Merge remote-tracking branch 'MarlinFirmware/Development' into Development
Conflicts: Marlin/Configuration.h
This commit is contained in:
Chris Roadfeldt
commit
3be00cce6f
|
|
@ -265,16 +265,14 @@
|
|||
#ifndef POWER_SUPPLY
|
||||
#define POWER_SUPPLY 1
|
||||
#endif
|
||||
// 1 = ATX
|
||||
#if (POWER_SUPPLY == 1)
|
||||
#if (POWER_SUPPLY == 1) // 1 = ATX
|
||||
#define PS_ON_AWAKE LOW
|
||||
#define PS_ON_ASLEEP HIGH
|
||||
#endif
|
||||
// 2 = X-Box 360 203W
|
||||
#if (POWER_SUPPLY == 2)
|
||||
#elif (POWER_SUPPLY == 2) // 2 = X-Box 360 203W
|
||||
#define PS_ON_AWAKE HIGH
|
||||
#define PS_ON_ASLEEP LOW
|
||||
#endif
|
||||
#define HAS_POWER_SWITCH (POWER_SUPPLY > 0 && defined(PS_ON_PIN) && PS_ON_PIN >= 0)
|
||||
|
||||
/**
|
||||
* Temp Sensor defines
|
||||
|
|
|
|||
|
|
@ -302,14 +302,19 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
|||
// Enable this option for Toshiba steppers
|
||||
// #define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// The pullups are needed if you directly connect a mechanical endstop between the signal and ground pins.
|
||||
#define ENDSTOPPULLUP_XMAX
|
||||
#define ENDSTOPPULLUP_YMAX
|
||||
#define ENDSTOPPULLUP_ZMAX
|
||||
#define ENDSTOPPULLUP_XMIN
|
||||
#define ENDSTOPPULLUP_YMIN
|
||||
#define ENDSTOPPULLUP_ZMIN
|
||||
#define ENDSTOPPULLUP_ZPROBE
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
#ifndef ENDSTOPPULLUPS
|
||||
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
||||
// #define ENDSTOPPULLUP_XMAX
|
||||
// #define ENDSTOPPULLUP_YMAX
|
||||
// #define ENDSTOPPULLUP_ZMAX
|
||||
// #define ENDSTOPPULLUP_XMIN
|
||||
// #define ENDSTOPPULLUP_YMIN
|
||||
// #define ENDSTOPPULLUP_ZMIN
|
||||
#endif
|
||||
>>>>>>> MarlinFirmware/Development
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
|
|
|
|||
|
|
@ -168,12 +168,12 @@
|
|||
// M401 - Lower z-probe if present
|
||||
// M402 - Raise z-probe if present
|
||||
// M404 - N<dia in mm> Enter the nominal filament width (3mm, 1.75mm ) or will display nominal filament width without parameters
|
||||
// M405 - Turn on Filament Sensor extrusion control. Optional D<delay in cm> to set delay in centimeters between sensor and extruder
|
||||
// M406 - Turn off Filament Sensor extrusion control
|
||||
// M407 - Displays measured filament diameter
|
||||
// M405 - Turn on Filament Sensor extrusion control. Optional D<delay in cm> to set delay in centimeters between sensor and extruder
|
||||
// M406 - Turn off Filament Sensor extrusion control
|
||||
// M407 - Display measured filament diameter
|
||||
// M500 - Store parameters in EEPROM
|
||||
// M501 - Read parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
// M502 - Revert to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
// M502 - Revert to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
// M503 - Print the current settings (from memory not from EEPROM). Use S0 to leave off headings.
|
||||
// M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
|
||||
// M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
|
||||
|
|
@ -273,7 +273,7 @@ int fanSpeed = 0;
|
|||
|
||||
#endif // FWRETRACT
|
||||
|
||||
#ifdef ULTIPANEL
|
||||
#if defined(ULTIPANEL) && HAS_POWER_SWITCH
|
||||
bool powersupply =
|
||||
#ifdef PS_DEFAULT_OFF
|
||||
false
|
||||
|
|
@ -311,14 +311,14 @@ int fanSpeed = 0;
|
|||
bool cancel_heatup = false;
|
||||
|
||||
#ifdef FILAMENT_SENSOR
|
||||
//Variables for Filament Sensor input
|
||||
float filament_width_nominal=DEFAULT_NOMINAL_FILAMENT_DIA; //Set nominal filament width, can be changed with M404
|
||||
bool filament_sensor=false; //M405 turns on filament_sensor control, M406 turns it off
|
||||
float filament_width_meas=DEFAULT_MEASURED_FILAMENT_DIA; //Stores the measured filament diameter
|
||||
signed char measurement_delay[MAX_MEASUREMENT_DELAY+1]; //ring buffer to delay measurement store extruder factor after subtracting 100
|
||||
int delay_index1=0; //index into ring buffer
|
||||
int delay_index2=-1; //index into ring buffer - set to -1 on startup to indicate ring buffer needs to be initialized
|
||||
float delay_dist=0; //delay distance counter
|
||||
//Variables for Filament Sensor input
|
||||
float filament_width_nominal = DEFAULT_NOMINAL_FILAMENT_DIA; //Set nominal filament width, can be changed with M404
|
||||
bool filament_sensor = false; //M405 turns on filament_sensor control, M406 turns it off
|
||||
float filament_width_meas = DEFAULT_MEASURED_FILAMENT_DIA; //Stores the measured filament diameter
|
||||
signed char measurement_delay[MAX_MEASUREMENT_DELAY+1]; //ring buffer to delay measurement store extruder factor after subtracting 100
|
||||
int delay_index1 = 0; //index into ring buffer
|
||||
int delay_index2 = -1; //index into ring buffer - set to -1 on startup to indicate ring buffer needs to be initialized
|
||||
float delay_dist = 0; //delay distance counter
|
||||
int meas_delay_cm = MEASUREMENT_DELAY_CM; //distance delay setting
|
||||
#endif
|
||||
|
||||
|
|
@ -519,8 +519,8 @@ void setup_powerhold()
|
|||
#if defined(SUICIDE_PIN) && SUICIDE_PIN > -1
|
||||
OUT_WRITE(SUICIDE_PIN, HIGH);
|
||||
#endif
|
||||
#if defined(PS_ON_PIN) && PS_ON_PIN > -1
|
||||
#if defined(PS_DEFAULT_OFF)
|
||||
#if HAS_POWER_SWITCH
|
||||
#ifdef PS_DEFAULT_OFF
|
||||
OUT_WRITE(PS_ON_PIN, PS_ON_ASLEEP);
|
||||
#else
|
||||
OUT_WRITE(PS_ON_PIN, PS_ON_AWAKE);
|
||||
|
|
@ -3269,7 +3269,7 @@ inline void gcode_M140() {
|
|||
if (code_seen('S')) setTargetBed(code_value());
|
||||
}
|
||||
|
||||
#if defined(PS_ON_PIN) && PS_ON_PIN > -1
|
||||
#if HAS_POWER_SWITCH
|
||||
|
||||
/**
|
||||
* M80: Turn on Power Supply
|
||||
|
|
@ -3291,10 +3291,12 @@ inline void gcode_M140() {
|
|||
#endif
|
||||
}
|
||||
|
||||
#endif // PS_ON_PIN
|
||||
#endif // HAS_POWER_SWITCH
|
||||
|
||||
/**
|
||||
* M81: Turn off Power Supply
|
||||
* M81: Turn off Power, including Power Supply, if there is one.
|
||||
*
|
||||
* This code should ALWAYS be available for EMERGENCY SHUTDOWN!
|
||||
*/
|
||||
inline void gcode_M81() {
|
||||
disable_heater();
|
||||
|
|
@ -3309,16 +3311,19 @@ inline void gcode_M81() {
|
|||
#if defined(SUICIDE_PIN) && SUICIDE_PIN > -1
|
||||
st_synchronize();
|
||||
suicide();
|
||||
#elif defined(PS_ON_PIN) && PS_ON_PIN > -1
|
||||
#elif HAS_POWER_SWITCH
|
||||
OUT_WRITE(PS_ON_PIN, PS_ON_ASLEEP);
|
||||
#endif
|
||||
#ifdef ULTIPANEL
|
||||
powersupply = false;
|
||||
#if HAS_POWER_SWITCH
|
||||
powersupply = false;
|
||||
#endif
|
||||
LCD_MESSAGEPGM(MACHINE_NAME " " MSG_OFF ".");
|
||||
lcd_update();
|
||||
#endif
|
||||
}
|
||||
|
||||
|
||||
/**
|
||||
* M82: Set E codes absolute (default)
|
||||
*/
|
||||
|
|
@ -4859,15 +4864,15 @@ void process_commands() {
|
|||
#endif //HEATER_2_PIN
|
||||
#endif //BARICUDA
|
||||
|
||||
#if defined(PS_ON_PIN) && PS_ON_PIN > -1
|
||||
#if HAS_POWER_SWITCH
|
||||
|
||||
case 80: // M80 - Turn on Power Supply
|
||||
gcode_M80();
|
||||
break;
|
||||
|
||||
#endif // PS_ON_PIN
|
||||
#endif // HAS_POWER_SWITCH
|
||||
|
||||
case 81: // M81 - Turn off Power Supply
|
||||
case 81: // M81 - Turn off Power, including Power Supply, if possible
|
||||
gcode_M81();
|
||||
break;
|
||||
|
||||
|
|
@ -5841,19 +5846,17 @@ void kill()
|
|||
disable_e2();
|
||||
disable_e3();
|
||||
|
||||
#if defined(PS_ON_PIN) && PS_ON_PIN > -1
|
||||
pinMode(PS_ON_PIN,INPUT);
|
||||
#endif
|
||||
#if HAS_POWER_SWITCH
|
||||
pinMode(PS_ON_PIN, INPUT);
|
||||
#endif
|
||||
|
||||
SERIAL_ERROR_START;
|
||||
SERIAL_ERRORLNPGM(MSG_ERR_KILLED);
|
||||
LCD_ALERTMESSAGEPGM(MSG_KILLED);
|
||||
|
||||
// FMC small patch to update the LCD before ending
|
||||
sei(); // enable interrupts
|
||||
for ( int i=5; i--; lcd_update())
|
||||
{
|
||||
delay(200);
|
||||
}
|
||||
for (int i = 5; i--; lcd_update()) delay(200); // Wait a short time
|
||||
cli(); // disable interrupts
|
||||
suicide();
|
||||
while(1) { /* Intentionally left empty */ } // Wait for reset
|
||||
|
|
|
|||
|
|
@ -44,7 +44,9 @@ static void lcd_status_screen();
|
|||
|
||||
#ifdef ULTIPANEL
|
||||
|
||||
extern bool powersupply;
|
||||
#if HAS_POWER_SWITCH
|
||||
extern bool powersupply;
|
||||
#endif
|
||||
static float manual_feedrate[] = MANUAL_FEEDRATE;
|
||||
static void lcd_main_menu();
|
||||
static void lcd_tune_menu();
|
||||
|
|
@ -616,6 +618,7 @@ static void lcd_prepare_menu() {
|
|||
MENU_ITEM(gcode, MSG_AUTO_HOME, PSTR("G28"));
|
||||
MENU_ITEM(function, MSG_SET_HOME_OFFSETS, lcd_set_home_offsets);
|
||||
//MENU_ITEM(gcode, MSG_SET_ORIGIN, PSTR("G92 X0 Y0 Z0"));
|
||||
|
||||
#if TEMP_SENSOR_0 != 0
|
||||
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 || TEMP_SENSOR_BED != 0
|
||||
MENU_ITEM(submenu, MSG_PREHEAT_PLA, lcd_preheat_pla_menu);
|
||||
|
|
@ -625,15 +628,16 @@ static void lcd_prepare_menu() {
|
|||
MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs0);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown);
|
||||
#if defined(POWER_SUPPLY) && POWER_SUPPLY > 0 && defined(PS_ON_PIN) && PS_ON_PIN > -1
|
||||
if (powersupply) {
|
||||
|
||||
#if HAS_POWER_SWITCH
|
||||
if (powersupply)
|
||||
MENU_ITEM(gcode, MSG_SWITCH_PS_OFF, PSTR("M81"));
|
||||
}
|
||||
else {
|
||||
else
|
||||
MENU_ITEM(gcode, MSG_SWITCH_PS_ON, PSTR("M80"));
|
||||
}
|
||||
#endif
|
||||
|
||||
MENU_ITEM(submenu, MSG_MOVE_AXIS, lcd_move_menu);
|
||||
|
||||
#if defined(MANUAL_BED_LEVELING)
|
||||
|
|
@ -1338,7 +1342,7 @@ void lcd_update() {
|
|||
}
|
||||
|
||||
lastEncoderMovementMillis = ms;
|
||||
}
|
||||
} // encoderRateMultiplierEnabled
|
||||
#endif //ENCODER_RATE_MULTIPLIER
|
||||
|
||||
lcdDrawUpdate = 1;
|
||||
|
|
@ -1541,70 +1545,62 @@ bool lcd_clicked() { return LCD_CLICKED; }
|
|||
|
||||
#endif //ULTIPANEL
|
||||
|
||||
/********************************/
|
||||
/** Float conversion utilities **/
|
||||
/********************************/
|
||||
// convert float to string with +123.4 format
|
||||
/*********************************/
|
||||
/** Number to string conversion **/
|
||||
/*********************************/
|
||||
|
||||
char conv[8];
|
||||
char *ftostr3(const float &x)
|
||||
{
|
||||
|
||||
// Convert float to string with +123.4 format
|
||||
char *ftostr3(const float &x) {
|
||||
return itostr3((int)x);
|
||||
}
|
||||
|
||||
char *itostr2(const uint8_t &x)
|
||||
{
|
||||
// Convert int to string with 12 format
|
||||
char *itostr2(const uint8_t &x) {
|
||||
//sprintf(conv,"%5.1f",x);
|
||||
int xx=x;
|
||||
conv[0]=(xx/10)%10+'0';
|
||||
conv[1]=(xx)%10+'0';
|
||||
conv[2]=0;
|
||||
int xx = x;
|
||||
conv[0] = (xx / 10) % 10 + '0';
|
||||
conv[1] = xx % 10 + '0';
|
||||
conv[2] = 0;
|
||||
return conv;
|
||||
}
|
||||
|
||||
// Convert float to string with +123.4 format
|
||||
char *ftostr31(const float &x) {
|
||||
int xx = abs(x * 10);
|
||||
conv[0] = (x >= 0) ? '+' : '-';
|
||||
conv[1] = (xx / 1000) % 10 + '0';
|
||||
conv[2] = (xx / 100) % 10 + '0';
|
||||
conv[3] = (xx / 10) % 10 + '0';
|
||||
conv[4] = '.';
|
||||
conv[5] = xx % 10 + '0';
|
||||
conv[6] = 0;
|
||||
return conv;
|
||||
}
|
||||
|
||||
// Convert float to string with 123.4 format, dropping sign
|
||||
char *ftostr31(const float &x)
|
||||
{
|
||||
int xx=x*10;
|
||||
conv[0]=(xx>=0)?'+':'-';
|
||||
xx=abs(xx);
|
||||
conv[1]=(xx/1000)%10+'0';
|
||||
conv[2]=(xx/100)%10+'0';
|
||||
conv[3]=(xx/10)%10+'0';
|
||||
conv[4]='.';
|
||||
conv[5]=(xx)%10+'0';
|
||||
conv[6]=0;
|
||||
char *ftostr31ns(const float &x) {
|
||||
int xx = abs(x * 10);
|
||||
conv[0] = (xx / 1000) % 10 + '0';
|
||||
conv[1] = (xx / 100) % 10 + '0';
|
||||
conv[2] = (xx / 10) % 10 + '0';
|
||||
conv[3] = '.';
|
||||
conv[4] = xx % 10 + '0';
|
||||
conv[5] = 0;
|
||||
return conv;
|
||||
}
|
||||
|
||||
// Convert float to string with 123.4 format
|
||||
char *ftostr31ns(const float &x)
|
||||
{
|
||||
int xx=x*10;
|
||||
//conv[0]=(xx>=0)?'+':'-';
|
||||
xx=abs(xx);
|
||||
conv[0]=(xx/1000)%10+'0';
|
||||
conv[1]=(xx/100)%10+'0';
|
||||
conv[2]=(xx/10)%10+'0';
|
||||
conv[3]='.';
|
||||
conv[4]=(xx)%10+'0';
|
||||
conv[5]=0;
|
||||
return conv;
|
||||
}
|
||||
|
||||
char *ftostr32(const float &x)
|
||||
{
|
||||
long xx=x*100;
|
||||
if (xx >= 0)
|
||||
conv[0]=(xx/10000)%10+'0';
|
||||
else
|
||||
conv[0]='-';
|
||||
xx=abs(xx);
|
||||
conv[1]=(xx/1000)%10+'0';
|
||||
conv[2]=(xx/100)%10+'0';
|
||||
conv[3]='.';
|
||||
conv[4]=(xx/10)%10+'0';
|
||||
conv[5]=(xx)%10+'0';
|
||||
conv[6]=0;
|
||||
char *ftostr32(const float &x) {
|
||||
long xx = abs(x * 100);
|
||||
conv[0] = x >= 0 ? (xx / 10000) % 10 + '0' : '-';
|
||||
conv[1] = (xx / 1000) % 10 + '0';
|
||||
conv[2] = (xx / 100) % 10 + '0';
|
||||
conv[3] = '.';
|
||||
conv[4] = (xx / 10) % 10 + '0';
|
||||
conv[5] = xx % 10 + '0';
|
||||
conv[6] = 0;
|
||||
return conv;
|
||||
}
|
||||
|
||||
|
|
@ -1625,7 +1621,7 @@ char *ftostr43(const float &x)
|
|||
return conv;
|
||||
}
|
||||
|
||||
//Float to string with 1.23 format
|
||||
// Convert float to string with 1.23 format
|
||||
char *ftostr12ns(const float &x)
|
||||
{
|
||||
long xx=x*100;
|
||||
|
|
@ -1639,7 +1635,7 @@ char *ftostr12ns(const float &x)
|
|||
return conv;
|
||||
}
|
||||
|
||||
// convert float to space-padded string with -_23.4_ format
|
||||
// Convert float to space-padded string with -_23.4_ format
|
||||
char *ftostr32sp(const float &x) {
|
||||
long xx = abs(x * 100);
|
||||
uint8_t dig;
|
||||
|
|
@ -1685,58 +1681,51 @@ char *ftostr32sp(const float &x) {
|
|||
return conv;
|
||||
}
|
||||
|
||||
char *itostr31(const int &xx)
|
||||
{
|
||||
conv[0]=(xx>=0)?'+':'-';
|
||||
conv[1]=(xx/1000)%10+'0';
|
||||
conv[2]=(xx/100)%10+'0';
|
||||
conv[3]=(xx/10)%10+'0';
|
||||
conv[4]='.';
|
||||
conv[5]=(xx)%10+'0';
|
||||
conv[6]=0;
|
||||
// Convert int to lj string with +123.0 format
|
||||
char *itostr31(const int &x) {
|
||||
conv[0] = x >= 0 ? '+' : '-';
|
||||
int xx = abs(x);
|
||||
conv[1] = (xx / 100) % 10 + '0';
|
||||
conv[2] = (xx / 10) % 10 + '0';
|
||||
conv[3] = xx % 10 + '0';
|
||||
conv[4] = '.';
|
||||
conv[5] = '0';
|
||||
conv[6] = 0;
|
||||
return conv;
|
||||
}
|
||||
|
||||
// Convert int to rj string with 123 or -12 format
|
||||
char *itostr3(const int &x)
|
||||
{
|
||||
char *itostr3(const int &x) {
|
||||
int xx = x;
|
||||
if (xx < 0) {
|
||||
conv[0]='-';
|
||||
conv[0] = '-';
|
||||
xx = -xx;
|
||||
} else if (xx >= 100)
|
||||
conv[0]=(xx/100)%10+'0';
|
||||
}
|
||||
else
|
||||
conv[0]=' ';
|
||||
if (xx >= 10)
|
||||
conv[1]=(xx/10)%10+'0';
|
||||
else
|
||||
conv[1]=' ';
|
||||
conv[2]=(xx)%10+'0';
|
||||
conv[3]=0;
|
||||
conv[0] = xx >= 100 ? (xx / 100) % 10 + '0' : ' ';
|
||||
|
||||
conv[1] = xx >= 10 ? (xx / 10) % 10 + '0' : ' ';
|
||||
conv[2] = xx % 10 + '0';
|
||||
conv[3] = 0;
|
||||
return conv;
|
||||
}
|
||||
|
||||
// Convert int to lj string with 123 format
|
||||
char *itostr3left(const int &xx)
|
||||
{
|
||||
if (xx >= 100)
|
||||
{
|
||||
conv[0]=(xx/100)%10+'0';
|
||||
conv[1]=(xx/10)%10+'0';
|
||||
conv[2]=(xx)%10+'0';
|
||||
conv[3]=0;
|
||||
char *itostr3left(const int &xx) {
|
||||
if (xx >= 100) {
|
||||
conv[0] = (xx / 100) % 10 + '0';
|
||||
conv[1] = (xx / 10) % 10 + '0';
|
||||
conv[2] = xx % 10 + '0';
|
||||
conv[3] = 0;
|
||||
}
|
||||
else if (xx >= 10)
|
||||
{
|
||||
conv[0]=(xx/10)%10+'0';
|
||||
conv[1]=(xx)%10+'0';
|
||||
conv[2]=0;
|
||||
else if (xx >= 10) {
|
||||
conv[0] = (xx / 10) % 10 + '0';
|
||||
conv[1] = xx % 10 + '0';
|
||||
conv[2] = 0;
|
||||
}
|
||||
else
|
||||
{
|
||||
conv[0]=(xx)%10+'0';
|
||||
conv[1]=0;
|
||||
else {
|
||||
conv[0] = xx % 10 + '0';
|
||||
conv[1] = 0;
|
||||
}
|
||||
return conv;
|
||||
}
|
||||
|
|
@ -1764,34 +1753,30 @@ char *ftostr5(const float &x) {
|
|||
}
|
||||
|
||||
// Convert float to string with +1234.5 format
|
||||
char *ftostr51(const float &x)
|
||||
{
|
||||
long xx=x*10;
|
||||
conv[0]=(xx>=0)?'+':'-';
|
||||
xx=abs(xx);
|
||||
conv[1]=(xx/10000)%10+'0';
|
||||
conv[2]=(xx/1000)%10+'0';
|
||||
conv[3]=(xx/100)%10+'0';
|
||||
conv[4]=(xx/10)%10+'0';
|
||||
conv[5]='.';
|
||||
conv[6]=(xx)%10+'0';
|
||||
conv[7]=0;
|
||||
char *ftostr51(const float &x) {
|
||||
long xx = abs(x * 10);
|
||||
conv[0] = (x >= 0) ? '+' : '-';
|
||||
conv[1] = (xx / 10000) % 10 + '0';
|
||||
conv[2] = (xx / 1000) % 10 + '0';
|
||||
conv[3] = (xx / 100) % 10 + '0';
|
||||
conv[4] = (xx / 10) % 10 + '0';
|
||||
conv[5] = '.';
|
||||
conv[6] = xx % 10 + '0';
|
||||
conv[7] = 0;
|
||||
return conv;
|
||||
}
|
||||
|
||||
// Convert float to string with +123.45 format
|
||||
char *ftostr52(const float &x)
|
||||
{
|
||||
long xx=x*100;
|
||||
conv[0]=(xx>=0)?'+':'-';
|
||||
xx=abs(xx);
|
||||
conv[1]=(xx/10000)%10+'0';
|
||||
conv[2]=(xx/1000)%10+'0';
|
||||
conv[3]=(xx/100)%10+'0';
|
||||
conv[4]='.';
|
||||
conv[5]=(xx/10)%10+'0';
|
||||
conv[6]=(xx)%10+'0';
|
||||
conv[7]=0;
|
||||
char *ftostr52(const float &x) {
|
||||
conv[0] = (x >= 0) ? '+' : '-';
|
||||
long xx = abs(x * 100);
|
||||
conv[1] = (xx / 10000) % 10 + '0';
|
||||
conv[2] = (xx / 1000) % 10 + '0';
|
||||
conv[3] = (xx / 100) % 10 + '0';
|
||||
conv[4] = '.';
|
||||
conv[5] = (xx / 10) % 10 + '0';
|
||||
conv[6] = xx % 10 + '0';
|
||||
conv[7] = 0;
|
||||
return conv;
|
||||
}
|
||||
|
||||
|
|
|
|||
Loading…
Reference in a new issue