6 +774,11 @@
   #define DEFAULT_XJERK  8.0
   #define DEFAULT_YJERK  8.0
   #define DEFAULT_ZJERK  0.4
+
+  //#define LIMITED_JERK_EDITING        // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
+  #if ENABLED(LIMITED_JERK_EDITING)
+    #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
+  #endif
 #endif
 
 #define DEFAULT_EJERK    5.0  // May be used by Linear Advance
diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
index c8a85545fc..92857c0897 100755
--- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h	
+++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h	
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 #define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h
index 8ac80ffefe..bde0e0a4a1 100644
--- a/config/examples/TheBorg/Configuration_adv.h
+++ b/config/examples/TheBorg/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h
index 69835e01cc..1b317ad38c 100644
--- a/config/examples/TinyBoy2/Configuration_adv.h
+++ b/config/examples/TinyBoy2/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h
index 55a99620f0..ad6ab070f4 100644
--- a/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/config/examples/Tronxy/X3A/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
index d23a8696dc..bb204fbecd 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h
index 17357f5b57..183452143a 100644
--- a/config/examples/UltiMachine/Archim1/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h
index 1949aa6374..808e93caf4 100644
--- a/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h
index 9b6fff1722..2badc8b686 100644
--- a/config/examples/VORONDesign/Configuration_adv.h
+++ b/config/examples/VORONDesign/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h
index 8ee236273c..55f847dc15 100644
--- a/config/examples/Velleman/K8200/Configuration.h
+++ b/config/examples/Velleman/K8200/Configuration.h
@@ -2005,6 +2005,43 @@
 
 #endif // K8200_VM8201
 
+//=============================================================================
+//==============================  OLED Displays  ==============================
+//=============================================================================
+
+//
+// SSD1306 OLED full graphics generic display
+//
+//#define U8GLIB_SSD1306
+
+//
+// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
+//
+//#define SAV_3DGLCD
+#if ENABLED(SAV_3DGLCD)
+  #define U8GLIB_SSD1306
+  //#define U8GLIB_SH1106
+#endif
+
+//
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
+// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
+// http://reprap.org/wiki/MKS_12864OLED
+//
+// Tiny, but very sharp OLED display
+//
+//#define MKS_12864OLED          // Uses the SH1106 controller (default)
+//#define MKS_12864OLED_SSD1306  // Uses the SSD1306 controller
+
+//
+// Einstart S OLED SSD1306
+//
+//#define U8GLIB_SH1106_EINSTART
+
 //
 // Overlord OLED display/controller with i2c buzzer and LEDs
 //
diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h
index fd2f8a5219..ba7dff2c6d 100644
--- a/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/config/examples/Velleman/K8200/Configuration_adv.h
@@ -303,6 +303,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 #define FAN_KICKSTART_TIME 500
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
index 9d2a94a28d..a0b391245a 100644
--- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
index 9d2a94a28d..a0b391245a 100644
--- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h
index f199cfa283..edfabbcd85 100644
--- a/config/examples/WASP/PowerWASP/Configuration_adv.h
+++ b/config/examples/WASP/PowerWASP/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index 5a10579859..ac35b5e8c8 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
+++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h
index 53e8949cd4..eba602b51a 100644
--- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h	
+++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h	
@@ -737,6 +737,11 @@
  */
 #define DEFAULT_MAX_FEEDRATE          { 700, 700, 100, 10000 }
 
+//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#if ENABLED(LIMITED_MAX_FR_EDITING)
+  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Max Acceleration (change/s) change = mm/s
  * (Maximum start speed for accelerated moves)
@@ -745,6 +750,11 @@
  */
 #define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
 
+//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
+  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Acceleration (change/s) change = mm/s
  * Override with M204
@@ -903,11 +913,10 @@
 
 /**
  * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- * X and Y offsets must be integers.
  *
  * In the following example the X and Y offsets are both positive:
- * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *   #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  *
  *     +-- BACK ---+
  *     |           |
@@ -919,10 +928,10 @@
  *     |           |
  *     O-- FRONT --+
  *   (0,0)
+ *
+ * Specify a Probe position as { X, Y, Z }
  */
-#define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
-#define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]
-#define Z_PROBE_OFFSET_FROM_EXTRUDER 0   // Z offset: -below +above  [the nozzle]
+#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
 
 // Certain types of probes need to stay away from edges
 #define MIN_PROBE_EDGE 10
@@ -956,7 +965,7 @@
  *
  * Use these settings to specify the distance (mm) to raise the probe (or
  * lower the bed). The values set here apply over and above any (negative)
- * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
+ * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
  * Only integer values >= 1 are valid here.
  *
  * Example: `M851 Z-5` with a CLEARANCE of 4  =>  9mm from bed to nozzle.
@@ -1214,12 +1223,6 @@
   #define GRID_MAX_POINTS_X 3
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
-  // Set the boundaries for probing (where the probe can reach).
-  //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
-  //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
-  //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
-  //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
-
   // Probe along the Y axis, advancing X after each column
   //#define PROBE_Y_FIRST
 
@@ -1273,19 +1276,6 @@
 
 #endif // BED_LEVELING
 
-/**
- * Points to probe for all 3-point Leveling procedures.
- * Override if the automatically selected points are inadequate.
- */
-#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
-  //#define PROBE_PT_1_X 15
-  //#define PROBE_PT_1_Y 180
-  //#define PROBE_PT_2_X 15
-  //#define PROBE_PT_2_Y 20
-  //#define PROBE_PT_3_X 170
-  //#define PROBE_PT_3_Y 20
-#endif
-
 /**
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
@@ -1593,10 +1583,10 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *   en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, jp-kana,
- *   ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
+ *   en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, it, jp_kana,
+ *   ko_KR, nl, pl, pt, pt_br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 
diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h
index 19f4773df0..359b3d27ed 100644
--- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h	
+++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h	
@@ -214,7 +214,7 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-// Show extra position information in M114
+// Show extra position information with 'M114 D'
 //#define M114_DETAIL
 
 // Show Temperature ADC value
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
@@ -379,6 +382,7 @@
   #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
   #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
   #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define CASE_LIGHT_MAX_PWM 128            // Limit pwm
   //#define CASE_LIGHT_MENU                   // Add Case Light options to the LCD menu
   //#define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
   //#define CASE_LIGHT_USE_NEOPIXEL           // Use Neopixel LED as case light, requires NEOPIXEL_LED.
@@ -901,6 +905,18 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
+#if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion
+  #if ENABLED(SHOW_REMAINING_TIME)
+    //#define USE_M73_REMAINING_TIME     // Use remaining time from M73 command instead of estimation
+    //#define ROTATE_PROGRESS_DISPLAY    // Display (P)rogress, (E)lapsed, and (R)emaining time
+  #endif
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)
@@ -1219,21 +1235,48 @@
   //#define TOUCH_UI_PORTRAIT
   //#define TOUCH_UI_MIRRORED
 
-  // Enable UTF8 rendering capabilities.
+  // UTF8 processing and rendering.
+  // Unsupported characters are shown as '?'.
   //#define TOUCH_UI_USE_UTF8
   #if ENABLED(TOUCH_UI_USE_UTF8)
+    // Western accents support. These accented characters use
+    // combined bitmaps and require relatively little storage.
     #define TOUCH_UI_UTF8_WESTERN_CHARSET
+    #if ENABLED(TOUCH_UI_UTF8_WESTERN_CHARSET)
+      // Additional character groups. These characters require
+      // full bitmaps and take up considerable storage:
+      //#define TOUCH_UI_UTF8_SUPERSCRIPTS  // ¹ ² ³
+      //#define TOUCH_UI_UTF8_COPYRIGHT     // © ®
+      //#define TOUCH_UI_UTF8_GERMANIC      // ß
+      //#define TOUCH_UI_UTF8_SCANDINAVIAN  // Æ Ð Ø Þ æ ð ø þ
+      //#define TOUCH_UI_UTF8_PUNCTUATION   // « » ¿ ¡
+      //#define TOUCH_UI_UTF8_CURRENCY      // ¢ £ ¤ ¥
+      //#define TOUCH_UI_UTF8_ORDINALS      // º ª
+      //#define TOUCH_UI_UTF8_MATHEMATICS   // ± × ÷
+      //#define TOUCH_UI_UTF8_FRACTIONS     // ¼ ½ ¾
+      //#define TOUCH_UI_UTF8_SYMBOLS       // µ ¶ ¦ § ¬
+    #endif
   #endif
 
-  // When labels do not fit buttons, use smaller font
+  // Use a smaller font when labels don't fit buttons
   #define TOUCH_UI_FIT_TEXT
 
-  // Runtime language selection (otherwise LCD_LANGUAGE)
-  //#define TOUCH_UI_LANGUAGE_MENU
+  // Allow language selection from menu at run-time (otherwise use LCD_LANGUAGE)
+  //#define LCD_LANGUAGE_1 en
+  //#define LCD_LANGUAGE_2 fr
+  //#define LCD_LANGUAGE_3 de
+  //#define LCD_LANGUAGE_4 es
+  //#define LCD_LANGUAGE_5 it
 
   // Use a numeric passcode for "Screen lock" keypad.
   // (recommended for smaller displays)
   //#define TOUCH_UI_PASSCODE
+
+  // Output extra debug info for Touch UI events
+  //#define TOUCH_UI_DEBUG
+
+  // Developer menu (accessed by touching "About Printer" copyright text)
+  //#define TOUCH_UI_DEVELOPER_MENU
 #endif
 
 //
@@ -1328,6 +1371,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ *
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ *
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET
@@ -2074,7 +2153,7 @@
     #define X_OVERCURRENT   2000  // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down)
     #define X_STALLCURRENT  1500  // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) -  4A max - rounds down)
     #define X_MAX_VOLTAGE    127  // 0-255, Maximum effective voltage seen by stepper
-    #define X_CHAIN_POS        0  // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI
+    #define X_CHAIN_POS       -1  // Position in SPI chain. (<=0 : Not in chain. 1 : Nearest MOSI)
   #endif
 
   #if AXIS_DRIVER_TYPE_X2(L6470)
@@ -2082,7 +2161,7 @@
     #define X2_OVERCURRENT    2000
     #define X2_STALLCURRENT   1500
     #define X2_MAX_VOLTAGE     127
-    #define X2_CHAIN_POS         0
+    #define X2_CHAIN_POS        -1
   #endif
 
   #if AXIS_DRIVER_TYPE_Y(L6470)
@@ -2090,7 +2169,7 @@
     #define Y_OVERCURRENT     2000
     #define Y_STALLCURRENT    1500
     #define Y_MAX_VOLTAGE      127
-    #define Y_CHAIN_POS          0
+    #define Y_CHAIN_POS         -1
   #endif
 
   #if AXIS_DRIVER_TYPE_Y2(L6470)
@@ -2098,7 +2177,7 @@
     #define Y2_OVERCURRENT    2000
     #define Y2_STALLCURRENT   1500
     #define Y2_MAX_VOLTAGE     127
-    #define Y2_CHAIN_POS         0
+    #define Y2_CHAIN_POS        -1
   #endif
 
   #if AXIS_DRIVER_TYPE_Z(L6470)
@@ -2106,7 +2185,7 @@
     #define Z_OVERCURRENT     2000
     #define Z_STALLCURRENT    1500
     #define Z_MAX_VOLTAGE      127
-    #define Z_CHAIN_POS          0
+    #define Z_CHAIN_POS         -1
   #endif
 
   #if AXIS_DRIVER_TYPE_Z2(L6470)
@@ -2114,7 +2193,7 @@
     #define Z2_OVERCURRENT    2000
     #define Z2_STALLCURRENT   1500
     #define Z2_MAX_VOLTAGE     127
-    #define Z2_CHAIN_POS         0
+    #define Z2_CHAIN_POS        -1
   #endif
 
   #if AXIS_DRIVER_TYPE_Z3(L6470)
@@ -2122,7 +2201,7 @@
     #define Z3_OVERCURRENT    2000
     #define Z3_STALLCURRENT   1500
     #define Z3_MAX_VOLTAGE     127
-    #define Z3_CHAIN_POS         0
+    #define Z3_CHAIN_POS        -1
   #endif
 
   #if AXIS_DRIVER_TYPE_E0(L6470)
@@ -2130,7 +2209,7 @@
     #define E0_OVERCURRENT    2000
     #define E0_STALLCURRENT   1500
     #define E0_MAX_VOLTAGE     127
-    #define E0_CHAIN_POS         0
+    #define E0_CHAIN_POS        -1
   #endif
 
   #if AXIS_DRIVER_TYPE_E1(L6470)
@@ -2138,7 +2217,7 @@
     #define E1_OVERCURRENT    2000
     #define E1_STALLCURRENT   1500
     #define E1_MAX_VOLTAGE     127
-    #define E1_CHAIN_POS         0
+    #define E1_CHAIN_POS        -1
   #endif
 
   #if AXIS_DRIVER_TYPE_E2(L6470)
@@ -2146,7 +2225,7 @@
     #define E2_OVERCURRENT    2000
     #define E2_STALLCURRENT   1500
     #define E2_MAX_VOLTAGE     127
-    #define E2_CHAIN_POS         0
+    #define E2_CHAIN_POS        -1
   #endif
 
   #if AXIS_DRIVER_TYPE_E3(L6470)
@@ -2154,7 +2233,7 @@
     #define E3_OVERCURRENT    2000
     #define E3_STALLCURRENT   1500
     #define E3_MAX_VOLTAGE     127
-    #define E3_CHAIN_POS         0
+    #define E3_CHAIN_POS        -1
   #endif
 
   #if AXIS_DRIVER_TYPE_E4(L6470)
@@ -2162,7 +2241,7 @@
     #define E4_OVERCURRENT    2000
     #define E4_STALLCURRENT   1500
     #define E4_MAX_VOLTAGE     127
-    #define E4_CHAIN_POS         0
+    #define E4_CHAIN_POS        -1
   #endif
 
   #if AXIS_DRIVER_TYPE_E5(L6470)
@@ -2170,7 +2249,7 @@
     #define E5_OVERCURRENT    2000
     #define E5_STALLCURRENT   1500
     #define E5_MAX_VOLTAGE     127
-    #define E5_CHAIN_POS         0
+    #define E5_CHAIN_POS        -1
   #endif
 
   /**
diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
index 32859dcc5d..c624c92fa7 100644
--- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h	
+++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h	
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h
index f4e05e3f96..4e7449bfa5 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -1147,6 +1147,9 @@
 
 // Before deploy/stow pause for user confirmation
 #define PAUSE_BEFORE_DEPLOY_STOW
+#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
+  //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
+#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h
index 2d13e92971..32f8b302f2 100644
--- a/config/examples/delta/Dreammaker/Overlord/Configuration.h
+++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h
@@ -805,6 +805,11 @@
  */
 #define DEFAULT_MAX_FEEDRATE          { 100, 100, 100, 25 }
 
+//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#if ENABLED(LIMITED_MAX_FR_EDITING)
+  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Max Acceleration (change/s) change = mm/s
  * (Maximum start speed for accelerated moves)
@@ -813,6 +818,11 @@
  */
 #define DEFAULT_MAX_ACCELERATION      { 1000, 1000, 1000, 3000 }
 
+//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
+  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Acceleration (change/s) change = mm/s
  * Override with M204
@@ -838,6 +848,11 @@
   #define DEFAULT_XJERK 10.0
   #define DEFAULT_YJERK DEFAULT_XJERK
   #define DEFAULT_ZJERK DEFAULT_XJERK // Must be same as XY for delta
+
+  //#define LIMITED_JERK_EDITING        // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
+  #if ENABLED(LIMITED_JERK_EDITING)
+    #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
+  #endif
 #endif
 
 #define DEFAULT_EJERK    5.0  // May be used by Linear Advance
diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
index 50d84f2bca..ad0182c874 100644
--- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
+++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
@@ -2058,17 +2058,27 @@
   #define E5_HYBRID_THRESHOLD     30
 
   /**
+   * Use StallGuard2 to home / probe X, Y, Z.
+   *
    * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
-   * Use StallGuard2 to sense an obstacle and trigger an endstop.
    * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
    * X, Y, and Z homing will always be done in spreadCycle mode.
    *
-   * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
-   * Higher values make the system LESS sensitive.
-   * Lower value make the system MORE sensitive.
-   * Too low values can lead to false positives, while too high values will collide the axis without triggering.
-   * It is advised to set X/Y/Z_HOME_BUMP_MM to 0.
-   * M914 X/Y/Z to live tune the setting
+   * X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
+   * Use M914 X Y Z to set the stall threshold at runtime:
+   *
+   *  Sensitivity   TMC2209   Others
+   *    HIGHEST       255      -64    (Too sensitive => False positive)
+   *    LOWEST         0        63    (Too insensitive => No trigger)
+   *
+   * It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
+   *
+   * SPI_ENDSTOPS  *** Beta feature! *** TMC2130 Only ***
+   * Poll the driver through SPI to determine load when homing.
+   * Removes the need for a wire from DIAG1 to an endstop pin.
+   *
+   * IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when
+   * homing and adds a guard period for endstop triggering.
    *
    * TMC2209 requires STEALTHCHOP enabled for SENSORLESS_HOMING
    */
diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h
index 78d4f7f143..cd63ed2fe2 100644
--- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h
+++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h
@@ -817,6 +817,11 @@
  */
 #define DEFAULT_MAX_FEEDRATE          { 100, 100, 100, 25 }
 
+//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#if ENABLED(LIMITED_MAX_FR_EDITING)
+  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Max Acceleration (change/s) change = mm/s
  * (Maximum start speed for accelerated moves)
@@ -825,6 +830,11 @@
  */
 #define DEFAULT_MAX_ACCELERATION      { 1000, 1000, 1000, 3000 }
 
+//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
+  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+#endif
+
 /**
  * Default Acceleration (change/s) change = mm/s
  * Override with M204
@@ -850,6 +860,11 @@
   #define DEFAULT_XJERK 10.0
   #define DEFAULT_YJERK DEFAULT_XJERK
   #define DEFAULT_ZJERK DEFAULT_XJERK // Must be same as XY for delta
+
+  //#define LIMITED_JERK_EDITING        // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
+  #if ENABLED(LIMITED_JERK_EDITING)
+    #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
+  #endif
 #endif
 
 #define DEFAULT_EJERK    5.0  // May be used by Linear Advance
diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
index 3a9b918669..dc03631c19 100644
--- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
+++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
@@ -2059,17 +2059,27 @@
   #define E5_HYBRID_THRESHOLD     30
 
   /**
+   * Use StallGuard2 to home / probe X, Y, Z.
+   *
    * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
-   * Use StallGuard2 to sense an obstacle and trigger an endstop.
    * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
    * X, Y, and Z homing will always be done in spreadCycle mode.
    *
-   * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
-   * Higher values make the system LESS sensitive.
-   * Lower value make the system MORE sensitive.
-   * Too low values can lead to false positives, while too high values will collide the axis without triggering.
-   * It is advised to set X/Y/Z_HOME_BUMP_MM to 0.
-   * M914 X/Y/Z to live tune the setting
+   * X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
+   * Use M914 X Y Z to set the stall threshold at runtime:
+   *
+   *  Sensitivity   TMC2209   Others
+   *    HIGHEST       255      -64    (Too sensitive => False positive)
+   *    LOWEST         0        63    (Too insensitive => No trigger)
+   *
+   * It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
+   *
+   * SPI_ENDSTOPS  *** Beta feature! *** TMC2130 Only ***
+   * Poll the driver through SPI to determine load when homing.
+   * Removes the need for a wire from DIAG1 to an endstop pin.
+   *
+   * IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when
+   * homing and adds a guard period for endstop triggering.
    *
    * TMC2209 requires STEALTHCHOP enabled for SENSORLESS_HOMING
    */
diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h
index efdb02d2c2..afef613082 100644
--- a/config/examples/makibox/Configuration_adv.h
+++ b/config/examples/makibox/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h
index d3b0595534..ef2a7f1ed5 100644
--- a/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *
diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h
index 35f18aa028..f795aabd0e 100644
--- a/config/examples/wt150/Configuration_adv.h
+++ b/config/examples/wt150/Configuration_adv.h
@@ -290,6 +290,9 @@
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
 //#define FAN_KICKSTART_TIME 100
 
+// Some coolers may require a non-zero "off" state.
+//#define FAN_OFF_PWM  1
+
 /**
  * PWM Fan Scaling
  *