[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR (#10373)
This commit is contained in:
Eduardo José Tagle
Scott Lahteine
parent
5676b187b4
commit
57a899a412
|
|
@ -99,8 +99,6 @@
|
|||
#error "Z_ENDSTOP_SERVO_NR is now Z_PROBE_SERVO_NR. Please update your configuration."
|
||||
#elif defined(DEFAULT_XYJERK)
|
||||
#error "DEFAULT_XYJERK is deprecated. Use DEFAULT_XJERK and DEFAULT_YJERK instead."
|
||||
#elif ENABLED(BEZIER_JERK_CONTROL) && !defined(CPU_32_BIT)
|
||||
#error "BEZIER_JERK_CONTROL is computationally intensive and requires a 32-bit board."
|
||||
#elif defined(XY_TRAVEL_SPEED)
|
||||
#error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead."
|
||||
#elif defined(PROBE_SERVO_DEACTIVATION_DELAY)
|
||||
|
|
|
|||
|
|
@ -56,6 +56,10 @@
|
|||
*
|
||||
* IntersectionDistance[s1_, s2_, a_, d_] := (2 a d - s1^2 + s2^2)/(4 a)
|
||||
*
|
||||
* --
|
||||
*
|
||||
* The fast inverse function needed for Bézier interpolation for AVR
|
||||
* was designed, written and tested by Eduardo José Tagle on April/2018
|
||||
*/
|
||||
|
||||
#include "planner.h"
|
||||
|
|
@ -215,6 +219,523 @@ void Planner::init() {
|
|||
#endif
|
||||
}
|
||||
|
||||
#if ENABLED(BEZIER_JERK_CONTROL)
|
||||
|
||||
#ifdef __AVR__
|
||||
// This routine, for AVR, returns 0x1000000 / d, but trying to get the inverse as
|
||||
// fast as possible. A fast converging iterative Newton-Raphson method is able to
|
||||
// reach full precision in just 1 iteration, and takes 211 cycles (worst case, mean
|
||||
// case is less, up to 30 cycles for small divisors), instead of the 500 cycles a
|
||||
// normal division would take.
|
||||
//
|
||||
// Inspired by the following page,
|
||||
// https://stackoverflow.com/questions/27801397/newton-raphson-division-with-big-integers
|
||||
//
|
||||
// Suppose we want to calculate
|
||||
// floor(2 ^ k / B) where B is a positive integer
|
||||
// Then
|
||||
// B must be <= 2^k, otherwise, the quotient is 0.
|
||||
//
|
||||
// The Newton - Raphson iteration for x = B / 2 ^ k yields:
|
||||
// q[n + 1] = q[n] * (2 - q[n] * B / 2 ^ k)
|
||||
//
|
||||
// We can rearrange it as:
|
||||
// q[n + 1] = q[n] * (2 ^ (k + 1) - q[n] * B) >> k
|
||||
//
|
||||
// Each iteration of this kind requires only integer multiplications
|
||||
// and bit shifts.
|
||||
// Does it converge to floor(2 ^ k / B) ?: Not necessarily, but, in
|
||||
// the worst case, it eventually alternates between floor(2 ^ k / B)
|
||||
// and ceiling(2 ^ k / B)).
|
||||
// So we can use some not-so-clever test to see if we are in this
|
||||
// case, and extract floor(2 ^ k / B).
|
||||
// Lastly, a simple but important optimization for this approach is to
|
||||
// truncate multiplications (i.e.calculate only the higher bits of the
|
||||
// product) in the early iterations of the Newton - Raphson method.The
|
||||
// reason to do so, is that the results of the early iterations are far
|
||||
// from the quotient, and it doesn't matter to perform them inaccurately.
|
||||
// Finally, we should pick a good starting value for x. Knowing how many
|
||||
// digits the divisor has, we can estimate it:
|
||||
//
|
||||
// 2^k / x = 2 ^ log2(2^k / x)
|
||||
// 2^k / x = 2 ^(log2(2^k)-log2(x))
|
||||
// 2^k / x = 2 ^(k*log2(2)-log2(x))
|
||||
// 2^k / x = 2 ^ (k-log2(x))
|
||||
// 2^k / x >= 2 ^ (k-floor(log2(x)))
|
||||
// floor(log2(x)) simply is the index of the most significant bit set.
|
||||
//
|
||||
// If we could improve this estimation even further, then the number of
|
||||
// iterations can be dropped quite a bit, thus saving valuable execution time.
|
||||
// The paper "Software Integer Division" by Thomas L.Rodeheffer, Microsoft
|
||||
// Research, Silicon Valley,August 26, 2008, that is available at
|
||||
// https://www.microsoft.com/en-us/research/wp-content/uploads/2008/08/tr-2008-141.pdf
|
||||
// suggests , for its integer division algorithm, that using a table to supply the
|
||||
// first 8 bits of precision, and due to the quadratic convergence nature of the
|
||||
// Newton-Raphon iteration, then just 2 iterations should be enough to get
|
||||
// maximum precision of the division.
|
||||
// If we precompute values of inverses for small denominator values, then
|
||||
// just one Newton-Raphson iteration is enough to reach full precision
|
||||
// We will use the top 9 bits of the denominator as index.
|
||||
//
|
||||
// The AVR assembly function is implementing the following C code, included
|
||||
// here as reference:
|
||||
//
|
||||
// uint32_t get_period_inverse(uint32_t d) {
|
||||
// static const uint8_t inv_tab[256] = {
|
||||
// 255,253,252,250,248,246,244,242,240,238,236,234,233,231,229,227,
|
||||
// 225,224,222,220,218,217,215,213,212,210,208,207,205,203,202,200,
|
||||
// 199,197,195,194,192,191,189,188,186,185,183,182,180,179,178,176,
|
||||
// 175,173,172,170,169,168,166,165,164,162,161,160,158,157,156,154,
|
||||
// 153,152,151,149,148,147,146,144,143,142,141,139,138,137,136,135,
|
||||
// 134,132,131,130,129,128,127,126,125,123,122,121,120,119,118,117,
|
||||
// 116,115,114,113,112,111,110,109,108,107,106,105,104,103,102,101,
|
||||
// 100,99,98,97,96,95,94,93,92,91,90,89,88,88,87,86,
|
||||
// 85,84,83,82,81,80,80,79,78,77,76,75,74,74,73,72,
|
||||
// 71,70,70,69,68,67,66,66,65,64,63,62,62,61,60,59,
|
||||
// 59,58,57,56,56,55,54,53,53,52,51,50,50,49,48,48,
|
||||
// 47,46,46,45,44,43,43,42,41,41,40,39,39,38,37,37,
|
||||
// 36,35,35,34,33,33,32,32,31,30,30,29,28,28,27,27,
|
||||
// 26,25,25,24,24,23,22,22,21,21,20,19,19,18,18,17,
|
||||
// 17,16,15,15,14,14,13,13,12,12,11,10,10,9,9,8,
|
||||
// 8,7,7,6,6,5,5,4,4,3,3,2,2,1,0,0
|
||||
// };
|
||||
//
|
||||
// // For small denominators, it is cheaper to directly store the result,
|
||||
// // because those denominators would require 2 Newton-Raphson iterations
|
||||
// // to converge to the required result precision. For bigger ones, just
|
||||
// // ONE Newton-Raphson iteration is enough to get maximum precision!
|
||||
// static const uint32_t small_inv_tab[111] PROGMEM = {
|
||||
// 16777216,16777216,8388608,5592405,4194304,3355443,2796202,2396745,2097152,1864135,1677721,1525201,1398101,1290555,1198372,1118481,
|
||||
// 1048576,986895,932067,883011,838860,798915,762600,729444,699050,671088,645277,621378,599186,578524,559240,541200,
|
||||
// 524288,508400,493447,479349,466033,453438,441505,430185,419430,409200,399457,390167,381300,372827,364722,356962,
|
||||
// 349525,342392,335544,328965,322638,316551,310689,305040,299593,294337,289262,284359,279620,275036,270600,266305,
|
||||
// 262144,258111,254200,250406,246723,243148,239674,236298,233016,229824,226719,223696,220752,217885,215092,212369,
|
||||
// 209715,207126,204600,202135,199728,197379,195083,192841,190650,188508,186413,184365,182361,180400,178481,176602,
|
||||
// 174762,172960,171196,169466,167772,166111,164482,162885,161319,159783,158275,156796,155344,153919,152520
|
||||
// };
|
||||
//
|
||||
// // For small divisors, it is best to directly retrieve the results
|
||||
// if (d <= 110)
|
||||
// return pgm_read_dword(&small_inv_tab[d]);
|
||||
//
|
||||
// // Compute initial estimation of 0x1000000/x -
|
||||
// // Get most significant bit set on divider
|
||||
// uint8_t idx = 0;
|
||||
// uint32_t nr = d;
|
||||
// if (!(nr & 0xff0000)) {
|
||||
// nr <<= 8;
|
||||
// idx += 8;
|
||||
// if (!(nr & 0xff0000)) {
|
||||
// nr <<= 8;
|
||||
// idx += 8;
|
||||
// }
|
||||
// }
|
||||
// if (!(nr & 0xf00000)) {
|
||||
// nr <<= 4;
|
||||
// idx += 4;
|
||||
// }
|
||||
// if (!(nr & 0xc00000)) {
|
||||
// nr <<= 2;
|
||||
// idx += 2;
|
||||
// }
|
||||
// if (!(nr & 0x800000)) {
|
||||
// nr <<= 1;
|
||||
// idx += 1;
|
||||
// }
|
||||
//
|
||||
// // Isolate top 9 bits of the denominator, to be used as index into the initial estimation table
|
||||
// uint32_t tidx = nr >> 15; // top 9 bits. bit8 is always set
|
||||
// uint32_t ie = inv_tab[tidx & 0xFF] + 256; // Get the table value. bit9 is always set
|
||||
// uint32_t x = idx <= 8 ? (ie >> (8 - idx)) : (ie << (idx - 8)); // Position the estimation at the proper place
|
||||
//
|
||||
// // Now, refine estimation by newton-raphson. 1 iteration is enough
|
||||
// x = uint32_t((x * uint64_t((1 << 25) - x * d)) >> 24);
|
||||
//
|
||||
// // Estimate remainder
|
||||
// uint32_t r = (1 << 24) - x * d;
|
||||
//
|
||||
// // Check if we must adjust result
|
||||
// if (r >= d) x++;
|
||||
//
|
||||
// // x holds the proper estimation
|
||||
// return uint32_t(x);
|
||||
// }
|
||||
//
|
||||
static uint32_t get_period_inverse(uint32_t d) {
|
||||
|
||||
static const uint8_t inv_tab[256] PROGMEM = {
|
||||
255,253,252,250,248,246,244,242,240,238,236,234,233,231,229,227,
|
||||
225,224,222,220,218,217,215,213,212,210,208,207,205,203,202,200,
|
||||
199,197,195,194,192,191,189,188,186,185,183,182,180,179,178,176,
|
||||
175,173,172,170,169,168,166,165,164,162,161,160,158,157,156,154,
|
||||
153,152,151,149,148,147,146,144,143,142,141,139,138,137,136,135,
|
||||
134,132,131,130,129,128,127,126,125,123,122,121,120,119,118,117,
|
||||
116,115,114,113,112,111,110,109,108,107,106,105,104,103,102,101,
|
||||
100,99,98,97,96,95,94,93,92,91,90,89,88,88,87,86,
|
||||
85,84,83,82,81,80,80,79,78,77,76,75,74,74,73,72,
|
||||
71,70,70,69,68,67,66,66,65,64,63,62,62,61,60,59,
|
||||
59,58,57,56,56,55,54,53,53,52,51,50,50,49,48,48,
|
||||
47,46,46,45,44,43,43,42,41,41,40,39,39,38,37,37,
|
||||
36,35,35,34,33,33,32,32,31,30,30,29,28,28,27,27,
|
||||
26,25,25,24,24,23,22,22,21,21,20,19,19,18,18,17,
|
||||
17,16,15,15,14,14,13,13,12,12,11,10,10,9,9,8,
|
||||
8,7,7,6,6,5,5,4,4,3,3,2,2,1,0,0
|
||||
};
|
||||
|
||||
// For small denominators, it is cheaper to directly store the result.
|
||||
// For bigger ones, just ONE Newton-Raphson iteration is enough to get
|
||||
// maximum precision we need
|
||||
static const uint32_t small_inv_tab[111] PROGMEM = {
|
||||
16777216,16777216,8388608,5592405,4194304,3355443,2796202,2396745,2097152,1864135,1677721,1525201,1398101,1290555,1198372,1118481,
|
||||
1048576,986895,932067,883011,838860,798915,762600,729444,699050,671088,645277,621378,599186,578524,559240,541200,
|
||||
524288,508400,493447,479349,466033,453438,441505,430185,419430,409200,399457,390167,381300,372827,364722,356962,
|
||||
349525,342392,335544,328965,322638,316551,310689,305040,299593,294337,289262,284359,279620,275036,270600,266305,
|
||||
262144,258111,254200,250406,246723,243148,239674,236298,233016,229824,226719,223696,220752,217885,215092,212369,
|
||||
209715,207126,204600,202135,199728,197379,195083,192841,190650,188508,186413,184365,182361,180400,178481,176602,
|
||||
174762,172960,171196,169466,167772,166111,164482,162885,161319,159783,158275,156796,155344,153919,152520
|
||||
};
|
||||
|
||||
// For small divisors, it is best to directly retrieve the results
|
||||
if (d <= 110)
|
||||
return pgm_read_dword(&small_inv_tab[d]);
|
||||
|
||||
register uint8_t r8 = d & 0xFF;
|
||||
register uint8_t r9 = (d >> 8) & 0xFF;
|
||||
register uint8_t r10 = (d >> 16) & 0xFF;
|
||||
register uint8_t r2,r3,r4,r5,r6,r7,r11,r12,r13,r14,r15,r16,r17,r18;
|
||||
register const uint8_t* ptab = inv_tab;
|
||||
|
||||
__asm__ __volatile__(
|
||||
/* %8:%7:%6 = interval*/
|
||||
/* r31:r30: MUST be those registers, and they must point to the inv_tab */
|
||||
|
||||
" clr %13" "\n\t" /* %13 = 0 */
|
||||
|
||||
/* Now we must compute */
|
||||
/* result = 0xFFFFFF / d */
|
||||
/* %8:%7:%6 = interval*/
|
||||
/* %16:%15:%14 = nr */
|
||||
/* %13 = 0*/
|
||||
|
||||
/* A plain division of 24x24 bits should take 388 cycles to complete. We will */
|
||||
/* use Newton-Raphson for the calculation, and will strive to get way less cycles*/
|
||||
/* for the same result - Using C division, it takes 500cycles to complete .*/
|
||||
|
||||
" clr %3" "\n\t" /* idx = 0 */
|
||||
" mov %14,%6" "\n\t"
|
||||
" mov %15,%7" "\n\t"
|
||||
" mov %16,%8" "\n\t" /* nr = interval */
|
||||
" tst %16" "\n\t" /* nr & 0xFF0000 == 0 ? */
|
||||
" brne 2f" "\n\t" /* No, skip this */
|
||||
" mov %16,%15" "\n\t"
|
||||
" mov %15,%14" "\n\t" /* nr <<= 8, %14 not needed */
|
||||
" subi %3,-8" "\n\t" /* idx += 8 */
|
||||
" tst %16" "\n\t" /* nr & 0xFF0000 == 0 ? */
|
||||
" brne 2f" "\n\t" /* No, skip this */
|
||||
" mov %16,%15" "\n\t" /* nr <<= 8, %14 not needed */
|
||||
" clr %15" "\n\t" /* We clear %14 */
|
||||
" subi %3,-8" "\n\t" /* idx += 8 */
|
||||
|
||||
/* here %16 != 0 and %16:%15 contains at least 9 MSBits, or both %16:%15 are 0 */
|
||||
"2:" "\n\t"
|
||||
" cpi %16,0x10" "\n\t" /* (nr & 0xf00000) == 0 ? */
|
||||
" brcc 3f" "\n\t" /* No, skip this */
|
||||
" swap %15" "\n\t" /* Swap nibbles */
|
||||
" swap %16" "\n\t" /* Swap nibbles. Low nibble is 0 */
|
||||
" mov %14, %15" "\n\t"
|
||||
" andi %14,0x0f" "\n\t" /* Isolate low nibble */
|
||||
" andi %15,0xf0" "\n\t" /* Keep proper nibble in %15 */
|
||||
" or %16, %14" "\n\t" /* %16:%15 <<= 4 */
|
||||
" subi %3,-4" "\n\t" /* idx += 4 */
|
||||
|
||||
"3:" "\n\t"
|
||||
" cpi %16,0x40" "\n\t" /* (nr & 0xc00000) == 0 ? */
|
||||
" brcc 4f" "\n\t" /* No, skip this*/
|
||||
" add %15,%15" "\n\t"
|
||||
" adc %16,%16" "\n\t"
|
||||
" add %15,%15" "\n\t"
|
||||
" adc %16,%16" "\n\t" /* %16:%15 <<= 2 */
|
||||
" subi %3,-2" "\n\t" /* idx += 2 */
|
||||
|
||||
"4:" "\n\t"
|
||||
" cpi %16,0x80" "\n\t" /* (nr & 0x800000) == 0 ? */
|
||||
" brcc 5f" "\n\t" /* No, skip this */
|
||||
" add %15,%15" "\n\t"
|
||||
" adc %16,%16" "\n\t" /* %16:%15 <<= 1 */
|
||||
" inc %3" "\n\t" /* idx += 1 */
|
||||
|
||||
/* Now %16:%15 contains its MSBit set to 1, or %16:%15 is == 0. We are now absolutely sure*/
|
||||
/* we have at least 9 MSBits available to enter the initial estimation table*/
|
||||
"5:" "\n\t"
|
||||
" add %15,%15" "\n\t"
|
||||
" adc %16,%16" "\n\t" /* %16:%15 = tidx = (nr <<= 1), we lose the top MSBit (always set to 1, %16 is the index into the inverse table)*/
|
||||
" add r30,%16" "\n\t" /* Only use top 8 bits */
|
||||
" adc r31,%13" "\n\t" /* r31:r30 = inv_tab + (tidx) */
|
||||
" lpm %14, Z" "\n\t" /* %14 = inv_tab[tidx] */
|
||||
" ldi %15, 1" "\n\t" /* %15 = 1 %15:%14 = inv_tab[tidx] + 256 */
|
||||
|
||||
/* We must scale the approximation to the proper place*/
|
||||
" clr %16" "\n\t" /* %16 will always be 0 here */
|
||||
" subi %3,8" "\n\t" /* idx == 8 ? */
|
||||
" breq 6f" "\n\t" /* yes, no need to scale*/
|
||||
" brcs 7f" "\n\t" /* If C=1, means idx < 8, result was negative!*/
|
||||
|
||||
/* idx > 8, now %3 = idx - 8. We must perform a left shift. idx range:[1-8]*/
|
||||
" sbrs %3,0" "\n\t" /* shift by 1bit position?*/
|
||||
" rjmp 8f" "\n\t" /* No*/
|
||||
" add %14,%14" "\n\t"
|
||||
" adc %15,%15" "\n\t" /* %15:16 <<= 1*/
|
||||
"8:" "\n\t"
|
||||
" sbrs %3,1" "\n\t" /* shift by 2bit position?*/
|
||||
" rjmp 9f" "\n\t" /* No*/
|
||||
" add %14,%14" "\n\t"
|
||||
" adc %15,%15" "\n\t"
|
||||
" add %14,%14" "\n\t"
|
||||
" adc %15,%15" "\n\t" /* %15:16 <<= 1*/
|
||||
"9:" "\n\t"
|
||||
" sbrs %3,2" "\n\t" /* shift by 4bits position?*/
|
||||
" rjmp 16f" "\n\t" /* No*/
|
||||
" swap %15" "\n\t" /* Swap nibbles. lo nibble of %15 will always be 0*/
|
||||
" swap %14" "\n\t" /* Swap nibbles*/
|
||||
" mov %12,%14" "\n\t"
|
||||
" andi %12,0x0f" "\n\t" /* isolate low nibble*/
|
||||
" andi %14,0xf0" "\n\t" /* and clear it*/
|
||||
" or %15,%12" "\n\t" /* %15:%16 <<= 4*/
|
||||
"16:" "\n\t"
|
||||
" sbrs %3,3" "\n\t" /* shift by 8bits position?*/
|
||||
" rjmp 6f" "\n\t" /* No, we are done */
|
||||
" mov %16,%15" "\n\t"
|
||||
" mov %15,%14" "\n\t"
|
||||
" clr %14" "\n\t"
|
||||
" jmp 6f" "\n\t"
|
||||
|
||||
/* idx < 8, now %3 = idx - 8. Get the count of bits */
|
||||
"7:" "\n\t"
|
||||
" neg %3" "\n\t" /* %3 = -idx = count of bits to move right. idx range:[1...8]*/
|
||||
" sbrs %3,0" "\n\t" /* shift by 1 bit position ?*/
|
||||
" rjmp 10f" "\n\t" /* No, skip it*/
|
||||
" asr %15" "\n\t" /* (bit7 is always 0 here)*/
|
||||
" ror %14" "\n\t"
|
||||
"10:" "\n\t"
|
||||
" sbrs %3,1" "\n\t" /* shift by 2 bit position ?*/
|
||||
" rjmp 11f" "\n\t" /* No, skip it*/
|
||||
" asr %15" "\n\t" /* (bit7 is always 0 here)*/
|
||||
" ror %14" "\n\t"
|
||||
" asr %15" "\n\t" /* (bit7 is always 0 here)*/
|
||||
" ror %14" "\n\t"
|
||||
"11:" "\n\t"
|
||||
" sbrs %3,2" "\n\t" /* shift by 4 bit position ?*/
|
||||
" rjmp 12f" "\n\t" /* No, skip it*/
|
||||
" swap %15" "\n\t" /* Swap nibbles*/
|
||||
" andi %14, 0xf0" "\n\t" /* Lose the lowest nibble*/
|
||||
" swap %14" "\n\t" /* Swap nibbles. Upper nibble is 0*/
|
||||
" or %14,%15" "\n\t" /* Pass nibble from upper byte*/
|
||||
" andi %15, 0x0f" "\n\t" /* And get rid of that nibble*/
|
||||
"12:" "\n\t"
|
||||
" sbrs %3,3" "\n\t" /* shift by 8 bit position ?*/
|
||||
" rjmp 6f" "\n\t" /* No, skip it*/
|
||||
" mov %14,%15" "\n\t"
|
||||
" clr %15" "\n\t"
|
||||
"6:" "\n\t" /* %16:%15:%14 = initial estimation of 0x1000000 / d*/
|
||||
|
||||
/* Now, we must refine the estimation present on %16:%15:%14 using 1 iteration*/
|
||||
/* of Newton-Raphson. As it has a quadratic convergence, 1 iteration is enough*/
|
||||
/* to get more than 18bits of precision (the initial table lookup gives 9 bits of*/
|
||||
/* precision to start from). 18bits of precision is all what is needed here for result */
|
||||
|
||||
/* %8:%7:%6 = d = interval*/
|
||||
/* %16:%15:%14 = x = initial estimation of 0x1000000 / d*/
|
||||
/* %13 = 0*/
|
||||
/* %3:%2:%1:%0 = working accumulator*/
|
||||
|
||||
/* Compute 1<<25 - x*d. Result should never exceed 25 bits and should always be positive*/
|
||||
" clr %0" "\n\t"
|
||||
" clr %1" "\n\t"
|
||||
" clr %2" "\n\t"
|
||||
" ldi %3,2" "\n\t" /* %3:%2:%1:%0 = 0x2000000*/
|
||||
" mul %6,%14" "\n\t" /* r1:r0 = LO(d) * LO(x)*/
|
||||
" sub %0,r0" "\n\t"
|
||||
" sbc %1,r1" "\n\t"
|
||||
" sbc %2,%13" "\n\t"
|
||||
" sbc %3,%13" "\n\t" /* %3:%2:%1:%0 -= LO(d) * LO(x)*/
|
||||
" mul %7,%14" "\n\t" /* r1:r0 = MI(d) * LO(x)*/
|
||||
" sub %1,r0" "\n\t"
|
||||
" sbc %2,r1" "\n\t"
|
||||
" sbc %3,%13" "\n\t" /* %3:%2:%1:%0 -= MI(d) * LO(x) << 8*/
|
||||
" mul %8,%14" "\n\t" /* r1:r0 = HI(d) * LO(x)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t" /* %3:%2:%1:%0 -= MIL(d) * LO(x) << 16*/
|
||||
" mul %6,%15" "\n\t" /* r1:r0 = LO(d) * MI(x)*/
|
||||
" sub %1,r0" "\n\t"
|
||||
" sbc %2,r1" "\n\t"
|
||||
" sbc %3,%13" "\n\t" /* %3:%2:%1:%0 -= LO(d) * MI(x) << 8*/
|
||||
" mul %7,%15" "\n\t" /* r1:r0 = MI(d) * MI(x)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t" /* %3:%2:%1:%0 -= MI(d) * MI(x) << 16*/
|
||||
" mul %8,%15" "\n\t" /* r1:r0 = HI(d) * MI(x)*/
|
||||
" sub %3,r0" "\n\t" /* %3:%2:%1:%0 -= MIL(d) * MI(x) << 24*/
|
||||
" mul %6,%16" "\n\t" /* r1:r0 = LO(d) * HI(x)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t" /* %3:%2:%1:%0 -= LO(d) * HI(x) << 16*/
|
||||
" mul %7,%16" "\n\t" /* r1:r0 = MI(d) * HI(x)*/
|
||||
" sub %3,r0" "\n\t" /* %3:%2:%1:%0 -= MI(d) * HI(x) << 24*/
|
||||
/* %3:%2:%1:%0 = (1<<25) - x*d [169]*/
|
||||
|
||||
/* We need to multiply that result by x, and we are only interested in the top 24bits of that multiply*/
|
||||
|
||||
/* %16:%15:%14 = x = initial estimation of 0x1000000 / d*/
|
||||
/* %3:%2:%1:%0 = (1<<25) - x*d = acc*/
|
||||
/* %13 = 0 */
|
||||
|
||||
/* result = %11:%10:%9:%5:%4*/
|
||||
" mul %14,%0" "\n\t" /* r1:r0 = LO(x) * LO(acc)*/
|
||||
" mov %4,r1" "\n\t"
|
||||
" clr %5" "\n\t"
|
||||
" clr %9" "\n\t"
|
||||
" clr %10" "\n\t"
|
||||
" clr %11" "\n\t" /* %11:%10:%9:%5:%4 = LO(x) * LO(acc) >> 8*/
|
||||
" mul %15,%0" "\n\t" /* r1:r0 = MI(x) * LO(acc)*/
|
||||
" add %4,r0" "\n\t"
|
||||
" adc %5,r1" "\n\t"
|
||||
" adc %9,%13" "\n\t"
|
||||
" adc %10,%13" "\n\t"
|
||||
" adc %11,%13" "\n\t" /* %11:%10:%9:%5:%4 += MI(x) * LO(acc) */
|
||||
" mul %16,%0" "\n\t" /* r1:r0 = HI(x) * LO(acc)*/
|
||||
" add %5,r0" "\n\t"
|
||||
" adc %9,r1" "\n\t"
|
||||
" adc %10,%13" "\n\t"
|
||||
" adc %11,%13" "\n\t" /* %11:%10:%9:%5:%4 += MI(x) * LO(acc) << 8*/
|
||||
|
||||
" mul %14,%1" "\n\t" /* r1:r0 = LO(x) * MIL(acc)*/
|
||||
" add %4,r0" "\n\t"
|
||||
" adc %5,r1" "\n\t"
|
||||
" adc %9,%13" "\n\t"
|
||||
" adc %10,%13" "\n\t"
|
||||
" adc %11,%13" "\n\t" /* %11:%10:%9:%5:%4 = LO(x) * MIL(acc)*/
|
||||
" mul %15,%1" "\n\t" /* r1:r0 = MI(x) * MIL(acc)*/
|
||||
" add %5,r0" "\n\t"
|
||||
" adc %9,r1" "\n\t"
|
||||
" adc %10,%13" "\n\t"
|
||||
" adc %11,%13" "\n\t" /* %11:%10:%9:%5:%4 += MI(x) * MIL(acc) << 8*/
|
||||
" mul %16,%1" "\n\t" /* r1:r0 = HI(x) * MIL(acc)*/
|
||||
" add %9,r0" "\n\t"
|
||||
" adc %10,r1" "\n\t"
|
||||
" adc %11,%13" "\n\t" /* %11:%10:%9:%5:%4 += MI(x) * MIL(acc) << 16*/
|
||||
|
||||
" mul %14,%2" "\n\t" /* r1:r0 = LO(x) * MIH(acc)*/
|
||||
" add %5,r0" "\n\t"
|
||||
" adc %9,r1" "\n\t"
|
||||
" adc %10,%13" "\n\t"
|
||||
" adc %11,%13" "\n\t" /* %11:%10:%9:%5:%4 = LO(x) * MIH(acc) << 8*/
|
||||
" mul %15,%2" "\n\t" /* r1:r0 = MI(x) * MIH(acc)*/
|
||||
" add %9,r0" "\n\t"
|
||||
" adc %10,r1" "\n\t"
|
||||
" adc %11,%13" "\n\t" /* %11:%10:%9:%5:%4 += MI(x) * MIH(acc) << 16*/
|
||||
" mul %16,%2" "\n\t" /* r1:r0 = HI(x) * MIH(acc)*/
|
||||
" add %10,r0" "\n\t"
|
||||
" adc %11,r1" "\n\t" /* %11:%10:%9:%5:%4 += MI(x) * MIH(acc) << 24*/
|
||||
|
||||
" mul %14,%3" "\n\t" /* r1:r0 = LO(x) * HI(acc)*/
|
||||
" add %9,r0" "\n\t"
|
||||
" adc %10,r1" "\n\t"
|
||||
" adc %11,%13" "\n\t" /* %11:%10:%9:%5:%4 = LO(x) * HI(acc) << 16*/
|
||||
" mul %15,%3" "\n\t" /* r1:r0 = MI(x) * HI(acc)*/
|
||||
" add %10,r0" "\n\t"
|
||||
" adc %11,r1" "\n\t" /* %11:%10:%9:%5:%4 += MI(x) * HI(acc) << 24*/
|
||||
" mul %16,%3" "\n\t" /* r1:r0 = HI(x) * HI(acc)*/
|
||||
" add %11,r0" "\n\t" /* %11:%10:%9:%5:%4 += MI(x) * HI(acc) << 32*/
|
||||
|
||||
/* At this point, %11:%10:%9 contains the new estimation of x. */
|
||||
|
||||
/* Finally, we must correct the result. Estimate remainder as*/
|
||||
/* (1<<24) - x*d*/
|
||||
/* %11:%10:%9 = x*/
|
||||
/* %8:%7:%6 = d = interval" "\n\t" /* */
|
||||
" ldi %3,1" "\n\t"
|
||||
" clr %2" "\n\t"
|
||||
" clr %1" "\n\t"
|
||||
" clr %0" "\n\t" /* %3:%2:%1:%0 = 0x1000000*/
|
||||
" mul %6,%9" "\n\t" /* r1:r0 = LO(d) * LO(x)*/
|
||||
" sub %0,r0" "\n\t"
|
||||
" sbc %1,r1" "\n\t"
|
||||
" sbc %2,%13" "\n\t"
|
||||
" sbc %3,%13" "\n\t" /* %3:%2:%1:%0 -= LO(d) * LO(x)*/
|
||||
" mul %7,%9" "\n\t" /* r1:r0 = MI(d) * LO(x)*/
|
||||
" sub %1,r0" "\n\t"
|
||||
" sbc %2,r1" "\n\t"
|
||||
" sbc %3,%13" "\n\t" /* %3:%2:%1:%0 -= MI(d) * LO(x) << 8*/
|
||||
" mul %8,%9" "\n\t" /* r1:r0 = HI(d) * LO(x)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t" /* %3:%2:%1:%0 -= MIL(d) * LO(x) << 16*/
|
||||
" mul %6,%10" "\n\t" /* r1:r0 = LO(d) * MI(x)*/
|
||||
" sub %1,r0" "\n\t"
|
||||
" sbc %2,r1" "\n\t"
|
||||
" sbc %3,%13" "\n\t" /* %3:%2:%1:%0 -= LO(d) * MI(x) << 8*/
|
||||
" mul %7,%10" "\n\t" /* r1:r0 = MI(d) * MI(x)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t" /* %3:%2:%1:%0 -= MI(d) * MI(x) << 16*/
|
||||
" mul %8,%10" "\n\t" /* r1:r0 = HI(d) * MI(x)*/
|
||||
" sub %3,r0" "\n\t" /* %3:%2:%1:%0 -= MIL(d) * MI(x) << 24*/
|
||||
" mul %6,%11" "\n\t" /* r1:r0 = LO(d) * HI(x)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t" /* %3:%2:%1:%0 -= LO(d) * HI(x) << 16*/
|
||||
" mul %7,%11" "\n\t" /* r1:r0 = MI(d) * HI(x)*/
|
||||
" sub %3,r0" "\n\t" /* %3:%2:%1:%0 -= MI(d) * HI(x) << 24*/
|
||||
/* %3:%2:%1:%0 = r = (1<<24) - x*d*/
|
||||
/* %8:%7:%6 = d = interval */
|
||||
|
||||
/* Perform the final correction*/
|
||||
" sub %0,%6" "\n\t"
|
||||
" sbc %1,%7" "\n\t"
|
||||
" sbc %2,%8" "\n\t" /* r -= d*/
|
||||
" brcs 14f" "\n\t" /* if ( r >= d) */
|
||||
|
||||
/* %11:%10:%9 = x */
|
||||
" ldi %3,1" "\n\t"
|
||||
" add %9,%3" "\n\t"
|
||||
" adc %10,%13" "\n\t"
|
||||
" adc %11,%13" "\n\t" /* x++*/
|
||||
"14:" "\n\t"
|
||||
|
||||
/* Estimation is done. %11:%10:%9 = x */
|
||||
" clr __zero_reg__" "\n\t" /* Make C runtime happy */
|
||||
/* [211 cycles total]*/
|
||||
: "=r" (r2),
|
||||
"=r" (r3),
|
||||
"=r" (r4),
|
||||
"=d" (r5),
|
||||
"=r" (r6),
|
||||
"=r" (r7),
|
||||
"+r" (r8),
|
||||
"+r" (r9),
|
||||
"+r" (r10),
|
||||
"=d" (r11),
|
||||
"=r" (r12),
|
||||
"=r" (r13),
|
||||
"=d" (r14),
|
||||
"=d" (r15),
|
||||
"=d" (r16),
|
||||
"=d" (r17),
|
||||
"=d" (r18),
|
||||
"+z" (ptab)
|
||||
:
|
||||
: "r0", "r1", "cc"
|
||||
);
|
||||
|
||||
// Return the result
|
||||
return r11 | (uint16_t(r12) << 8) | (uint32_t(r13) << 16);
|
||||
}
|
||||
#else
|
||||
// All the other 32 CPUs can easily perform the inverse using hardware division,
|
||||
// so we don´t need to reduce precision or to use assembly language at all.
|
||||
|
||||
// This routine, for all the other archs, returns 0x100000000 / d ~= 0xFFFFFFFF / d
|
||||
static FORCE_INLINE uint32_t get_period_inverse(uint32_t d) {
|
||||
return 0xFFFFFFFF / d;
|
||||
}
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#define MINIMAL_STEP_RATE 120
|
||||
|
||||
/**
|
||||
|
|
@ -266,8 +787,13 @@ void Planner::calculate_trapezoid_for_block(block_t* const block, const float &e
|
|||
|
||||
#if ENABLED(BEZIER_JERK_CONTROL)
|
||||
// Jerk controlled speed requires to express speed versus time, NOT steps
|
||||
int32_t acceleration_time = ((float)(cruise_rate - initial_rate) / accel) * HAL_STEPPER_TIMER_RATE,
|
||||
deceleration_time = ((float)(cruise_rate - final_rate) / accel) * HAL_STEPPER_TIMER_RATE;
|
||||
uint32_t acceleration_time = ((float)(cruise_rate - initial_rate) / accel) * HAL_STEPPER_TIMER_RATE,
|
||||
deceleration_time = ((float)(cruise_rate - final_rate) / accel) * HAL_STEPPER_TIMER_RATE;
|
||||
|
||||
// And to offload calculations from the ISR, we also calculate the inverse of those times here
|
||||
uint32_t acceleration_time_inverse = get_period_inverse(acceleration_time);
|
||||
uint32_t deceleration_time_inverse = get_period_inverse(deceleration_time);
|
||||
|
||||
#endif
|
||||
|
||||
CRITICAL_SECTION_START; // Fill variables used by the stepper in a critical section
|
||||
|
|
@ -278,6 +804,8 @@ void Planner::calculate_trapezoid_for_block(block_t* const block, const float &e
|
|||
#if ENABLED(BEZIER_JERK_CONTROL)
|
||||
block->acceleration_time = acceleration_time;
|
||||
block->deceleration_time = deceleration_time;
|
||||
block->acceleration_time_inverse = acceleration_time_inverse;
|
||||
block->deceleration_time_inverse = deceleration_time_inverse;
|
||||
block->cruise_rate = cruise_rate;
|
||||
#endif
|
||||
block->final_rate = final_rate;
|
||||
|
|
|
|||
|
|
@ -96,8 +96,10 @@ typedef struct {
|
|||
|
||||
#if ENABLED(BEZIER_JERK_CONTROL)
|
||||
uint32_t cruise_rate; // The actual cruise rate to use, between end of the acceleration phase and start of deceleration phase
|
||||
int32_t acceleration_time, // Acceleration time and deceleration time in STEP timer counts
|
||||
deceleration_time;
|
||||
uint32_t acceleration_time, // Acceleration time and deceleration time in STEP timer counts
|
||||
deceleration_time;
|
||||
uint32_t acceleration_time_inverse, // Inverse of acceleration and deceleration periods, expressed as integer. Scale depends on CPU being used
|
||||
deceleration_time_inverse;
|
||||
#else
|
||||
int32_t acceleration_rate; // The acceleration rate used for acceleration calculation
|
||||
#endif
|
||||
|
|
|
|||
|
|
@ -117,11 +117,14 @@ long Stepper::counter_X = 0,
|
|||
volatile uint32_t Stepper::step_events_completed = 0; // The number of step events executed in the current block
|
||||
|
||||
#if ENABLED(BEZIER_JERK_CONTROL)
|
||||
int32_t Stepper::bezier_A, // A coefficient in Bézier speed curve
|
||||
Stepper::bezier_B, // B coefficient in Bézier speed curve
|
||||
Stepper::bezier_C, // C coefficient in Bézier speed curve
|
||||
Stepper::bezier_F; // F coefficient in Bézier speed curve
|
||||
uint32_t Stepper::bezier_AV; // AV coefficient in Bézier speed curve
|
||||
int32_t __attribute__((used)) Stepper::bezier_A __asm__("bezier_A"); // A coefficient in Bézier speed curve with alias for assembler
|
||||
int32_t __attribute__((used)) Stepper::bezier_B __asm__("bezier_B"); // B coefficient in Bézier speed curve with alias for assembler
|
||||
int32_t __attribute__((used)) Stepper::bezier_C __asm__("bezier_C"); // C coefficient in Bézier speed curve with alias for assembler
|
||||
uint32_t __attribute__((used)) Stepper::bezier_F __asm__("bezier_F"); // F coefficient in Bézier speed curve with alias for assembler
|
||||
uint32_t __attribute__((used)) Stepper::bezier_AV __asm__("bezier_AV"); // AV coefficient in Bézier speed curve with alias for assembler
|
||||
#ifdef __AVR__
|
||||
bool __attribute__((used)) Stepper::A_negative __asm__("A_negative"); // If A coefficient was negative
|
||||
#endif
|
||||
bool Stepper::bezier_2nd_half; // =false If Bézier curve has been initialized or not
|
||||
#endif
|
||||
|
||||
|
|
@ -391,130 +394,735 @@ void Stepper::set_directions() {
|
|||
*
|
||||
* Note the abbreviations we use in the following formulae are between []s
|
||||
*
|
||||
* At the start of each trapezoid, we calculate the coefficients A,B,C,F and Advance [AV], as follows:
|
||||
* For Any 32bit CPU:
|
||||
*
|
||||
* A = 6*128*(VF - VI) = 768*(VF - VI)
|
||||
* B = 15*128*(VI - VF) = 1920*(VI - VF)
|
||||
* C = 10*128*(VF - VI) = 1280*(VF - VI)
|
||||
* F = 128*VI = 128*VI
|
||||
* AV = (1<<32)/TS ~= 0xFFFFFFFF / TS (To use ARM UDIV, that is 32 bits)
|
||||
* At the start of each trapezoid, we calculate the coefficients A,B,C,F and Advance [AV], as follows:
|
||||
*
|
||||
* And for each point, we will evaluate the curve with the following sequence:
|
||||
* A = 6*128*(VF - VI) = 768*(VF - VI)
|
||||
* B = 15*128*(VI - VF) = 1920*(VI - VF)
|
||||
* C = 10*128*(VF - VI) = 1280*(VF - VI)
|
||||
* F = 128*VI = 128*VI
|
||||
* AV = (1<<32)/TS ~= 0xFFFFFFFF / TS (To use ARM UDIV, that is 32 bits) (this is computed at the planner, to offload expensive calculations from the ISR)
|
||||
*
|
||||
* uint32_t t = bezier_AV * curr_step; // t: Range 0 - 1^32 = 32 bits
|
||||
* uint64_t f = t;
|
||||
* f *= t; // Range 32*2 = 64 bits (unsigned)
|
||||
* f >>= 32; // Range 32 bits (unsigned)
|
||||
* f *= t; // Range 32*2 = 64 bits (unsigned)
|
||||
* f >>= 32; // Range 32 bits : f = t^3 (unsigned)
|
||||
* int64_t acc = (int64_t) bezier_F << 31; // Range 63 bits (signed)
|
||||
* acc += ((uint32_t) f >> 1) * (int64_t) bezier_C; // Range 29bits + 31 = 60bits (plus sign)
|
||||
* f *= t; // Range 32*2 = 64 bits
|
||||
* f >>= 32; // Range 32 bits : f = t^3 (unsigned)
|
||||
* acc += ((uint32_t) f >> 1) * (int64_t) bezier_B; // Range 29bits + 31 = 60bits (plus sign)
|
||||
* f *= t; // Range 32*2 = 64 bits
|
||||
* f >>= 32; // Range 32 bits : f = t^3 (unsigned)
|
||||
* acc += ((uint32_t) f >> 1) * (int64_t) bezier_A; // Range 28bits + 31 = 59bits (plus sign)
|
||||
* acc >>= (31 + 7); // Range 24bits (plus sign)
|
||||
* And for each point, we will evaluate the curve with the following sequence:
|
||||
*
|
||||
* This can be translated to the following ARM assembly sequence:
|
||||
* void lsrs(uint32_t& d, uint32_t s, int cnt) {
|
||||
* d = s >> cnt;
|
||||
* }
|
||||
* void lsls(uint32_t& d, uint32_t s, int cnt) {
|
||||
* d = s << cnt;
|
||||
* }
|
||||
* void lsrs(int32_t& d, uint32_t s, int cnt) {
|
||||
* d = uint32_t(s) >> cnt;
|
||||
* }
|
||||
* void lsls(int32_t& d, uint32_t s, int cnt) {
|
||||
* d = uint32_t(s) << cnt;
|
||||
* }
|
||||
* void umull(uint32_t& rlo, uint32_t& rhi, uint32_t op1, uint32_t op2) {
|
||||
* uint64_t res = uint64_t(op1) * op2;
|
||||
* rlo = uint32_t(res & 0xFFFFFFFF);
|
||||
* rhi = uint32_t((res >> 32) & 0xFFFFFFFF);
|
||||
* }
|
||||
* void smlal(int32_t& rlo, int32_t& rhi, int32_t op1, int32_t op2) {
|
||||
* int64_t mul = int64_t(op1) * op2;
|
||||
* int64_t s = int64_t(uint32_t(rlo) | ((uint64_t(uint32_t(rhi)) << 32U)));
|
||||
* mul += s;
|
||||
* rlo = int32_t(mul & 0xFFFFFFFF);
|
||||
* rhi = int32_t((mul >> 32) & 0xFFFFFFFF);
|
||||
* }
|
||||
* int32_t _eval_bezier_curve_arm(uint32_t curr_step) {
|
||||
* register uint32_t flo = 0;
|
||||
* register uint32_t fhi = bezier_AV * curr_step;
|
||||
* register uint32_t t = fhi;
|
||||
* register int32_t alo = bezier_F;
|
||||
* register int32_t ahi = 0;
|
||||
* register int32_t A = bezier_A;
|
||||
* register int32_t B = bezier_B;
|
||||
* register int32_t C = bezier_C;
|
||||
*
|
||||
* At start:
|
||||
* fhi = AV, flo = CS, alo = F
|
||||
* lsrs(ahi, alo, 1); // a = F << 31
|
||||
* lsls(alo, alo, 31); //
|
||||
* umull(flo, fhi, fhi, t); // f *= t
|
||||
* umull(flo, fhi, fhi, t); // f>>=32; f*=t
|
||||
* lsrs(flo, fhi, 1); //
|
||||
* smlal(alo, ahi, flo, C); // a+=(f>>33)*C
|
||||
* umull(flo, fhi, fhi, t); // f>>=32; f*=t
|
||||
* lsrs(flo, fhi, 1); //
|
||||
* smlal(alo, ahi, flo, B); // a+=(f>>33)*B
|
||||
* umull(flo, fhi, fhi, t); // f>>=32; f*=t
|
||||
* lsrs(flo, fhi, 1); // f>>=33;
|
||||
* smlal(alo, ahi, flo, A); // a+=(f>>33)*A;
|
||||
* lsrs(alo, ahi, 6); // a>>=38
|
||||
*
|
||||
* return alo;
|
||||
* }
|
||||
*
|
||||
* This will be rewritten in ARM assembly to get peak performance and will take 43 cycles to execute
|
||||
*
|
||||
* For AVR, we scale precision of coefficients to make it possible to evaluate the Bézier curve in
|
||||
* realtime: Let's reduce precision as much as possible. After some experimentation we found that:
|
||||
*
|
||||
* Assume t and AV with 24 bits is enough
|
||||
* A = 6*(VF - VI)
|
||||
* B = 15*(VI - VF)
|
||||
* C = 10*(VF - VI)
|
||||
* F = VI
|
||||
* AV = (1<<24)/TS (this is computed at the planner, to offload expensive calculations from the ISR)
|
||||
*
|
||||
* Instead of storing sign for each coefficient, we will store its absolute value,
|
||||
* and flag the sign of the A coefficient, so we can save to store the sign bit.
|
||||
* It always holds that sign(A) = - sign(B) = sign(C)
|
||||
*
|
||||
* So, the resulting range of the coefficients are:
|
||||
*
|
||||
* t: unsigned (0 <= t < 1) |range 0 to 0xFFFFFF unsigned
|
||||
* A: signed Q24 , range = 250000 * 6 = 1500000 = 0x16E360 | 21 bits
|
||||
* B: signed Q24 , range = 250000 *15 = 3750000 = 0x393870 | 22 bits
|
||||
* C: signed Q24 , range = 250000 *10 = 2500000 = 0x1312D0 | 21 bits
|
||||
* F: signed Q24 , range = 250000 = 250000 = 0x0ED090 | 20 bits
|
||||
*
|
||||
* And for each curve, we estimate its coefficients with:
|
||||
*
|
||||
* void _calc_bezier_curve_coeffs(int32_t v0, int32_t v1, uint32_t av) {
|
||||
* // Calculate the Bézier coefficients
|
||||
* if (v1 < v0) {
|
||||
* A_negative = true;
|
||||
* bezier_A = 6 * (v0 - v1);
|
||||
* bezier_B = 15 * (v0 - v1);
|
||||
* bezier_C = 10 * (v0 - v1);
|
||||
* }
|
||||
* else {
|
||||
* A_negative = false;
|
||||
* bezier_A = 6 * (v1 - v0);
|
||||
* bezier_B = 15 * (v1 - v0);
|
||||
* bezier_C = 10 * (v1 - v0);
|
||||
* }
|
||||
* bezier_F = v0;
|
||||
* }
|
||||
*
|
||||
* And for each point, we will evaluate the curve with the following sequence:
|
||||
*
|
||||
* // unsigned multiplication of 24 bits x 24bits, return upper 16 bits
|
||||
* void umul24x24to16hi(uint16_t& r, uint24_t op1, uint24_t op2) {
|
||||
* r = (uint64_t(op1) * op2) >> 8;
|
||||
* }
|
||||
* // unsigned multiplication of 16 bits x 16bits, return upper 16 bits
|
||||
* void umul16x16to16hi(uint16_t& r, uint16_t op1, uint16_t op2) {
|
||||
* r = (uint32_t(op1) * op2) >> 16;
|
||||
* }
|
||||
* // unsigned multiplication of 16 bits x 24bits, return upper 24 bits
|
||||
* void umul16x24to24hi(uint24_t& r, uint16_t op1, uint24_t op2) {
|
||||
* r = uint24_t((uint64_t(op1) * op2) >> 16);
|
||||
* }
|
||||
*
|
||||
* int32_t _eval_bezier_curve(uint32_t curr_step) {
|
||||
* // To save computing, the first step is always the initial speed
|
||||
* if (!curr_step)
|
||||
* return bezier_F;
|
||||
*
|
||||
* uint16_t t;
|
||||
* umul24x24to16hi(t, bezier_AV, curr_step); // t: Range 0 - 1^16 = 16 bits
|
||||
* uint16_t f = t;
|
||||
* umul16x16to16hi(f, f, t); // Range 16 bits (unsigned)
|
||||
* umul16x16to16hi(f, f, t); // Range 16 bits : f = t^3 (unsigned)
|
||||
* uint24_t acc = bezier_F; // Range 20 bits (unsigned)
|
||||
* if (A_negative) {
|
||||
* uint24_t v;
|
||||
* umul16x24to24hi(v, f, bezier_C); // Range 21bits
|
||||
* acc -= v;
|
||||
* umul16x16to16hi(f, f, t); // Range 16 bits : f = t^4 (unsigned)
|
||||
* umul16x24to24hi(v, f, bezier_B); // Range 22bits
|
||||
* acc += v;
|
||||
* umul16x16to16hi(f, f, t); // Range 16 bits : f = t^5 (unsigned)
|
||||
* umul16x24to24hi(v, f, bezier_A); // Range 21bits + 15 = 36bits (plus sign)
|
||||
* acc -= v;
|
||||
* }
|
||||
* else {
|
||||
* uint24_t v;
|
||||
* umul16x24to24hi(v, f, bezier_C); // Range 21bits
|
||||
* acc += v;
|
||||
* umul16x16to16hi(f, f, t); // Range 16 bits : f = t^4 (unsigned)
|
||||
* umul16x24to24hi(v, f, bezier_B); // Range 22bits
|
||||
* acc -= v;
|
||||
* umul16x16to16hi(f, f, t); // Range 16 bits : f = t^5 (unsigned)
|
||||
* umul16x24to24hi(v, f, bezier_A); // Range 21bits + 15 = 36bits (plus sign)
|
||||
* acc += v;
|
||||
* }
|
||||
* return acc;
|
||||
* }
|
||||
* Those functions will be translated into assembler to get peak performance. coefficient calculations takes 70 cycles,
|
||||
* Bezier point evaluation takes 150 cycles
|
||||
*
|
||||
* muls fhi,flo | f = AV * CS 1 cycles
|
||||
* mov t,fhi | t = AV * CS 1 cycles
|
||||
* lsrs ahi,alo,#1 | a = F << 31 1 cycles
|
||||
* lsls alo,alo,#31 | 1 cycles
|
||||
* umull flo,fhi,fhi,t | f *= t 5 cycles [fhi:flo=64bits
|
||||
* umull flo,fhi,fhi,t | f>>=32; f*=t 5 cycles [fhi:flo=64bits
|
||||
* lsrs flo,fhi,#1 | 1 cycles [31bits
|
||||
* smlal alo,ahi,flo,C | a+=(f>>33)*C; 5 cycles
|
||||
* umull flo,fhi,fhi,t | f>>=32; f*=t 5 cycles [fhi:flo=64bits
|
||||
* lsrs flo,fhi,#1 | 1 cycles [31bits
|
||||
* smlal alo,ahi,flo,B | a+=(f>>33)*B; 5 cycles
|
||||
* umull flo,fhi,fhi,t | f>>=32; f*=t 5 cycles [fhi:flo=64bits
|
||||
* lsrs flo,fhi,#1 | f>>=33; 1 cycles [31bits
|
||||
* smlal alo,ahi,flo,A | a+=(f>>33)*A; 5 cycles
|
||||
* lsrs alo,ahi,#6 | a>>=38 1 cycles
|
||||
* 43 cycles total
|
||||
*/
|
||||
|
||||
FORCE_INLINE void Stepper::_calc_bezier_curve_coeffs(const int32_t v0, const int32_t v1, const uint32_t interval) {
|
||||
// Calculate the Bézier coefficients
|
||||
bezier_A = 768 * (v1 - v0);
|
||||
bezier_B = 1920 * (v0 - v1);
|
||||
bezier_C = 1280 * (v1 - v0);
|
||||
bezier_F = 128 * v0;
|
||||
bezier_AV = 0xFFFFFFFF / interval;
|
||||
}
|
||||
#ifdef __AVR__
|
||||
|
||||
FORCE_INLINE int32_t Stepper::_eval_bezier_curve(const uint32_t curr_step) {
|
||||
#if defined(__ARM__) || defined(__thumb__)
|
||||
// For AVR we use assembly to maximize speed
|
||||
void Stepper::_calc_bezier_curve_coeffs(const int32_t v0, const int32_t v1, const uint32_t av) {
|
||||
|
||||
// For ARM CORTEX M3/M4 CPUs, we have the optimized assembler version, that takes 43 cycles to execute
|
||||
register uint32_t flo = 0;
|
||||
register uint32_t fhi = bezier_AV * curr_step;
|
||||
register uint32_t t = fhi;
|
||||
register int32_t alo = bezier_F;
|
||||
register int32_t ahi = 0;
|
||||
register int32_t A = bezier_A;
|
||||
register int32_t B = bezier_B;
|
||||
register int32_t C = bezier_C;
|
||||
// Store advance
|
||||
bezier_AV = av;
|
||||
|
||||
__asm__ __volatile__(
|
||||
".syntax unified" "\n\t" // is to prevent CM0,CM1 non-unified syntax
|
||||
" lsrs %[ahi],%[alo],#1" "\n\t" // a = F << 31 1 cycles
|
||||
" lsls %[alo],%[alo],#31" "\n\t" // 1 cycles
|
||||
" umull %[flo],%[fhi],%[fhi],%[t]" "\n\t" // f *= t 5 cycles [fhi:flo=64bits]
|
||||
" umull %[flo],%[fhi],%[fhi],%[t]" "\n\t" // f>>=32; f*=t 5 cycles [fhi:flo=64bits]
|
||||
" lsrs %[flo],%[fhi],#1" "\n\t" // 1 cycles [31bits]
|
||||
" smlal %[alo],%[ahi],%[flo],%[C]" "\n\t" // a+=(f>>33)*C; 5 cycles
|
||||
" umull %[flo],%[fhi],%[fhi],%[t]" "\n\t" // f>>=32; f*=t 5 cycles [fhi:flo=64bits]
|
||||
" lsrs %[flo],%[fhi],#1" "\n\t" // 1 cycles [31bits]
|
||||
" smlal %[alo],%[ahi],%[flo],%[B]" "\n\t" // a+=(f>>33)*B; 5 cycles
|
||||
" umull %[flo],%[fhi],%[fhi],%[t]" "\n\t" // f>>=32; f*=t 5 cycles [fhi:flo=64bits]
|
||||
" lsrs %[flo],%[fhi],#1" "\n\t" // f>>=33; 1 cycles [31bits]
|
||||
" smlal %[alo],%[ahi],%[flo],%[A]" "\n\t" // a+=(f>>33)*A; 5 cycles
|
||||
" lsrs %[alo],%[ahi],#6" "\n\t" // a>>=38 1 cycles
|
||||
: [alo]"+r"( alo ) ,
|
||||
[flo]"+r"( flo ) ,
|
||||
[fhi]"+r"( fhi ) ,
|
||||
[ahi]"+r"( ahi ) ,
|
||||
[A]"+r"( A ) , // <== Note: Even if A, B, C, and t registers are INPUT ONLY
|
||||
[B]"+r"( B ) , // GCC does bad optimizations on the code if we list them as
|
||||
[C]"+r"( C ) , // such, breaking this function. So, to avoid that problem,
|
||||
[t]"+r"( t ) // we list all registers as input-outputs.
|
||||
// Calculate the rest of the coefficients
|
||||
register uint8_t r2 = v0 & 0xFF;
|
||||
register uint8_t r3 = (v0 >> 8) & 0xFF;
|
||||
register uint8_t r12 = (v0 >> 16) & 0xFF;
|
||||
register uint8_t r5 = v1 & 0xFF;
|
||||
register uint8_t r6 = (v1 >> 8) & 0xFF;
|
||||
register uint8_t r7 = (v1 >> 16) & 0xFF;
|
||||
register uint8_t r4,r8,r9,r10,r11;
|
||||
|
||||
__asm__ __volatile__(
|
||||
/* Calculate the Bézier coefficients */
|
||||
/* %10:%1:%0 = v0*/
|
||||
/* %5:%4:%3 = v1*/
|
||||
/* %7:%6:%10 = temporary*/
|
||||
/* %9 = val (must be high register!)*/
|
||||
/* %10 (must be high register!)*/
|
||||
|
||||
/* Store initial velocity*/
|
||||
" sts bezier_F, %0" "\n\t"
|
||||
" sts bezier_F+1, %1" "\n\t"
|
||||
" sts bezier_F+2, %10" "\n\t" /* bezier_F = %10:%1:%0 = v0 */
|
||||
|
||||
/* Get delta speed */
|
||||
" ldi %2,-1" "\n\t" /* %2 = 0xff, means A_negative = true */
|
||||
" clr %8" "\n\t" /* %8 = 0 */
|
||||
" sub %0,%3" "\n\t"
|
||||
" sbc %1,%4" "\n\t"
|
||||
" sbc %10,%5" "\n\t" /* v0 -= v1, C=1 if result is negative */
|
||||
" brcc 1f" "\n\t" /* branch if result is positive (C=0), that means v0 >= v1 */
|
||||
|
||||
/* Result was negative, get the absolute value*/
|
||||
" com %10" "\n\t"
|
||||
" com %1" "\n\t"
|
||||
" neg %0" "\n\t"
|
||||
" sbc %1,%2" "\n\t"
|
||||
" sbc %10,%2" "\n\t" /* %10:%1:%0 +1 -> %10:%1:%0 = -(v0 - v1) = (v1 - v0) */
|
||||
" clr %2" "\n\t" /* %2 = 0, means A_negative = false */
|
||||
|
||||
/* Store negative flag*/
|
||||
"1:" "\n\t"
|
||||
" sts A_negative, %2" "\n\t" /* Store negative flag */
|
||||
|
||||
/* Compute coefficients A,B and C [20 cycles worst case]*/
|
||||
" ldi %9,6" "\n\t" /* %9 = 6 */
|
||||
" mul %0,%9" "\n\t" /* r1:r0 = 6*LO(v0-v1) */
|
||||
" sts bezier_A, r0" "\n\t"
|
||||
" mov %6,r1" "\n\t"
|
||||
" clr %7" "\n\t" /* %7:%6:r0 = 6*LO(v0-v1) */
|
||||
" mul %1,%9" "\n\t" /* r1:r0 = 6*MI(v0-v1) */
|
||||
" add %6,r0" "\n\t"
|
||||
" adc %7,r1" "\n\t" /* %7:%6:?? += 6*MI(v0-v1) << 8 */
|
||||
" mul %10,%9" "\n\t" /* r1:r0 = 6*HI(v0-v1) */
|
||||
" add %7,r0" "\n\t" /* %7:%6:?? += 6*HI(v0-v1) << 16 */
|
||||
" sts bezier_A+1, %6" "\n\t"
|
||||
" sts bezier_A+2, %7" "\n\t" /* bezier_A = %7:%6:?? = 6*(v0-v1) [35 cycles worst] */
|
||||
|
||||
" ldi %9,15" "\n\t" /* %9 = 15 */
|
||||
" mul %0,%9" "\n\t" /* r1:r0 = 5*LO(v0-v1) */
|
||||
" sts bezier_B, r0" "\n\t"
|
||||
" mov %6,r1" "\n\t"
|
||||
" clr %7" "\n\t" /* %7:%6:?? = 5*LO(v0-v1) */
|
||||
" mul %1,%9" "\n\t" /* r1:r0 = 5*MI(v0-v1) */
|
||||
" add %6,r0" "\n\t"
|
||||
" adc %7,r1" "\n\t" /* %7:%6:?? += 5*MI(v0-v1) << 8 */
|
||||
" mul %10,%9" "\n\t" /* r1:r0 = 5*HI(v0-v1) */
|
||||
" add %7,r0" "\n\t" /* %7:%6:?? += 5*HI(v0-v1) << 16 */
|
||||
" sts bezier_B+1, %6" "\n\t"
|
||||
" sts bezier_B+2, %7" "\n\t" /* bezier_B = %7:%6:?? = 5*(v0-v1) [50 cycles worst] */
|
||||
|
||||
" ldi %9,10" "\n\t" /* %9 = 10 */
|
||||
" mul %0,%9" "\n\t" /* r1:r0 = 10*LO(v0-v1) */
|
||||
" sts bezier_C, r0" "\n\t"
|
||||
" mov %6,r1" "\n\t"
|
||||
" clr %7" "\n\t" /* %7:%6:?? = 10*LO(v0-v1) */
|
||||
" mul %1,%9" "\n\t" /* r1:r0 = 10*MI(v0-v1) */
|
||||
" add %6,r0" "\n\t"
|
||||
" adc %7,r1" "\n\t" /* %7:%6:?? += 10*MI(v0-v1) << 8 */
|
||||
" mul %10,%9" "\n\t" /* r1:r0 = 10*HI(v0-v1) */
|
||||
" add %7,r0" "\n\t" /* %7:%6:?? += 10*HI(v0-v1) << 16 */
|
||||
" sts bezier_C+1, %6" "\n\t"
|
||||
" sts bezier_C+2, %7" /* bezier_C = %7:%6:?? = 10*(v0-v1) [65 cycles worst] */
|
||||
: "+r" (r2),
|
||||
"+d" (r3),
|
||||
"=r" (r4),
|
||||
"+r" (r5),
|
||||
"+r" (r6),
|
||||
"+r" (r7),
|
||||
"=r" (r8),
|
||||
"=r" (r9),
|
||||
"=r" (r10),
|
||||
"=d" (r11),
|
||||
"+r" (r12)
|
||||
:
|
||||
: "cc"
|
||||
: "r0", "r1", "cc", "memory"
|
||||
);
|
||||
return alo;
|
||||
}
|
||||
|
||||
#else
|
||||
FORCE_INLINE int32_t Stepper::_eval_bezier_curve(const uint32_t curr_step) {
|
||||
|
||||
// For non ARM targets, we provide a fallback implementation. Really doubt it
|
||||
// will be useful, unless the processor is extremely fast.
|
||||
// If dealing with the first step, save expensive computing and return the initial speed
|
||||
if (!curr_step)
|
||||
return bezier_F;
|
||||
|
||||
uint32_t t = bezier_AV * curr_step; // t: Range 0 - 1^32 = 32 bits
|
||||
uint64_t f = t;
|
||||
f *= t; // Range 32*2 = 64 bits (unsigned)
|
||||
f >>= 32; // Range 32 bits (unsigned)
|
||||
f *= t; // Range 32*2 = 64 bits (unsigned)
|
||||
f >>= 32; // Range 32 bits : f = t^3 (unsigned)
|
||||
int64_t acc = (int64_t) bezier_F << 31; // Range 63 bits (signed)
|
||||
acc += ((uint32_t) f >> 1) * (int64_t) bezier_C; // Range 29bits + 31 = 60bits (plus sign)
|
||||
f *= t; // Range 32*2 = 64 bits
|
||||
f >>= 32; // Range 32 bits : f = t^3 (unsigned)
|
||||
acc += ((uint32_t) f >> 1) * (int64_t) bezier_B; // Range 29bits + 31 = 60bits (plus sign)
|
||||
f *= t; // Range 32*2 = 64 bits
|
||||
f >>= 32; // Range 32 bits : f = t^3 (unsigned)
|
||||
acc += ((uint32_t) f >> 1) * (int64_t) bezier_A; // Range 28bits + 31 = 59bits (plus sign)
|
||||
acc >>= (31 + 7); // Range 24bits (plus sign)
|
||||
return (int32_t) acc;
|
||||
register uint8_t r0 = 0; /* Zero register */
|
||||
register uint8_t r2 = (curr_step) & 0xFF;
|
||||
register uint8_t r3 = (curr_step >> 8) & 0xFF;
|
||||
register uint8_t r4 = (curr_step >> 16) & 0xFF;
|
||||
register uint8_t r1,r5,r6,r7,r8,r9,r10,r11; /* Temporary registers */
|
||||
|
||||
#endif
|
||||
}
|
||||
__asm__ __volatile(
|
||||
/* umul24x24to16hi(t, bezier_AV, curr_step); t: Range 0 - 1^16 = 16 bits*/
|
||||
" lds %9,bezier_AV" "\n\t" /* %9 = LO(AV)*/
|
||||
" mul %9,%2" "\n\t" /* r1:r0 = LO(bezier_AV)*LO(curr_step)*/
|
||||
" mov %7,r1" "\n\t" /* %7 = LO(bezier_AV)*LO(curr_step) >> 8*/
|
||||
" clr %8" "\n\t" /* %8:%7 = LO(bezier_AV)*LO(curr_step) >> 8*/
|
||||
" lds %10,bezier_AV+1" "\n\t" /* %10 = MI(AV)*/
|
||||
" mul %10,%2" "\n\t" /* r1:r0 = MI(bezier_AV)*LO(curr_step)*/
|
||||
" add %7,r0" "\n\t"
|
||||
" adc %8,r1" "\n\t" /* %8:%7 += MI(bezier_AV)*LO(curr_step)*/
|
||||
" lds r1,bezier_AV+2" "\n\t" /* r11 = HI(AV)*/
|
||||
" mul r1,%2" "\n\t" /* r1:r0 = HI(bezier_AV)*LO(curr_step)*/
|
||||
" add %8,r0" "\n\t" /* %8:%7 += HI(bezier_AV)*LO(curr_step) << 8*/
|
||||
" mul %9,%3" "\n\t" /* r1:r0 = LO(bezier_AV)*MI(curr_step)*/
|
||||
" add %7,r0" "\n\t"
|
||||
" adc %8,r1" "\n\t" /* %8:%7 += LO(bezier_AV)*MI(curr_step)*/
|
||||
" mul %10,%3" "\n\t" /* r1:r0 = MI(bezier_AV)*MI(curr_step)*/
|
||||
" add %8,r0" "\n\t" /* %8:%7 += LO(bezier_AV)*MI(curr_step) << 8*/
|
||||
" mul %9,%4" "\n\t" /* r1:r0 = LO(bezier_AV)*HI(curr_step)*/
|
||||
" add %8,r0" "\n\t" /* %8:%7 += LO(bezier_AV)*HI(curr_step) << 8*/
|
||||
/* %8:%7 = t*/
|
||||
|
||||
/* uint16_t f = t;*/
|
||||
" mov %5,%7" "\n\t" /* %6:%5 = f*/
|
||||
" mov %6,%8" "\n\t"
|
||||
/* %6:%5 = f*/
|
||||
|
||||
/* umul16x16to16hi(f, f, t); / Range 16 bits (unsigned) [17] */
|
||||
" mul %5,%7" "\n\t" /* r1:r0 = LO(f) * LO(t)*/
|
||||
" mov %9,r1" "\n\t" /* store MIL(LO(f) * LO(t)) in %9, we need it for rounding*/
|
||||
" clr %10" "\n\t" /* %10 = 0*/
|
||||
" clr %11" "\n\t" /* %11 = 0*/
|
||||
" mul %5,%8" "\n\t" /* r1:r0 = LO(f) * HI(t)*/
|
||||
" add %9,r0" "\n\t" /* %9 += LO(LO(f) * HI(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 = HI(LO(f) * HI(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%7" "\n\t" /* r1:r0 = HI(f) * LO(t)*/
|
||||
" add %9,r0" "\n\t" /* %9 += LO(HI(f) * LO(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 += HI(HI(f) * LO(t)) */
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%8" "\n\t" /* r1:r0 = HI(f) * HI(t)*/
|
||||
" add %10,r0" "\n\t" /* %10 += LO(HI(f) * HI(t))*/
|
||||
" adc %11,r1" "\n\t" /* %11 += HI(HI(f) * HI(t))*/
|
||||
" mov %5,%10" "\n\t" /* %6:%5 = */
|
||||
" mov %6,%11" "\n\t" /* f = %10:%11*/
|
||||
|
||||
/* umul16x16to16hi(f, f, t); / Range 16 bits : f = t^3 (unsigned) [17]*/
|
||||
" mul %5,%7" "\n\t" /* r1:r0 = LO(f) * LO(t)*/
|
||||
" mov %1,r1" "\n\t" /* store MIL(LO(f) * LO(t)) in %1, we need it for rounding*/
|
||||
" clr %10" "\n\t" /* %10 = 0*/
|
||||
" clr %11" "\n\t" /* %11 = 0*/
|
||||
" mul %5,%8" "\n\t" /* r1:r0 = LO(f) * HI(t)*/
|
||||
" add %1,r0" "\n\t" /* %1 += LO(LO(f) * HI(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 = HI(LO(f) * HI(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%7" "\n\t" /* r1:r0 = HI(f) * LO(t)*/
|
||||
" add %1,r0" "\n\t" /* %1 += LO(HI(f) * LO(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 += HI(HI(f) * LO(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%8" "\n\t" /* r1:r0 = HI(f) * HI(t)*/
|
||||
" add %10,r0" "\n\t" /* %10 += LO(HI(f) * HI(t))*/
|
||||
" adc %11,r1" "\n\t" /* %11 += HI(HI(f) * HI(t))*/
|
||||
" mov %5,%10" "\n\t" /* %6:%5 =*/
|
||||
" mov %6,%11" "\n\t" /* f = %10:%11*/
|
||||
/* [15 +17*2] = [49]*/
|
||||
|
||||
/* %4:%3:%2 will be acc from now on*/
|
||||
|
||||
/* uint24_t acc = bezier_F; / Range 20 bits (unsigned)*/
|
||||
" clr %9" "\n\t" /* "decimal place we get for free"*/
|
||||
" lds %2,bezier_F" "\n\t"
|
||||
" lds %3,bezier_F+1" "\n\t"
|
||||
" lds %4,bezier_F+2" "\n\t" /* %4:%3:%2 = acc*/
|
||||
|
||||
/* if (A_negative) {*/
|
||||
" lds r0,A_negative" "\n\t"
|
||||
" or r0,%0" "\n\t" /* Is flag signalling negative? */
|
||||
" brne 3f" "\n\t" /* If yes, Skip next instruction if A was negative*/
|
||||
" rjmp 1f" "\n\t" /* Otherwise, jump */
|
||||
|
||||
/* uint24_t v; */
|
||||
/* umul16x24to24hi(v, f, bezier_C); / Range 21bits [29] */
|
||||
/* acc -= v; */
|
||||
"3:" "\n\t"
|
||||
" lds %10, bezier_C" "\n\t" /* %10 = LO(bezier_C)*/
|
||||
" mul %10,%5" "\n\t" /* r1:r0 = LO(bezier_C) * LO(f)*/
|
||||
" sub %9,r1" "\n\t"
|
||||
" sbc %2,%0" "\n\t"
|
||||
" sbc %3,%0" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= HI(LO(bezier_C) * LO(f))*/
|
||||
" lds %11, bezier_C+1" "\n\t" /* %11 = MI(bezier_C)*/
|
||||
" mul %11,%5" "\n\t" /* r1:r0 = MI(bezier_C) * LO(f)*/
|
||||
" sub %9,r0" "\n\t"
|
||||
" sbc %2,r1" "\n\t"
|
||||
" sbc %3,%0" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= MI(bezier_C) * LO(f)*/
|
||||
" lds %1, bezier_C+2" "\n\t" /* %1 = HI(bezier_C)*/
|
||||
" mul %1,%5" "\n\t" /* r1:r0 = MI(bezier_C) * LO(f)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= HI(bezier_C) * LO(f) << 8*/
|
||||
" mul %10,%6" "\n\t" /* r1:r0 = LO(bezier_C) * MI(f)*/
|
||||
" sub %9,r0" "\n\t"
|
||||
" sbc %2,r1" "\n\t"
|
||||
" sbc %3,%0" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= LO(bezier_C) * MI(f)*/
|
||||
" mul %11,%6" "\n\t" /* r1:r0 = MI(bezier_C) * MI(f)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= MI(bezier_C) * MI(f) << 8*/
|
||||
" mul %1,%6" "\n\t" /* r1:r0 = HI(bezier_C) * LO(f)*/
|
||||
" sub %3,r0" "\n\t"
|
||||
" sbc %4,r1" "\n\t" /* %4:%3:%2:%9 -= HI(bezier_C) * LO(f) << 16*/
|
||||
|
||||
/* umul16x16to16hi(f, f, t); / Range 16 bits : f = t^3 (unsigned) [17]*/
|
||||
" mul %5,%7" "\n\t" /* r1:r0 = LO(f) * LO(t)*/
|
||||
" mov %1,r1" "\n\t" /* store MIL(LO(f) * LO(t)) in %1, we need it for rounding*/
|
||||
" clr %10" "\n\t" /* %10 = 0*/
|
||||
" clr %11" "\n\t" /* %11 = 0*/
|
||||
" mul %5,%8" "\n\t" /* r1:r0 = LO(f) * HI(t)*/
|
||||
" add %1,r0" "\n\t" /* %1 += LO(LO(f) * HI(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 = HI(LO(f) * HI(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%7" "\n\t" /* r1:r0 = HI(f) * LO(t)*/
|
||||
" add %1,r0" "\n\t" /* %1 += LO(HI(f) * LO(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 += HI(HI(f) * LO(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%8" "\n\t" /* r1:r0 = HI(f) * HI(t)*/
|
||||
" add %10,r0" "\n\t" /* %10 += LO(HI(f) * HI(t))*/
|
||||
" adc %11,r1" "\n\t" /* %11 += HI(HI(f) * HI(t))*/
|
||||
" mov %5,%10" "\n\t" /* %6:%5 =*/
|
||||
" mov %6,%11" "\n\t" /* f = %10:%11*/
|
||||
|
||||
/* umul16x24to24hi(v, f, bezier_B); / Range 22bits [29]*/
|
||||
/* acc += v; */
|
||||
" lds %10, bezier_B" "\n\t" /* %10 = LO(bezier_B)*/
|
||||
" mul %10,%5" "\n\t" /* r1:r0 = LO(bezier_B) * LO(f)*/
|
||||
" add %9,r1" "\n\t"
|
||||
" adc %2,%0" "\n\t"
|
||||
" adc %3,%0" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += HI(LO(bezier_B) * LO(f))*/
|
||||
" lds %11, bezier_B+1" "\n\t" /* %11 = MI(bezier_B)*/
|
||||
" mul %11,%5" "\n\t" /* r1:r0 = MI(bezier_B) * LO(f)*/
|
||||
" add %9,r0" "\n\t"
|
||||
" adc %2,r1" "\n\t"
|
||||
" adc %3,%0" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += MI(bezier_B) * LO(f)*/
|
||||
" lds %1, bezier_B+2" "\n\t" /* %1 = HI(bezier_B)*/
|
||||
" mul %1,%5" "\n\t" /* r1:r0 = MI(bezier_B) * LO(f)*/
|
||||
" add %2,r0" "\n\t"
|
||||
" adc %3,r1" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += HI(bezier_B) * LO(f) << 8*/
|
||||
" mul %10,%6" "\n\t" /* r1:r0 = LO(bezier_B) * MI(f)*/
|
||||
" add %9,r0" "\n\t"
|
||||
" adc %2,r1" "\n\t"
|
||||
" adc %3,%0" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += LO(bezier_B) * MI(f)*/
|
||||
" mul %11,%6" "\n\t" /* r1:r0 = MI(bezier_B) * MI(f)*/
|
||||
" add %2,r0" "\n\t"
|
||||
" adc %3,r1" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += MI(bezier_B) * MI(f) << 8*/
|
||||
" mul %1,%6" "\n\t" /* r1:r0 = HI(bezier_B) * LO(f)*/
|
||||
" add %3,r0" "\n\t"
|
||||
" adc %4,r1" "\n\t" /* %4:%3:%2:%9 += HI(bezier_B) * LO(f) << 16*/
|
||||
|
||||
/* umul16x16to16hi(f, f, t); / Range 16 bits : f = t^5 (unsigned) [17]*/
|
||||
" mul %5,%7" "\n\t" /* r1:r0 = LO(f) * LO(t)*/
|
||||
" mov %1,r1" "\n\t" /* store MIL(LO(f) * LO(t)) in %1, we need it for rounding*/
|
||||
" clr %10" "\n\t" /* %10 = 0*/
|
||||
" clr %11" "\n\t" /* %11 = 0*/
|
||||
" mul %5,%8" "\n\t" /* r1:r0 = LO(f) * HI(t)*/
|
||||
" add %1,r0" "\n\t" /* %1 += LO(LO(f) * HI(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 = HI(LO(f) * HI(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%7" "\n\t" /* r1:r0 = HI(f) * LO(t)*/
|
||||
" add %1,r0" "\n\t" /* %1 += LO(HI(f) * LO(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 += HI(HI(f) * LO(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%8" "\n\t" /* r1:r0 = HI(f) * HI(t)*/
|
||||
" add %10,r0" "\n\t" /* %10 += LO(HI(f) * HI(t))*/
|
||||
" adc %11,r1" "\n\t" /* %11 += HI(HI(f) * HI(t))*/
|
||||
" mov %5,%10" "\n\t" /* %6:%5 =*/
|
||||
" mov %6,%11" "\n\t" /* f = %10:%11*/
|
||||
|
||||
/* umul16x24to24hi(v, f, bezier_A); / Range 21bits [29]*/
|
||||
/* acc -= v; */
|
||||
" lds %10, bezier_A" "\n\t" /* %10 = LO(bezier_A)*/
|
||||
" mul %10,%5" "\n\t" /* r1:r0 = LO(bezier_A) * LO(f)*/
|
||||
" sub %9,r1" "\n\t"
|
||||
" sbc %2,%0" "\n\t"
|
||||
" sbc %3,%0" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= HI(LO(bezier_A) * LO(f))*/
|
||||
" lds %11, bezier_A+1" "\n\t" /* %11 = MI(bezier_A)*/
|
||||
" mul %11,%5" "\n\t" /* r1:r0 = MI(bezier_A) * LO(f)*/
|
||||
" sub %9,r0" "\n\t"
|
||||
" sbc %2,r1" "\n\t"
|
||||
" sbc %3,%0" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= MI(bezier_A) * LO(f)*/
|
||||
" lds %1, bezier_A+2" "\n\t" /* %1 = HI(bezier_A)*/
|
||||
" mul %1,%5" "\n\t" /* r1:r0 = MI(bezier_A) * LO(f)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= HI(bezier_A) * LO(f) << 8*/
|
||||
" mul %10,%6" "\n\t" /* r1:r0 = LO(bezier_A) * MI(f)*/
|
||||
" sub %9,r0" "\n\t"
|
||||
" sbc %2,r1" "\n\t"
|
||||
" sbc %3,%0" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= LO(bezier_A) * MI(f)*/
|
||||
" mul %11,%6" "\n\t" /* r1:r0 = MI(bezier_A) * MI(f)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= MI(bezier_A) * MI(f) << 8*/
|
||||
" mul %1,%6" "\n\t" /* r1:r0 = HI(bezier_A) * LO(f)*/
|
||||
" sub %3,r0" "\n\t"
|
||||
" sbc %4,r1" "\n\t" /* %4:%3:%2:%9 -= HI(bezier_A) * LO(f) << 16*/
|
||||
" jmp 2f" "\n\t" /* Done!*/
|
||||
|
||||
"1:" "\n\t"
|
||||
|
||||
/* uint24_t v; */
|
||||
/* umul16x24to24hi(v, f, bezier_C); / Range 21bits [29]*/
|
||||
/* acc += v; */
|
||||
" lds %10, bezier_C" "\n\t" /* %10 = LO(bezier_C)*/
|
||||
" mul %10,%5" "\n\t" /* r1:r0 = LO(bezier_C) * LO(f)*/
|
||||
" add %9,r1" "\n\t"
|
||||
" adc %2,%0" "\n\t"
|
||||
" adc %3,%0" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += HI(LO(bezier_C) * LO(f))*/
|
||||
" lds %11, bezier_C+1" "\n\t" /* %11 = MI(bezier_C)*/
|
||||
" mul %11,%5" "\n\t" /* r1:r0 = MI(bezier_C) * LO(f)*/
|
||||
" add %9,r0" "\n\t"
|
||||
" adc %2,r1" "\n\t"
|
||||
" adc %3,%0" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += MI(bezier_C) * LO(f)*/
|
||||
" lds %1, bezier_C+2" "\n\t" /* %1 = HI(bezier_C)*/
|
||||
" mul %1,%5" "\n\t" /* r1:r0 = MI(bezier_C) * LO(f)*/
|
||||
" add %2,r0" "\n\t"
|
||||
" adc %3,r1" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += HI(bezier_C) * LO(f) << 8*/
|
||||
" mul %10,%6" "\n\t" /* r1:r0 = LO(bezier_C) * MI(f)*/
|
||||
" add %9,r0" "\n\t"
|
||||
" adc %2,r1" "\n\t"
|
||||
" adc %3,%0" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += LO(bezier_C) * MI(f)*/
|
||||
" mul %11,%6" "\n\t" /* r1:r0 = MI(bezier_C) * MI(f)*/
|
||||
" add %2,r0" "\n\t"
|
||||
" adc %3,r1" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += MI(bezier_C) * MI(f) << 8*/
|
||||
" mul %1,%6" "\n\t" /* r1:r0 = HI(bezier_C) * LO(f)*/
|
||||
" add %3,r0" "\n\t"
|
||||
" adc %4,r1" "\n\t" /* %4:%3:%2:%9 += HI(bezier_C) * LO(f) << 16*/
|
||||
|
||||
/* umul16x16to16hi(f, f, t); / Range 16 bits : f = t^3 (unsigned) [17]*/
|
||||
" mul %5,%7" "\n\t" /* r1:r0 = LO(f) * LO(t)*/
|
||||
" mov %1,r1" "\n\t" /* store MIL(LO(f) * LO(t)) in %1, we need it for rounding*/
|
||||
" clr %10" "\n\t" /* %10 = 0*/
|
||||
" clr %11" "\n\t" /* %11 = 0*/
|
||||
" mul %5,%8" "\n\t" /* r1:r0 = LO(f) * HI(t)*/
|
||||
" add %1,r0" "\n\t" /* %1 += LO(LO(f) * HI(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 = HI(LO(f) * HI(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%7" "\n\t" /* r1:r0 = HI(f) * LO(t)*/
|
||||
" add %1,r0" "\n\t" /* %1 += LO(HI(f) * LO(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 += HI(HI(f) * LO(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%8" "\n\t" /* r1:r0 = HI(f) * HI(t)*/
|
||||
" add %10,r0" "\n\t" /* %10 += LO(HI(f) * HI(t))*/
|
||||
" adc %11,r1" "\n\t" /* %11 += HI(HI(f) * HI(t))*/
|
||||
" mov %5,%10" "\n\t" /* %6:%5 =*/
|
||||
" mov %6,%11" "\n\t" /* f = %10:%11*/
|
||||
|
||||
/* umul16x24to24hi(v, f, bezier_B); / Range 22bits [29]*/
|
||||
/* acc -= v;*/
|
||||
" lds %10, bezier_B" "\n\t" /* %10 = LO(bezier_B)*/
|
||||
" mul %10,%5" "\n\t" /* r1:r0 = LO(bezier_B) * LO(f)*/
|
||||
" sub %9,r1" "\n\t"
|
||||
" sbc %2,%0" "\n\t"
|
||||
" sbc %3,%0" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= HI(LO(bezier_B) * LO(f))*/
|
||||
" lds %11, bezier_B+1" "\n\t" /* %11 = MI(bezier_B)*/
|
||||
" mul %11,%5" "\n\t" /* r1:r0 = MI(bezier_B) * LO(f)*/
|
||||
" sub %9,r0" "\n\t"
|
||||
" sbc %2,r1" "\n\t"
|
||||
" sbc %3,%0" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= MI(bezier_B) * LO(f)*/
|
||||
" lds %1, bezier_B+2" "\n\t" /* %1 = HI(bezier_B)*/
|
||||
" mul %1,%5" "\n\t" /* r1:r0 = MI(bezier_B) * LO(f)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= HI(bezier_B) * LO(f) << 8*/
|
||||
" mul %10,%6" "\n\t" /* r1:r0 = LO(bezier_B) * MI(f)*/
|
||||
" sub %9,r0" "\n\t"
|
||||
" sbc %2,r1" "\n\t"
|
||||
" sbc %3,%0" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= LO(bezier_B) * MI(f)*/
|
||||
" mul %11,%6" "\n\t" /* r1:r0 = MI(bezier_B) * MI(f)*/
|
||||
" sub %2,r0" "\n\t"
|
||||
" sbc %3,r1" "\n\t"
|
||||
" sbc %4,%0" "\n\t" /* %4:%3:%2:%9 -= MI(bezier_B) * MI(f) << 8*/
|
||||
" mul %1,%6" "\n\t" /* r1:r0 = HI(bezier_B) * LO(f)*/
|
||||
" sub %3,r0" "\n\t"
|
||||
" sbc %4,r1" "\n\t" /* %4:%3:%2:%9 -= HI(bezier_B) * LO(f) << 16*/
|
||||
|
||||
/* umul16x16to16hi(f, f, t); / Range 16 bits : f = t^5 (unsigned) [17]*/
|
||||
" mul %5,%7" "\n\t" /* r1:r0 = LO(f) * LO(t)*/
|
||||
" mov %1,r1" "\n\t" /* store MIL(LO(f) * LO(t)) in %1, we need it for rounding*/
|
||||
" clr %10" "\n\t" /* %10 = 0*/
|
||||
" clr %11" "\n\t" /* %11 = 0*/
|
||||
" mul %5,%8" "\n\t" /* r1:r0 = LO(f) * HI(t)*/
|
||||
" add %1,r0" "\n\t" /* %1 += LO(LO(f) * HI(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 = HI(LO(f) * HI(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%7" "\n\t" /* r1:r0 = HI(f) * LO(t)*/
|
||||
" add %1,r0" "\n\t" /* %1 += LO(HI(f) * LO(t))*/
|
||||
" adc %10,r1" "\n\t" /* %10 += HI(HI(f) * LO(t))*/
|
||||
" adc %11,%0" "\n\t" /* %11 += carry*/
|
||||
" mul %6,%8" "\n\t" /* r1:r0 = HI(f) * HI(t)*/
|
||||
" add %10,r0" "\n\t" /* %10 += LO(HI(f) * HI(t))*/
|
||||
" adc %11,r1" "\n\t" /* %11 += HI(HI(f) * HI(t))*/
|
||||
" mov %5,%10" "\n\t" /* %6:%5 =*/
|
||||
" mov %6,%11" "\n\t" /* f = %10:%11*/
|
||||
|
||||
/* umul16x24to24hi(v, f, bezier_A); / Range 21bits [29]*/
|
||||
/* acc += v; */
|
||||
" lds %10, bezier_A" "\n\t" /* %10 = LO(bezier_A)*/
|
||||
" mul %10,%5" "\n\t" /* r1:r0 = LO(bezier_A) * LO(f)*/
|
||||
" add %9,r1" "\n\t"
|
||||
" adc %2,%0" "\n\t"
|
||||
" adc %3,%0" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += HI(LO(bezier_A) * LO(f))*/
|
||||
" lds %11, bezier_A+1" "\n\t" /* %11 = MI(bezier_A)*/
|
||||
" mul %11,%5" "\n\t" /* r1:r0 = MI(bezier_A) * LO(f)*/
|
||||
" add %9,r0" "\n\t"
|
||||
" adc %2,r1" "\n\t"
|
||||
" adc %3,%0" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += MI(bezier_A) * LO(f)*/
|
||||
" lds %1, bezier_A+2" "\n\t" /* %1 = HI(bezier_A)*/
|
||||
" mul %1,%5" "\n\t" /* r1:r0 = MI(bezier_A) * LO(f)*/
|
||||
" add %2,r0" "\n\t"
|
||||
" adc %3,r1" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += HI(bezier_A) * LO(f) << 8*/
|
||||
" mul %10,%6" "\n\t" /* r1:r0 = LO(bezier_A) * MI(f)*/
|
||||
" add %9,r0" "\n\t"
|
||||
" adc %2,r1" "\n\t"
|
||||
" adc %3,%0" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += LO(bezier_A) * MI(f)*/
|
||||
" mul %11,%6" "\n\t" /* r1:r0 = MI(bezier_A) * MI(f)*/
|
||||
" add %2,r0" "\n\t"
|
||||
" adc %3,r1" "\n\t"
|
||||
" adc %4,%0" "\n\t" /* %4:%3:%2:%9 += MI(bezier_A) * MI(f) << 8*/
|
||||
" mul %1,%6" "\n\t" /* r1:r0 = HI(bezier_A) * LO(f)*/
|
||||
" add %3,r0" "\n\t"
|
||||
" adc %4,r1" "\n\t" /* %4:%3:%2:%9 += HI(bezier_A) * LO(f) << 16*/
|
||||
"2:" "\n\t"
|
||||
" clr __zero_reg__" /* C runtime expects r1 = __zero_reg__ = 0 */
|
||||
: "+r"(r0),
|
||||
"+r"(r1),
|
||||
"+r"(r2),
|
||||
"+r"(r3),
|
||||
"+r"(r4),
|
||||
"+r"(r5),
|
||||
"+r"(r6),
|
||||
"+r"(r7),
|
||||
"+r"(r8),
|
||||
"+r"(r9),
|
||||
"+r"(r10),
|
||||
"+r"(r11)
|
||||
:
|
||||
:"cc","r0","r1"
|
||||
);
|
||||
return (r2 | (uint16_t(r3) << 8)) | (uint32_t(r4) << 16);
|
||||
}
|
||||
|
||||
#else
|
||||
|
||||
// For all the other 32bit CPUs
|
||||
FORCE_INLINE void Stepper::_calc_bezier_curve_coeffs(const int32_t v0, const int32_t v1, const uint32_t av) {
|
||||
// Calculate the Bézier coefficients
|
||||
bezier_A = 768 * (v1 - v0);
|
||||
bezier_B = 1920 * (v0 - v1);
|
||||
bezier_C = 1280 * (v1 - v0);
|
||||
bezier_F = 128 * v0;
|
||||
bezier_AV = av;
|
||||
}
|
||||
|
||||
FORCE_INLINE int32_t Stepper::_eval_bezier_curve(const uint32_t curr_step) {
|
||||
#if defined(__ARM__) || defined(__thumb__)
|
||||
|
||||
// For ARM Cortex M3/M4 CPUs, we have the optimized assembler version, that takes 43 cycles to execute
|
||||
register uint32_t flo = 0;
|
||||
register uint32_t fhi = bezier_AV * curr_step;
|
||||
register uint32_t t = fhi;
|
||||
register int32_t alo = bezier_F;
|
||||
register int32_t ahi = 0;
|
||||
register int32_t A = bezier_A;
|
||||
register int32_t B = bezier_B;
|
||||
register int32_t C = bezier_C;
|
||||
|
||||
__asm__ __volatile__(
|
||||
".syntax unified" "\n\t" // is to prevent CM0,CM1 non-unified syntax
|
||||
" lsrs %[ahi],%[alo],#1" "\n\t" // a = F << 31 1 cycles
|
||||
" lsls %[alo],%[alo],#31" "\n\t" // 1 cycles
|
||||
" umull %[flo],%[fhi],%[fhi],%[t]" "\n\t" // f *= t 5 cycles [fhi:flo=64bits]
|
||||
" umull %[flo],%[fhi],%[fhi],%[t]" "\n\t" // f>>=32; f*=t 5 cycles [fhi:flo=64bits]
|
||||
" lsrs %[flo],%[fhi],#1" "\n\t" // 1 cycles [31bits]
|
||||
" smlal %[alo],%[ahi],%[flo],%[C]" "\n\t" // a+=(f>>33)*C; 5 cycles
|
||||
" umull %[flo],%[fhi],%[fhi],%[t]" "\n\t" // f>>=32; f*=t 5 cycles [fhi:flo=64bits]
|
||||
" lsrs %[flo],%[fhi],#1" "\n\t" // 1 cycles [31bits]
|
||||
" smlal %[alo],%[ahi],%[flo],%[B]" "\n\t" // a+=(f>>33)*B; 5 cycles
|
||||
" umull %[flo],%[fhi],%[fhi],%[t]" "\n\t" // f>>=32; f*=t 5 cycles [fhi:flo=64bits]
|
||||
" lsrs %[flo],%[fhi],#1" "\n\t" // f>>=33; 1 cycles [31bits]
|
||||
" smlal %[alo],%[ahi],%[flo],%[A]" "\n\t" // a+=(f>>33)*A; 5 cycles
|
||||
" lsrs %[alo],%[ahi],#6" "\n\t" // a>>=38 1 cycles
|
||||
: [alo]"+r"( alo ) ,
|
||||
[flo]"+r"( flo ) ,
|
||||
[fhi]"+r"( fhi ) ,
|
||||
[ahi]"+r"( ahi ) ,
|
||||
[A]"+r"( A ) , // <== Note: Even if A, B, C, and t registers are INPUT ONLY
|
||||
[B]"+r"( B ) , // GCC does bad optimizations on the code if we list them as
|
||||
[C]"+r"( C ) , // such, breaking this function. So, to avoid that problem,
|
||||
[t]"+r"( t ) // we list all registers as input-outputs.
|
||||
:
|
||||
: "cc"
|
||||
);
|
||||
return alo;
|
||||
|
||||
#else
|
||||
|
||||
// For non ARM targets, we provide a fallback implementation. Really doubt it
|
||||
// will be useful, unless the processor is fast and 32bit
|
||||
|
||||
uint32_t t = bezier_AV * curr_step; // t: Range 0 - 1^32 = 32 bits
|
||||
uint64_t f = t;
|
||||
f *= t; // Range 32*2 = 64 bits (unsigned)
|
||||
f >>= 32; // Range 32 bits (unsigned)
|
||||
f *= t; // Range 32*2 = 64 bits (unsigned)
|
||||
f >>= 32; // Range 32 bits : f = t^3 (unsigned)
|
||||
int64_t acc = (int64_t) bezier_F << 31; // Range 63 bits (signed)
|
||||
acc += ((uint32_t) f >> 1) * (int64_t) bezier_C; // Range 29bits + 31 = 60bits (plus sign)
|
||||
f *= t; // Range 32*2 = 64 bits
|
||||
f >>= 32; // Range 32 bits : f = t^3 (unsigned)
|
||||
acc += ((uint32_t) f >> 1) * (int64_t) bezier_B; // Range 29bits + 31 = 60bits (plus sign)
|
||||
f *= t; // Range 32*2 = 64 bits
|
||||
f >>= 32; // Range 32 bits : f = t^3 (unsigned)
|
||||
acc += ((uint32_t) f >> 1) * (int64_t) bezier_A; // Range 28bits + 31 = 59bits (plus sign)
|
||||
acc >>= (31 + 7); // Range 24bits (plus sign)
|
||||
return (int32_t) acc;
|
||||
|
||||
#endif
|
||||
}
|
||||
#endif
|
||||
#endif // BEZIER_JERK_CONTROL
|
||||
|
||||
/**
|
||||
|
|
@ -660,7 +1268,7 @@ void Stepper::isr() {
|
|||
|
||||
#if ENABLED(BEZIER_JERK_CONTROL)
|
||||
// Initialize the Bézier speed curve
|
||||
_calc_bezier_curve_coeffs(current_block->initial_rate, current_block->cruise_rate, current_block->acceleration_time);
|
||||
_calc_bezier_curve_coeffs(current_block->initial_rate, current_block->cruise_rate, current_block->acceleration_time_inverse);
|
||||
|
||||
// We have not started the 2nd half of the trapezoid
|
||||
bezier_2nd_half = false;
|
||||
|
|
@ -953,7 +1561,7 @@ void Stepper::isr() {
|
|||
if (!bezier_2nd_half) {
|
||||
|
||||
// Initialize the Bézier speed curve
|
||||
_calc_bezier_curve_coeffs(current_block->cruise_rate, current_block->final_rate, current_block->deceleration_time);
|
||||
_calc_bezier_curve_coeffs(current_block->cruise_rate, current_block->final_rate, current_block->deceleration_time_inverse);
|
||||
bezier_2nd_half = true;
|
||||
}
|
||||
|
||||
|
|
|
|||
|
|
@ -98,12 +98,15 @@ class Stepper {
|
|||
static volatile uint32_t step_events_completed; // The number of step events executed in the current block
|
||||
|
||||
#if ENABLED(BEZIER_JERK_CONTROL)
|
||||
static int32_t bezier_A, // A coefficient in Bézier speed curve
|
||||
bezier_B, // B coefficient in Bézier speed curve
|
||||
bezier_C, // C coefficient in Bézier speed curve
|
||||
bezier_F; // F coefficient in Bézier speed curve
|
||||
static uint32_t bezier_AV; // AV coefficient in Bézier speed curve
|
||||
static bool bezier_2nd_half; // If Bézier curve has been initialized or not
|
||||
static int32_t bezier_A, // A coefficient in Bézier speed curve
|
||||
bezier_B, // B coefficient in Bézier speed curve
|
||||
bezier_C; // C coefficient in Bézier speed curve
|
||||
static uint32_t bezier_F; // F coefficient in Bézier speed curve
|
||||
static uint32_t bezier_AV; // AV coefficient in Bézier speed curve
|
||||
#ifdef __AVR__
|
||||
static bool A_negative; // If A coefficient was negative
|
||||
#endif
|
||||
static bool bezier_2nd_half; // If Bézier curve has been initialized or not
|
||||
#endif
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
|
|
@ -361,7 +364,7 @@ class Stepper {
|
|||
}
|
||||
|
||||
#if ENABLED(BEZIER_JERK_CONTROL)
|
||||
static void _calc_bezier_curve_coeffs(const int32_t v0, const int32_t v1, const uint32_t steps);
|
||||
static void _calc_bezier_curve_coeffs(const int32_t v0, const int32_t v1, const uint32_t av);
|
||||
static int32_t _eval_bezier_curve(const uint32_t curr_step);
|
||||
#endif
|
||||
|
||||
|
|
|
|||
Loading…
Reference in a new issue