diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index cdfaa49fb6..6d38e833cc 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -1806,18 +1806,18 @@
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+//#define LCD_BED_TRAMMING
 
-#if ENABLED(LEVEL_BED_CORNERS)
-  #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
-  #define LEVEL_CORNERS_HEIGHT      0.0   // (mm) Z height of nozzle at leveling points
-  #define LEVEL_CORNERS_Z_HOP       4.0   // (mm) Z height of nozzle between leveling points
-  //#define LEVEL_CENTER_TOO              // Move to the center after the last corner
-  //#define LEVEL_CORNERS_USE_PROBE
-  #if ENABLED(LEVEL_CORNERS_USE_PROBE)
-    #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
-    #define LEVEL_CORNERS_VERIFY_RAISED   // After adjustment triggers the probe, re-probe to verify
-    //#define LEVEL_CORNERS_AUDIO_FEEDBACK
+#if ENABLED(LCD_BED_TRAMMING)
+  #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 }  // (mm) Left, Front, Right, Back insets
+  #define BED_TRAMMING_HEIGHT      0.0        // (mm) Z height of nozzle at leveling points
+  #define BED_TRAMMING_Z_HOP       4.0        // (mm) Z height of nozzle between leveling points
+  //#define BED_TRAMMING_INCLUDE_CENTER       // Move to the center after the last corner
+  //#define BED_TRAMMING_USE_PROBE
+  #if ENABLED(BED_TRAMMING_USE_PROBE)
+    #define BED_TRAMMING_PROBE_TOLERANCE 0.1  // (mm)
+    #define BED_TRAMMING_VERIFY_RAISED        // After adjustment triggers the probe, re-probe to verify
+    //#define BED_TRAMMING_AUDIO_FEEDBACK
   #endif
 
   /**
@@ -1837,7 +1837,7 @@
    *  |  1       2  |   | 1         4 |    | 1         2 |   | 2           |
    *  LF --------- RF   LF --------- RF    LF --------- RF   LF --------- RF
    */
-  #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, RB, LB }
+  #define BED_TRAMMING_LEVELING_ORDER { LF, RF, RB, LB }
 #endif
 
 /**
diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h
index 6c025b1dbb..98f5ed3f48 100644
--- a/Marlin/src/inc/Conditionals_post.h
+++ b/Marlin/src/inc/Conditionals_post.h
@@ -266,7 +266,7 @@
  * No adjustable bed on non-cartesians
  */
 #if IS_KINEMATIC
-  #undef LEVEL_BED_CORNERS
+  #undef LCD_BED_TRAMMING
 #endif
 
 /**
diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h
index ebbd85ad1b..8cb87ca8bc 100644
--- a/Marlin/src/inc/SanityCheck.h
+++ b/Marlin/src/inc/SanityCheck.h
@@ -371,7 +371,7 @@
 #elif defined(FILAMENT_CHANGE_LOAD_LENGTH)
   #error "FILAMENT_CHANGE_LOAD_LENGTH is now FILAMENT_CHANGE_FAST_LOAD_LENGTH."
 #elif defined(LEVEL_CORNERS_INSET)
-  #error "LEVEL_CORNERS_INSET is now LEVEL_CORNERS_INSET_LFRB."
+  #error "LEVEL_CORNERS_INSET is now BED_TRAMMING_INSET_LFRB."
 #elif defined(BEZIER_JERK_CONTROL)
   #error "BEZIER_JERK_CONTROL is now S_CURVE_ACCELERATION."
 #elif HAS_JUNCTION_DEVIATION && defined(JUNCTION_DEVIATION_FACTOR)
@@ -627,6 +627,12 @@
   #error "Y_DUAL_STEPPER_DRIVERS is no longer needed and should be removed."
 #elif defined(NUM_Z_STEPPER_DRIVERS)
   #error "NUM_Z_STEPPER_DRIVERS is no longer needed and should be removed."
+#elif defined(LEVEL_BED_CORNERS)
+  #error "LEVEL_BED_CORNERS is now LCD_BED_TRAMMING."
+#elif defined(LEVEL_CORNERS_INSET_LFRB) || defined(LEVEL_CORNERS_HEIGHT) || defined(LEVEL_CORNERS_Z_HOP) || defined(LEVEL_CORNERS_USE_PROBE) || defined(LEVEL_CORNERS_PROBE_TOLERANCE) || defined(LEVEL_CORNERS_VERIFY_RAISED) || defined(LEVEL_CORNERS_AUDIO_FEEDBACK)
+  #error "LEVEL_CORNERS_* settings have been renamed BED_TRAMMING_*."
+#elif defined(LEVEL_CENTER_TOO)
+  #error "LEVEL_CENTER_TOO is now BED_TRAMMING_INCLUDE_CENTER."
 #endif
 
 constexpr float arm[] = AXIS_RELATIVE_MODES;
@@ -1824,14 +1830,14 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 
 #endif
 
-#if ENABLED(LEVEL_BED_CORNERS)
-  #ifndef LEVEL_CORNERS_INSET_LFRB
-    #error "LEVEL_BED_CORNERS requires LEVEL_CORNERS_INSET_LFRB values."
-  #elif ENABLED(LEVEL_CORNERS_USE_PROBE)
+#if ENABLED(LCD_BED_TRAMMING)
+  #ifndef BED_TRAMMING_INSET_LFRB
+    #error "LCD_BED_TRAMMING requires BED_TRAMMING_INSET_LFRB values."
+  #elif ENABLED(BED_TRAMMING_USE_PROBE)
     #if !HAS_BED_PROBE
-      #error "LEVEL_CORNERS_USE_PROBE requires a real probe."
+      #error "BED_TRAMMING_USE_PROBE requires a real probe."
     #elif ENABLED(SENSORLESS_PROBING)
-      #error "LEVEL_CORNERS_USE_PROBE is incompatible with SENSORLESS_PROBING."
+      #error "BED_TRAMMING_USE_PROBE is incompatible with SENSORLESS_PROBING."
     #endif
   #endif
 #endif
@@ -2952,8 +2958,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
     #error "DWIN_CREALITY_LCD does not support PID_EDIT_MENU or PID_AUTOTUNE_MENU."
   #elif EITHER(MPC_EDIT_MENU, MPC_AUTOTUNE_MENU)
     #error "DWIN_CREALITY_LCD does not support MPC_EDIT_MENU or MPC_AUTOTUNE_MENU."
-  #elif ENABLED(LEVEL_BED_CORNERS)
-    #error "DWIN_CREALITY_LCD does not support LEVEL_BED_CORNERS."
+  #elif ENABLED(LCD_BED_TRAMMING)
+    #error "DWIN_CREALITY_LCD does not support LCD_BED_TRAMMING."
   #elif BOTH(LCD_BED_LEVELING, PROBE_MANUALLY)
     #error "DWIN_CREALITY_LCD does not support LCD_BED_LEVELING with PROBE_MANUALLY."
   #endif
@@ -2964,8 +2970,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
     #error "DWIN_LCD_PROUI does not support PID_EDIT_MENU or PID_AUTOTUNE_MENU."
   #elif EITHER(MPC_EDIT_MENU, MPC_AUTOTUNE_MENU)
     #error "DWIN_LCD_PROUI does not support MPC_EDIT_MENU or MPC_AUTOTUNE_MENU."
-  #elif ENABLED(LEVEL_BED_CORNERS)
-    #error "DWIN_LCD_PROUI does not support LEVEL_BED_CORNERS."
+  #elif ENABLED(LCD_BED_TRAMMING)
+    #error "DWIN_LCD_PROUI does not support LCD_BED_TRAMMING."
   #elif BOTH(LCD_BED_LEVELING, PROBE_MANUALLY)
     #error "DWIN_LCD_PROUI does not support LCD_BED_LEVELING with PROBE_MANUALLY."
   #endif
@@ -4121,8 +4127,8 @@ static_assert(_PLUS_TEST(4), "HOMING_FEEDRATE_MM_M values must be positive.");
     #error "DGUS_LCD_UI_RELOADED requires a bed probe."
   #elif !HAS_MESH
     #error "DGUS_LCD_UI_RELOADED requires mesh leveling."
-  #elif DISABLED(LEVEL_BED_CORNERS)
-    #error "DGUS_LCD_UI_RELOADED requires LEVEL_BED_CORNERS."
+  #elif DISABLED(LCD_BED_TRAMMING)
+    #error "DGUS_LCD_UI_RELOADED requires LCD_BED_TRAMMING."
   #elif DISABLED(BABYSTEP_ALWAYS_AVAILABLE)
     #error "DGUS_LCD_UI_RELOADED requires BABYSTEP_ALWAYS_AVAILABLE."
   #elif DISABLED(BABYSTEP_ZPROBE_OFFSET)
diff --git a/Marlin/src/lcd/extui/dgus_reloaded/DGUSRxHandler.cpp b/Marlin/src/lcd/extui/dgus_reloaded/DGUSRxHandler.cpp
index cf95bb1d76..cef9c772e9 100644
--- a/Marlin/src/lcd/extui/dgus_reloaded/DGUSRxHandler.cpp
+++ b/Marlin/src/lcd/extui/dgus_reloaded/DGUSRxHandler.cpp
@@ -466,7 +466,7 @@ void DGUSRxHandler::MoveToPoint(DGUS_VP &vp, void *data_ptr) {
   }
 
   const uint8_t point = ((uint8_t*)data_ptr)[1];
-  constexpr float lfrb[4] = LEVEL_CORNERS_INSET_LFRB;
+  constexpr float lfrb[4] = BED_TRAMMING_INSET_LFRB;
   float x, y;
 
   switch (point) {
@@ -493,12 +493,12 @@ void DGUSRxHandler::MoveToPoint(DGUS_VP &vp, void *data_ptr) {
       break;
   }
 
-  if (ExtUI::getAxisPosition_mm(ExtUI::Z) < Z_MIN_POS + LEVEL_CORNERS_Z_HOP) {
-    ExtUI::setAxisPosition_mm(Z_MIN_POS + LEVEL_CORNERS_Z_HOP, ExtUI::Z);
+  if (ExtUI::getAxisPosition_mm(ExtUI::Z) < Z_MIN_POS + BED_TRAMMING_Z_HOP) {
+    ExtUI::setAxisPosition_mm(Z_MIN_POS + BED_TRAMMING_Z_HOP, ExtUI::Z);
   }
   ExtUI::setAxisPosition_mm(x, ExtUI::X);
   ExtUI::setAxisPosition_mm(y, ExtUI::Y);
-  ExtUI::setAxisPosition_mm(Z_MIN_POS + LEVEL_CORNERS_HEIGHT, ExtUI::Z);
+  ExtUI::setAxisPosition_mm(Z_MIN_POS + BED_TRAMMING_HEIGHT, ExtUI::Z);
 }
 
 void DGUSRxHandler::Probe(DGUS_VP &vp, void *data_ptr) {
diff --git a/Marlin/src/lcd/extui/dgus_reloaded/config/DGUS_Constants.h b/Marlin/src/lcd/extui/dgus_reloaded/config/DGUS_Constants.h
index 9b275fb2f5..846fd15942 100644
--- a/Marlin/src/lcd/extui/dgus_reloaded/config/DGUS_Constants.h
+++ b/Marlin/src/lcd/extui/dgus_reloaded/config/DGUS_Constants.h
@@ -71,15 +71,15 @@ static_assert((DGUS_LEVEL_GRID_SIZE == GRID_MAX_POINTS_X * GRID_MAX_POINTS_Y), "
   #define DGUS_DEFAULT_FILAMENT_LEN 10
 #endif
 
-#ifndef LEVEL_CORNERS_Z_HOP
-  #define LEVEL_CORNERS_Z_HOP 4.0
+#ifndef BED_TRAMMING_Z_HOP
+  #define BED_TRAMMING_Z_HOP 4.0
 #endif
 
-#ifndef LEVEL_CORNERS_HEIGHT
-  #define LEVEL_CORNERS_HEIGHT 0.0
+#ifndef BED_TRAMMING_HEIGHT
+  #define BED_TRAMMING_HEIGHT 0.0
 #endif
 
-static_assert(LEVEL_CORNERS_Z_HOP >= 0, "LEVEL_CORNERS_Z_HOP must be >= 0. Please update your configuration.");
+static_assert(BED_TRAMMING_Z_HOP >= 0, "BED_TRAMMING_Z_HOP must be >= 0. Please update your configuration.");
 
 #ifndef DGUS_LEVEL_CENTER_X
   #define DGUS_LEVEL_CENTER_X ((X_BED_SIZE) / 2)
diff --git a/Marlin/src/lcd/menu/menu.cpp b/Marlin/src/lcd/menu/menu.cpp
index 92be24aa06..13ef0d2bc1 100644
--- a/Marlin/src/lcd/menu/menu.cpp
+++ b/Marlin/src/lcd/menu/menu.cpp
@@ -47,7 +47,7 @@
 ///////////// Global Variables /////////////
 ////////////////////////////////////////////
 
-#if HAS_LEVELING && ANY(LEVEL_BED_CORNERS, PROBE_OFFSET_WIZARD, X_AXIS_TWIST_COMPENSATION)
+#if HAS_LEVELING && ANY(LCD_BED_TRAMMING, PROBE_OFFSET_WIZARD, X_AXIS_TWIST_COMPENSATION)
   bool leveling_was_active; // = false
 #endif
 #if ANY(PROBE_MANUALLY, MESH_BED_LEVELING, X_AXIS_TWIST_COMPENSATION)
diff --git a/Marlin/src/lcd/menu/menu.h b/Marlin/src/lcd/menu/menu.h
index fbee2c8501..67e337213a 100644
--- a/Marlin/src/lcd/menu/menu.h
+++ b/Marlin/src/lcd/menu/menu.h
@@ -211,7 +211,7 @@ void menu_move();
 void lcd_move_z();
 void _lcd_draw_homing();
 
-#define HAS_LINE_TO_Z ANY(DELTA, PROBE_MANUALLY, MESH_BED_LEVELING, LEVEL_BED_CORNERS)
+#define HAS_LINE_TO_Z ANY(DELTA, PROBE_MANUALLY, MESH_BED_LEVELING, LCD_BED_TRAMMING)
 
 #if HAS_LINE_TO_Z
   void line_to_z(const_float_t z);
@@ -258,7 +258,7 @@ inline void clear_menu_history() { screen_history_depth = 0; }
 
 #define STICKY_SCREEN(S) []{ ui.defer_status_screen(); ui.goto_screen(S); }
 
-#if HAS_LEVELING && ANY(LEVEL_BED_CORNERS, PROBE_OFFSET_WIZARD, X_AXIS_TWIST_COMPENSATION)
+#if HAS_LEVELING && ANY(LCD_BED_TRAMMING, PROBE_OFFSET_WIZARD, X_AXIS_TWIST_COMPENSATION)
   extern bool leveling_was_active;
 #endif
 
diff --git a/Marlin/src/lcd/menu/menu_bed_corners.cpp b/Marlin/src/lcd/menu/menu_bed_corners.cpp
index c820ff15e7..3fe0c582cb 100644
--- a/Marlin/src/lcd/menu/menu_bed_corners.cpp
+++ b/Marlin/src/lcd/menu/menu_bed_corners.cpp
@@ -26,7 +26,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if BOTH(HAS_MARLINUI_MENU, LEVEL_BED_CORNERS)
+#if BOTH(HAS_MARLINUI_MENU, LCD_BED_TRAMMING)
 
 #include "menu_item.h"
 #include "../../module/motion.h"
@@ -36,21 +36,21 @@
   #include "../../feature/bedlevel/bedlevel.h"
 #endif
 
-#ifndef LEVEL_CORNERS_Z_HOP
-  #define LEVEL_CORNERS_Z_HOP 4.0
+#ifndef BED_TRAMMING_Z_HOP
+  #define BED_TRAMMING_Z_HOP 4.0
 #endif
-#ifndef LEVEL_CORNERS_HEIGHT
-  #define LEVEL_CORNERS_HEIGHT 0.0
+#ifndef BED_TRAMMING_HEIGHT
+  #define BED_TRAMMING_HEIGHT 0.0
 #endif
 
-#if ENABLED(LEVEL_CORNERS_USE_PROBE)
+#if ENABLED(BED_TRAMMING_USE_PROBE)
   #include "../../module/probe.h"
   #include "../../module/endstops.h"
   #if ENABLED(BLTOUCH)
     #include "../../feature/bltouch.h"
   #endif
-  #ifndef LEVEL_CORNERS_PROBE_TOLERANCE
-    #define LEVEL_CORNERS_PROBE_TOLERANCE 0.2
+  #ifndef BED_TRAMMING_PROBE_TOLERANCE
+    #define BED_TRAMMING_PROBE_TOLERANCE 0.2
   #endif
   float last_z;
   int good_points;
@@ -64,32 +64,32 @@
 
 #endif
 
-static_assert(LEVEL_CORNERS_Z_HOP >= 0, "LEVEL_CORNERS_Z_HOP must be >= 0. Please update your configuration.");
+static_assert(BED_TRAMMING_Z_HOP >= 0, "BED_TRAMMING_Z_HOP must be >= 0. Please update your configuration.");
 
-#ifndef LEVEL_CORNERS_LEVELING_ORDER
-  #define LEVEL_CORNERS_LEVELING_ORDER { LF, RF, LB, RB } // Default
-  //#define LEVEL_CORNERS_LEVELING_ORDER { LF, LB, RF  }  // 3 hard-coded points
-  //#define LEVEL_CORNERS_LEVELING_ORDER { LF, RF }       // 3-Point tramming - Rear
-  //#define LEVEL_CORNERS_LEVELING_ORDER { LF, LB }       // 3-Point tramming - Right
-  //#define LEVEL_CORNERS_LEVELING_ORDER { RF, RB }       // 3-Point tramming - Left
-  //#define LEVEL_CORNERS_LEVELING_ORDER { LB, RB }       // 3-Point tramming - Front
+#ifndef BED_TRAMMING_LEVELING_ORDER
+  #define BED_TRAMMING_LEVELING_ORDER { LF, RF, LB, RB } // Default
+  //#define BED_TRAMMING_LEVELING_ORDER { LF, LB, RF  }  // 3 hard-coded points
+  //#define BED_TRAMMING_LEVELING_ORDER { LF, RF }       // 3-Point tramming - Rear
+  //#define BED_TRAMMING_LEVELING_ORDER { LF, LB }       // 3-Point tramming - Right
+  //#define BED_TRAMMING_LEVELING_ORDER { RF, RB }       // 3-Point tramming - Left
+  //#define BED_TRAMMING_LEVELING_ORDER { LB, RB }       // 3-Point tramming - Front
 #endif
 
 #define LF 1
 #define RF 2
 #define RB 3
 #define LB 4
-constexpr int lco[] = LEVEL_CORNERS_LEVELING_ORDER;
+constexpr int lco[] = BED_TRAMMING_LEVELING_ORDER;
 constexpr bool level_corners_3_points = COUNT(lco) == 2;
-static_assert(level_corners_3_points || COUNT(lco) == 4, "LEVEL_CORNERS_LEVELING_ORDER must have exactly 2 or 4 corners.");
+static_assert(level_corners_3_points || COUNT(lco) == 4, "BED_TRAMMING_LEVELING_ORDER must have exactly 2 or 4 corners.");
 
 constexpr int lcodiff = ABS(lco[0] - lco[1]);
-static_assert(COUNT(lco) == 4 || lcodiff == 1 || lcodiff == 3, "The first two LEVEL_CORNERS_LEVELING_ORDER corners must be on the same edge.");
+static_assert(COUNT(lco) == 4 || lcodiff == 1 || lcodiff == 3, "The first two BED_TRAMMING_LEVELING_ORDER corners must be on the same edge.");
 
 constexpr int nr_edge_points = level_corners_3_points ? 3 : 4;
-constexpr int available_points = nr_edge_points + ENABLED(LEVEL_CENTER_TOO);
-constexpr int center_index = TERN(LEVEL_CENTER_TOO, available_points - 1, -1);
-constexpr float inset_lfrb[4] = LEVEL_CORNERS_INSET_LFRB;
+constexpr int available_points = nr_edge_points + ENABLED(BED_TRAMMING_INCLUDE_CENTER);
+constexpr int center_index = TERN(BED_TRAMMING_INCLUDE_CENTER, available_points - 1, -1);
+constexpr float inset_lfrb[4] = BED_TRAMMING_INSET_LFRB;
 constexpr xy_pos_t lf { (X_MIN_BED) + inset_lfrb[0], (Y_MIN_BED) + inset_lfrb[1] },
                    rb { (X_MAX_BED) - inset_lfrb[2], (Y_MAX_BED) - inset_lfrb[3] };
 
@@ -120,12 +120,12 @@ static void _lcd_level_bed_corners_get_next_position() {
         if ((lco[0] == LF && lco[1] == LB) || (lco[0] == LB && lco[1] == LF)) current_position.x = rb.x; // Center Right
         if ((lco[0] == RF && lco[1] == RB) || (lco[0] == RB && lco[1] == RF)) current_position.x = lf.x; // Left Center
         if ((lco[0] == LF && lco[1] == RF) || (lco[0] == RF && lco[1] == LF)) current_position.y = rb.y; // Center Back
-        #if DISABLED(LEVEL_CENTER_TOO) && ENABLED(LEVEL_CORNERS_USE_PROBE)
+        #if DISABLED(BED_TRAMMING_INCLUDE_CENTER) && ENABLED(BED_TRAMMING_USE_PROBE)
           bed_corner++;  // Must increment the count to ensure it resets the loop if the 3rd point is out of tolerance
         #endif
         break;
 
-      #if ENABLED(LEVEL_CENTER_TOO)
+      #if ENABLED(BED_TRAMMING_INCLUDE_CENTER)
         case 3:
           current_position.set(X_CENTER, Y_CENTER);
           break;
@@ -134,9 +134,9 @@ static void _lcd_level_bed_corners_get_next_position() {
   }
   else {
     // Four-Corner Bed Tramming with optional center
-    if (TERN0(LEVEL_CENTER_TOO, bed_corner == center_index)) {
+    if (TERN0(BED_TRAMMING_INCLUDE_CENTER, bed_corner == center_index)) {
       current_position.set(X_CENTER, Y_CENTER);
-      TERN_(LEVEL_CORNERS_USE_PROBE, good_points--); // Decrement to allow one additional probe point
+      TERN_(BED_TRAMMING_USE_PROBE, good_points--); // Decrement to allow one additional probe point
     }
     else {
       current_position = lf;                       // Left front
@@ -152,10 +152,10 @@ static void _lcd_level_bed_corners_get_next_position() {
 /**
  * Level corners, starting in the front-left corner.
  */
-#if ENABLED(LEVEL_CORNERS_USE_PROBE)
+#if ENABLED(BED_TRAMMING_USE_PROBE)
 
   #define VALIDATE_POINT(X, Y, STR) static_assert(Probe::build_time::can_reach((X), (Y)), \
-    "LEVEL_CORNERS_INSET_LFRB " STR " inset is not reachable with the default NOZZLE_TO_PROBE offset and PROBING_MARGIN.")
+    "BED_TRAMMING_INSET_LFRB " STR " inset is not reachable with the default NOZZLE_TO_PROBE offset and PROBING_MARGIN.")
   VALIDATE_POINT(lf.x, Y_CENTER, "left"); VALIDATE_POINT(X_CENTER, lf.y, "front");
   VALIDATE_POINT(rb.x, Y_CENTER, "right"); VALIDATE_POINT(X_CENTER, rb.y, "back");
 
@@ -216,16 +216,16 @@ static void _lcd_level_bed_corners_get_next_position() {
   }
 
   bool _lcd_level_bed_corners_probe(bool verify=false) {
-    if (verify) do_blocking_move_to_z(current_position.z + LEVEL_CORNERS_Z_HOP); // do clearance if needed
+    if (verify) do_blocking_move_to_z(current_position.z + BED_TRAMMING_Z_HOP); // do clearance if needed
     TERN_(BLTOUCH, if (!bltouch.high_speed_mode) bltouch.deploy()); // Deploy in LOW SPEED MODE on every probe action
-    do_blocking_move_to_z(last_z - LEVEL_CORNERS_PROBE_TOLERANCE, MMM_TO_MMS(Z_PROBE_FEEDRATE_SLOW)); // Move down to lower tolerance
+    do_blocking_move_to_z(last_z - BED_TRAMMING_PROBE_TOLERANCE, MMM_TO_MMS(Z_PROBE_FEEDRATE_SLOW)); // Move down to lower tolerance
     if (TEST(endstops.trigger_state(), Z_MIN_PROBE)) { // check if probe triggered
       endstops.hit_on_purpose();
       set_current_from_steppers_for_axis(Z_AXIS);
       sync_plan_position();
       TERN_(BLTOUCH, if (!bltouch.high_speed_mode) bltouch.stow()); // Stow in LOW SPEED MODE on every trigger
       // Triggered outside tolerance range?
-      if (ABS(current_position.z - last_z) > LEVEL_CORNERS_PROBE_TOLERANCE) {
+      if (ABS(current_position.z - last_z) > BED_TRAMMING_PROBE_TOLERANCE) {
         last_z = current_position.z; // Above tolerance. Set a new Z for subsequent corners.
         good_points = 0;             // ...and start over
       }
@@ -245,7 +245,7 @@ static void _lcd_level_bed_corners_get_next_position() {
       probe_triggered = PROBE_TRIGGERED();
       if (probe_triggered) {
         endstops.hit_on_purpose();
-        TERN_(LEVEL_CORNERS_AUDIO_FEEDBACK, BUZZ(200, 600));
+        TERN_(BED_TRAMMING_AUDIO_FEEDBACK, BUZZ(200, 600));
       }
       idle();
     }
@@ -255,8 +255,8 @@ static void _lcd_level_bed_corners_get_next_position() {
   }
 
   void _lcd_test_corners() {
-    bed_corner = TERN(LEVEL_CENTER_TOO, center_index, 0);
-    last_z = LEVEL_CORNERS_HEIGHT;
+    bed_corner = TERN(BED_TRAMMING_INCLUDE_CENTER, center_index, 0);
+    last_z = BED_TRAMMING_HEIGHT;
     endstops.enable_z_probe(true);
     good_points = 0;
     ui.goto_screen(_lcd_draw_probing);
@@ -264,7 +264,7 @@ static void _lcd_level_bed_corners_get_next_position() {
       ui.refresh(LCDVIEW_REDRAW_NOW);
       _lcd_draw_probing();                                // update screen with # of good points
 
-      do_blocking_move_to_z(current_position.z + LEVEL_CORNERS_Z_HOP + TERN0(BLTOUCH, bltouch.z_extra_clearance())); // clearance
+      do_blocking_move_to_z(current_position.z + BED_TRAMMING_Z_HOP + TERN0(BLTOUCH, bltouch.z_extra_clearance())); // clearance
 
       _lcd_level_bed_corners_get_next_position();         // Select next corner coordinates
       current_position -= probe.offset_xy;                // Account for probe offsets
@@ -273,7 +273,7 @@ static void _lcd_level_bed_corners_get_next_position() {
       TERN_(BLTOUCH, if (bltouch.high_speed_mode) bltouch.deploy()); // Deploy in HIGH SPEED MODE
       if (!_lcd_level_bed_corners_probe()) {              // Probe down to tolerance
         if (_lcd_level_bed_corners_raise()) {             // Prompt user to raise bed if needed
-          #if ENABLED(LEVEL_CORNERS_VERIFY_RAISED)        // Verify
+          #if ENABLED(BED_TRAMMING_VERIFY_RAISED)        // Verify
             while (!_lcd_level_bed_corners_probe(true)) { // Loop while corner verified
               if (!_lcd_level_bed_corners_raise()) {      // Prompt user to raise bed if needed
                 if (corner_probing_done) return;          // Done was selected
@@ -294,7 +294,7 @@ static void _lcd_level_bed_corners_get_next_position() {
     #if ENABLED(BLTOUCH)
       if (bltouch.high_speed_mode) {
         // In HIGH SPEED MODE do clearance and stow at the very end
-        do_blocking_move_to_z(current_position.z + LEVEL_CORNERS_Z_HOP);
+        do_blocking_move_to_z(current_position.z + BED_TRAMMING_Z_HOP);
         bltouch.stow();
       }
     #endif
@@ -303,25 +303,25 @@ static void _lcd_level_bed_corners_get_next_position() {
     ui.set_selection(true);
   }
 
-#else // !LEVEL_CORNERS_USE_PROBE
+#else // !BED_TRAMMING_USE_PROBE
 
   static void _lcd_goto_next_corner() {
-    line_to_z(LEVEL_CORNERS_Z_HOP);
+    line_to_z(BED_TRAMMING_Z_HOP);
 
     // Select next corner coordinates
     _lcd_level_bed_corners_get_next_position();
 
     line_to_current_position(manual_feedrate_mm_s.x);
-    line_to_z(LEVEL_CORNERS_HEIGHT);
+    line_to_z(BED_TRAMMING_HEIGHT);
     if (++bed_corner >= available_points) bed_corner = 0;
   }
 
-#endif // !LEVEL_CORNERS_USE_PROBE
+#endif // !BED_TRAMMING_USE_PROBE
 
 static void _lcd_level_bed_corners_homing() {
   _lcd_draw_homing();
   if (!all_axes_homed()) return;
-  #if ENABLED(LEVEL_CORNERS_USE_PROBE)
+  #if ENABLED(BED_TRAMMING_USE_PROBE)
     _lcd_test_corners();
     if (corner_probing_done) ui.goto_previous_screen_no_defer();
     TERN_(HAS_LEVELING, set_bed_leveling_enabled(leveling_was_active));
@@ -333,11 +333,11 @@ static void _lcd_level_bed_corners_homing() {
           GET_TEXT_F(MSG_BUTTON_NEXT), GET_TEXT_F(MSG_BUTTON_DONE)
         , _lcd_goto_next_corner
         , []{
-            line_to_z(LEVEL_CORNERS_Z_HOP); // Raise Z off the bed when done
+            line_to_z(BED_TRAMMING_Z_HOP); // Raise Z off the bed when done
             TERN_(HAS_LEVELING, set_bed_leveling_enabled(leveling_was_active));
             ui.goto_previous_screen_no_defer();
           }
-        , GET_TEXT_F(TERN(LEVEL_CENTER_TOO, MSG_LEVEL_BED_NEXT_POINT, MSG_NEXT_CORNER))
+        , GET_TEXT_F(TERN(BED_TRAMMING_INCLUDE_CENTER, MSG_LEVEL_BED_NEXT_POINT, MSG_NEXT_CORNER))
         , (const char*)nullptr, F("?")
       );
     });
@@ -362,4 +362,4 @@ void _lcd_level_bed_corners() {
   ui.goto_screen(_lcd_level_bed_corners_homing);
 }
 
-#endif // HAS_MARLINUI_MENU && LEVEL_BED_CORNERS
+#endif // HAS_MARLINUI_MENU && LCD_BED_TRAMMING
diff --git a/Marlin/src/lcd/menu/menu_bed_leveling.cpp b/Marlin/src/lcd/menu/menu_bed_leveling.cpp
index 142da1696a..294666e356 100644
--- a/Marlin/src/lcd/menu/menu_bed_leveling.cpp
+++ b/Marlin/src/lcd/menu/menu_bed_leveling.cpp
@@ -290,7 +290,7 @@ void menu_bed_leveling() {
     EDIT_ITEM(LCD_Z_OFFSET_TYPE, MSG_ZPROBE_ZOFFSET, &probe.offset.z, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
   #endif
 
-  #if ENABLED(LEVEL_BED_CORNERS)
+  #if ENABLED(LCD_BED_TRAMMING)
     SUBMENU(MSG_BED_TRAMMING, _lcd_level_bed_corners);
   #endif
 
diff --git a/Marlin/src/lcd/menu/menu_item.h b/Marlin/src/lcd/menu/menu_item.h
index 80a0872da6..85ae1c4b41 100644
--- a/Marlin/src/lcd/menu/menu_item.h
+++ b/Marlin/src/lcd/menu/menu_item.h
@@ -466,7 +466,7 @@ class MenuItem_bool : public MenuEditItemBase {
 #define YESNO_ITEM_N_F(N,FLABEL, V...)             CONFIRM_ITEM_N_F(N, FLABEL, MSG_YES, MSG_NO, ##V)
 #define YESNO_ITEM_N(N,LABEL, V...)                  YESNO_ITEM_N_F(N, GET_TEXT_F(LABEL), ##V)
 
-#if ENABLED(LEVEL_BED_CORNERS)
+#if ENABLED(LCD_BED_TRAMMING)
   void _lcd_level_bed_corners();
 #endif
 
diff --git a/Marlin/src/lcd/menu/menu_motion.cpp b/Marlin/src/lcd/menu/menu_motion.cpp
index 5704ebedb4..25f2018377 100644
--- a/Marlin/src/lcd/menu/menu_motion.cpp
+++ b/Marlin/src/lcd/menu/menu_motion.cpp
@@ -491,7 +491,7 @@ void menu_motion() {
 
   #endif
 
-  #if ENABLED(LEVEL_BED_CORNERS) && DISABLED(LCD_BED_LEVELING)
+  #if ENABLED(LCD_BED_TRAMMING) && DISABLED(LCD_BED_LEVELING)
     SUBMENU(MSG_BED_TRAMMING, _lcd_level_bed_corners);
   #endif
 
diff --git a/buildroot/share/PlatformIO/scripts/common-dependencies.h b/buildroot/share/PlatformIO/scripts/common-dependencies.h
index 4aa97c41ad..da2d380a82 100644
--- a/buildroot/share/PlatformIO/scripts/common-dependencies.h
+++ b/buildroot/share/PlatformIO/scripts/common-dependencies.h
@@ -53,7 +53,7 @@
   #if ENABLED(BACKLASH_GCODE)
     #define HAS_MENU_BACKLASH
   #endif
-  #if ENABLED(LEVEL_BED_CORNERS)
+  #if ENABLED(LCD_BED_TRAMMING)
     #define HAS_MENU_BED_CORNERS
   #endif
   #if ENABLED(CANCEL_OBJECTS)
diff --git a/buildroot/tests/BIGTREE_GTR_V1_0_usb_flash_drive b/buildroot/tests/BIGTREE_GTR_V1_0_usb_flash_drive
index 34bf77be27..78aec13295 100755
--- a/buildroot/tests/BIGTREE_GTR_V1_0_usb_flash_drive
+++ b/buildroot/tests/BIGTREE_GTR_V1_0_usb_flash_drive
@@ -10,7 +10,7 @@ restore_configs
 opt_set MOTHERBOARD BOARD_BTT_GTR_V1_0 SERIAL_PORT 3 \
         EXTRUDERS 8 TEMP_SENSOR_1 1 TEMP_SENSOR_2 1 TEMP_SENSOR_3 1 TEMP_SENSOR_4 1 TEMP_SENSOR_5 1 TEMP_SENSOR_6 1 TEMP_SENSOR_7 1
 opt_enable SDSUPPORT USB_FLASH_DRIVE_SUPPORT USE_OTG_USB_HOST \
-           REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER BLTOUCH LEVEL_BED_CORNERS LEVEL_CORNERS_USE_PROBE \
+           REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER BLTOUCH LCD_BED_TRAMMING BED_TRAMMING_USE_PROBE \
            NEOPIXEL_LED Z_SAFE_HOMING FILAMENT_RUNOUT_SENSOR NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE
 # Not necessary to enable auto-fan for all extruders to hit problematic code paths
 opt_set E0_AUTO_FAN_PIN PC10 E1_AUTO_FAN_PIN PC11 E2_AUTO_FAN_PIN PC12 NEOPIXEL_PIN PF13 \
diff --git a/buildroot/tests/LPC1769 b/buildroot/tests/LPC1769
index 3fe99734ca..086dffffc9 100755
--- a/buildroot/tests/LPC1769
+++ b/buildroot/tests/LPC1769
@@ -21,7 +21,7 @@ opt_set MOTHERBOARD BOARD_SMOOTHIEBOARD \
 opt_enable TFTGLCD_PANEL_SPI SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
            MAX31865_SENSOR_OHMS_0 MAX31865_CALIBRATION_OHMS_0 \
            FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
-           BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET LEVEL_CORNERS_USE_PROBE LEVEL_CORNERS_VERIFY_RAISED \
+           BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BED_TRAMMING_USE_PROBE BED_TRAMMING_VERIFY_RAISED \
            PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
            Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \
            LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES SDCARD_SORT_ALPHA EMERGENCY_PARSER
diff --git a/buildroot/tests/rambo b/buildroot/tests/rambo
index f8fef704f1..167f6d89aa 100755
--- a/buildroot/tests/rambo
+++ b/buildroot/tests/rambo
@@ -24,7 +24,7 @@ opt_enable USE_ZMAX_PLUG REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_P
            BLINKM PCA9533 PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \
            NEOPIXEL_LED NEOPIXEL_PIN CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CASE_LIGHT_MENU \
            PID_PARAMS_PER_HOTEND PID_AUTOTUNE_MENU PID_EDIT_MENU LCD_SHOW_E_TOTAL \
-           PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 LEVEL_BED_CORNERS LEVEL_CENTER_TOO \
+           PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 LCD_BED_TRAMMING BED_TRAMMING_INCLUDE_CENTER \
            NOZZLE_PARK_FEATURE FILAMENT_RUNOUT_SENSOR FILAMENT_RUNOUT_DISTANCE_MM \
            ADVANCED_PAUSE_FEATURE FILAMENT_LOAD_UNLOAD_GCODES FILAMENT_UNLOAD_ALL_EXTRUDERS \
            PASSWORD_FEATURE PASSWORD_ON_STARTUP PASSWORD_ON_SD_PRINT_MENU PASSWORD_AFTER_SD_PRINT_END PASSWORD_AFTER_SD_PRINT_ABORT \
@@ -51,13 +51,13 @@ opt_set MOTHERBOARD BOARD_RAMBO \
         DEFAULT_MAX_ACCELERATION '{ 3000, 3000, 100 }' \
         MANUAL_FEEDRATE '{ 50*60, 50*60, 4*60 }' \
         AXIS_RELATIVE_MODES '{ false, false, false }' \
-        LEVEL_CORNERS_LEVELING_ORDER '{ LF, RF }' \
+        BED_TRAMMING_LEVELING_ORDER '{ LF, RF }' \
         X2_DRIVER_TYPE A4988 Y2_DRIVER_TYPE A4988
 opt_enable USE_XMAX_PLUG USE_YMAX_PLUG USE_ZMAX_PLUG \
            REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER REVERSE_ENCODER_DIRECTION SDSUPPORT EEPROM_SETTINGS \
            S_CURVE_ACCELERATION X_DUAL_ENDSTOPS Y_DUAL_ENDSTOPS \
            ADAPTIVE_STEP_SMOOTHING CNC_COORDINATE_SYSTEMS GCODE_MOTION_MODES \
-           LEVEL_BED_CORNERS LEVEL_CENTER_TOO
+           LCD_BED_TRAMMING BED_TRAMMING_INCLUDE_CENTER
 opt_disable MIN_SOFTWARE_ENDSTOP_Z MAX_SOFTWARE_ENDSTOPS
 exec_test $1 $2 "Rambo CNC Configuration" "$3"