From 57cee04c899084454791aed925da6bea648d203f Mon Sep 17 00:00:00 2001 From: John Lagonikas <39417467+zeleps@users.noreply.github.com> Date: Sat, 5 Feb 2022 03:10:59 +0200 Subject: [PATCH] =?UTF-8?q?=F0=9F=90=9B=20Fix=20dual=20MAX31865=20initiali?= =?UTF-8?q?zation=20issues=20(#23496)?= MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit --- Marlin/Configuration_adv.h | 29 ++-- Marlin/src/HAL/shared/Delay.h | 2 + Marlin/src/libs/MAX31865.cpp | 315 ++++++++++++++++++++-------------- Marlin/src/libs/MAX31865.h | 22 ++- 4 files changed, 216 insertions(+), 152 deletions(-) diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 35e8044355..cf30684e89 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -138,24 +138,21 @@ #endif /** - * Configuration options for MAX Thermocouples (-2, -3, -5). - * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus. - * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2 - * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz. - * MAX31865_USE_READ_ERROR_DETECTION: Detects random read errors from value spikes (a 20°C difference in less than 1sec) - * MAX31865_USE_AUTO_MODE: Faster and more frequent reads than 1-shot, but bias voltage always on, slightly affecting RTD temperature. - * MAX31865_MIN_SAMPLING_TIME_MSEC: in 1-shot mode, the minimum time between subsequent reads. This reduces the effect of bias voltage by leaving the sensor unpowered for longer intervals. - * MAX31865_WIRE_OHMS: In 2-wire configurations, manually set the wire resistance for more accurate readings + * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ -//#define TEMP_SENSOR_FORCE_HW_SPI -//#define MAX31865_SENSOR_WIRES_0 2 +//#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. +//#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 -//#define MAX31865_50HZ_FILTER -//#define MAX31865_USE_READ_ERROR_DETECTION -//#define MAX31865_USE_AUTO_MODE -//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 -//#define MAX31865_WIRE_OHMS_0 0.0f -//#define MAX31865_WIRE_OHMS_1 0.0f + +//#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. +//#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. + +//#define MAX31865_USE_AUTO_MODE // Read faster and more often than 1-shot; bias voltage always on; slight effect on RTD temperature. +//#define MAX31865_MIN_SAMPLING_TIME_MSEC 100 // (ms) 1-shot: minimum read interval. Reduces bias voltage effects by leaving sensor unpowered for longer intervals. +//#define MAX31865_IGNORE_INITIAL_FAULTY_READS 10 // Ignore some read faults (keeping the temperature reading) to work around a possible issue (#23439). + +//#define MAX31865_WIRE_OHMS_0 0.95f // For 2-wire, set the wire resistances for more accurate readings. +//#define MAX31865_WIRE_OHMS_1 0.0f /** * Hephestos 2 24V heated bed upgrade kit. diff --git a/Marlin/src/HAL/shared/Delay.h b/Marlin/src/HAL/shared/Delay.h index df07881f01..a6795a78ea 100644 --- a/Marlin/src/HAL/shared/Delay.h +++ b/Marlin/src/HAL/shared/Delay.h @@ -166,6 +166,8 @@ void calibrate_delay_loop(); // Delay in microseconds #define DELAY_US(x) DELAY_CYCLES((x) * ((F_CPU) / 1000000UL)) + #define DELAY_CYCLES_VAR DELAY_CYCLES + #elif defined(ESP32) || defined(__PLAT_LINUX__) || defined(__PLAT_NATIVE_SIM__) // DELAY_CYCLES specified inside platform diff --git a/Marlin/src/libs/MAX31865.cpp b/Marlin/src/libs/MAX31865.cpp index 1cafbe5f17..c042504cf8 100644 --- a/Marlin/src/libs/MAX31865.cpp +++ b/Marlin/src/libs/MAX31865.cpp @@ -50,10 +50,6 @@ #define MAX31865_MIN_SAMPLING_TIME_MSEC 0 #endif -#ifdef TARGET_LPC1768 - #include -#endif - #define DEBUG_OUT ENABLED(DEBUG_MAX31865) #include "../core/debug_out.h" @@ -151,24 +147,62 @@ void MAX31865::begin(max31865_numwires_t wires, float zero_res, float ref_res, f digitalWrite(cselPin, HIGH); if (sclkPin != TERN(LARGE_PINMAP, -1UL, 255)) - softSpiBegin(SPI_QUARTER_SPEED); // Define pin modes for Software SPI + softSpiInit(); // Define pin modes for Software SPI else { - DEBUG_ECHOLNPGM("Initializing MAX31865 Hardware SPI"); + DEBUG_ECHOLNPGM("Init MAX31865 Hardware SPI"); SPI.begin(); // Start and configure hardware SPI } initFixedFlags(wires); - clearFault(); // also initializes flags + DEBUG_ECHOLNPGM("MAX31865 Regs: CFG ", readRegister8(MAX31865_CONFIG_REG), + "|RTD ", readRegister16(MAX31865_RTDMSB_REG), + "|HTHRS ", readRegister16(MAX31865_HFAULTMSB_REG), + "|LTHRS ", readRegister16(MAX31865_LFAULTMSB_REG), + "|FLT ", readRegister8(MAX31865_FAULTSTAT_REG)); - #if DISABLED(MAX31865_USE_AUTO_MODE) // make a proper first 1 shot read to initialize _lastRead + // fault detection cycle seems to initialize the sensor better + runAutoFaultDetectionCycle(); // also initializes flags + + if (lastFault) + SERIAL_ECHOLNPGM("MAX31865 init fault ", lastFault); + + writeRegister16(MAX31865_HFAULTMSB_REG, 0xFFFF); + writeRegister16(MAX31865_LFAULTMSB_REG, 0); + + #if ENABLED(MAX31865_USE_AUTO_MODE) // make a proper first read to initialize _lastRead + + uint16_t rtd = readRegister16(MAX31865_RTDMSB_REG); + + #if MAX31865_IGNORE_INITIAL_FAULTY_READS > 0 + rtd = fixFault(rtd); + #endif + + if (rtd & 1) { + lastRead = 0xFFFF; // some invalid value + lastFault = readRegister8(MAX31865_FAULTSTAT_REG); + clearFault(); // also clears the bias voltage flag, so no further action is required + + DEBUG_ECHOLNPGM("MAX31865 read fault: ", rtd); + } + else { + DEBUG_ECHOLNPGM("RTD MSB:", (rtd >> 8), " RTD LSB:", (rtd & 0x00FF)); + lastRead = rtd; + TERN_(MAX31865_USE_READ_ERROR_DETECTION, lastReadStamp = millis()); + } + + #else enableBias(); - DELAY_US(11500); + DELAY_US(2000); // according to the datasheet, 10.5τ+1msec (see below) oneShot(); - DELAY_US(65000); + DELAY_US(63000); uint16_t rtd = readRegister16(MAX31865_RTDMSB_REG); + #if MAX31865_IGNORE_INITIAL_FAULTY_READS > 0 + rtd = fixFault(rtd); + #endif + if (rtd & 1) { lastRead = 0xFFFF; // some invalid value lastFault = readRegister8(MAX31865_FAULTSTAT_REG); @@ -189,7 +223,7 @@ void MAX31865::begin(max31865_numwires_t wires, float zero_res, float ref_res, f TERN_(MAX31865_USE_READ_ERROR_DETECTION, lastReadStamp = now); } - #endif // !MAX31865_USE_AUTO_MODE + #endif // MAX31865_USE_AUTO_MODE DEBUG_ECHOLNPGM( TERN(LARGE_PINMAP, "LARGE_PINMAP", "Regular") @@ -198,7 +232,7 @@ void MAX31865::begin(max31865_numwires_t wires, float zero_res, float ref_res, f " sclkPin: ", sclkPin, " mosiPin: ", mosiPin, " config: ", readRegister8(MAX31865_CONFIG_REG) - ); + ); } /** @@ -240,6 +274,29 @@ void MAX31865::oneShot() { setConfig(MAX31865_CONFIG_1SHOT | MAX31865_CONFIG_BIAS, 1); } +void MAX31865::runAutoFaultDetectionCycle() { + writeRegister8(MAX31865_CONFIG_REG, (stdFlags & 0x11) | 0x84 ); // cfg reg = 100X010Xb + DELAY_US(600); + for (int i = 0; i < 10 && (readRegister8(MAX31865_CONFIG_REG) & 0xC) > 0; i++) DELAY_US(100); // Fault det completes when bits 2 and 3 are zero (or after 10 tries) + readFault(); + clearFault(); +} + +/** + * Set a value in the configuration register. + * + * @param config 8-bit value for the config item + * @param enable whether to enable or disable the value + */ +void MAX31865::setConfig(uint8_t config, bool enable) { + uint8_t t = stdFlags; + if (enable) + t |= config; + else + t &= ~config; + writeRegister8(MAX31865_CONFIG_REG, t); +} + /** * Initialize standard flags with flags that will not change during operation (Hz, polling mode and no. of wires) * @@ -249,12 +306,59 @@ void MAX31865::initFixedFlags(max31865_numwires_t wires) { // set config-defined flags (same for all sensors) stdFlags = TERN(MAX31865_50HZ_FILTER, MAX31865_CONFIG_FILT50HZ, MAX31865_CONFIG_FILT60HZ) | - TERN(MAX31865_USE_AUTO_MODE, MAX31865_CONFIG_MODEAUTO | MAX31865_CONFIG_BIAS, MAX31865_CONFIG_MODEOFF); + TERN(MAX31865_USE_AUTO_MODE, MAX31865_CONFIG_MODEAUTO | MAX31865_CONFIG_BIAS, MAX31865_CONFIG_MODEOFF); if (wires == MAX31865_3WIRE) - stdFlags |= MAX31865_CONFIG_3WIRE; - else // 2 or 4 wire - stdFlags &= ~MAX31865_CONFIG_3WIRE; + stdFlags |= MAX31865_CONFIG_3WIRE; // 3 wire + else + stdFlags &= ~MAX31865_CONFIG_3WIRE; // 2 or 4 wire +} + +#if MAX31865_IGNORE_INITIAL_FAULTY_READS > 0 + + inline uint16_t MAX31865::fixFault(uint16_t rtd) { + if (!ignore_faults || !(rtd & 1)) + return rtd; + + ignore_faults--; + clearFault(); + + DEBUG_ECHOLNPGM("MAX31865 ignoring fault ", (MAX31865_IGNORE_INITIAL_FAULTY_READS) - ignore_faults); + + return rtd & ~1; // 0xFFFE + } + +#endif + +inline uint16_t MAX31865::readRawImmediate() { + uint16_t rtd = readRegister16(MAX31865_RTDMSB_REG); + DEBUG_ECHOLNPGM("MAX31865 RTD MSB:", (rtd >> 8), " LSB:", (rtd & 0x00FF)); + + #if MAX31865_IGNORE_INITIAL_FAULTY_READS > 0 + rtd = fixFault(rtd); + #endif + + if (rtd & 1) { + lastFault = readRegister8(MAX31865_FAULTSTAT_REG); + lastRead |= 1; + clearFault(); // also clears the bias voltage flag, so no further action is required + DEBUG_ECHOLNPGM("MAX31865 read fault: ", lastFault); + } + else { + TERN_(MAX31865_USE_READ_ERROR_DETECTION, const millis_t ms = millis()); + if (TERN0(MAX31865_USE_READ_ERROR_DETECTION, ABS((int)(lastRead - rtd)) > 500 && PENDING(ms, lastReadStamp + 1000))) { + // If 2 readings within 1s differ too much (~20°C) it's a read error. + lastFault = 0x01; + lastRead |= 1; + DEBUG_ECHOLNPGM("MAX31865 read error: ", rtd); + } + else { + lastRead = rtd; + TERN_(MAX31865_USE_READ_ERROR_DETECTION, lastReadStamp = ms); + } + } + + return rtd; } /** @@ -267,30 +371,13 @@ uint16_t MAX31865::readRaw() { #if ENABLED(MAX31865_USE_AUTO_MODE) - const uint16_t rtd = readRegister16(MAX31865_RTDMSB_REG); - DEBUG_ECHOLNPGM("MAX31865 RTD MSB:", (rtd >> 8), " LSB:", (rtd & 0x00FF)); - - if (rtd & 1) { - lastFault = readRegister8(MAX31865_FAULTSTAT_REG); - lastRead |= 1; - clearFault(); // also clears the bias voltage flag, so no further action is required - DEBUG_ECHOLNPGM("MAX31865 read fault: ", rtd); - } - #if ENABLED(MAX31865_USE_READ_ERROR_DETECTION) - else if (ABS(lastRead - rtd) > 500 && PENDING(millis(), lastReadStamp + 1000)) { // if two readings within a second differ too much (~20°C), consider it a read error. - lastFault = 0x01; - lastRead |= 1; - DEBUG_ECHOLNPGM("MAX31865 read error: ", rtd); - } - #endif - else { - lastRead = rtd; - TERN_(MAX31865_USE_READ_ERROR_DETECTION, lastReadStamp = millis()); - } + readRawImmediate(); #else - if (PENDING(millis(), nextEventStamp)) { + const millis_t ms = millis(); + + if (PENDING(ms, nextEventStamp)) { DEBUG_ECHOLNPGM("MAX31865 waiting for event ", nextEvent); return lastRead; } @@ -298,46 +385,26 @@ uint16_t MAX31865::readRaw() { switch (nextEvent) { case SETUP_BIAS_VOLTAGE: enableBias(); - nextEventStamp = millis() + 11; // wait at least 11msec before enabling 1shot + nextEventStamp = ms + 2; // wait at least 10.5*τ (τ = 100nF*430Ω max for PT100 / 10nF*4.3ΚΩ for PT1000 = 43μsec) + 1msec nextEvent = SETUP_1_SHOT_MODE; DEBUG_ECHOLNPGM("MAX31865 bias voltage enabled"); break; case SETUP_1_SHOT_MODE: oneShot(); - nextEventStamp = millis() + 65; // wait at least 65msec before reading RTD register + nextEventStamp = ms + TERN(MAX31865_50HZ_FILTER, 63, 52); // wait at least 52msec for 60Hz (63msec for 50Hz) before reading RTD register nextEvent = READ_RTD_REG; DEBUG_ECHOLNPGM("MAX31865 1 shot mode enabled"); break; - case READ_RTD_REG: { - const uint16_t rtd = readRegister16(MAX31865_RTDMSB_REG); - DEBUG_ECHOLNPGM("MAX31865 RTD MSB:", (rtd >> 8), " LSB:", (rtd & 0x00FF)); + case READ_RTD_REG: - if (rtd & 1) { - lastFault = readRegister8(MAX31865_FAULTSTAT_REG); - lastRead |= 1; - clearFault(); // also clears the bias voltage flag, so no further action is required - DEBUG_ECHOLNPGM("MAX31865 read fault: ", rtd); - } - #if ENABLED(MAX31865_USE_READ_ERROR_DETECTION) - else if (ABS(lastRead - rtd) > 500 && PENDING(millis(), lastReadStamp + 1000)) { // if two readings within a second differ too much (~20°C), consider it a read error. - lastFault = 0x01; - lastRead |= 1; - DEBUG_ECHOLNPGM("MAX31865 read error: ", rtd); - } - #endif - else { - lastRead = rtd; - TERN_(MAX31865_USE_READ_ERROR_DETECTION, lastReadStamp = millis()); - } - - if (!(rtd & 1)) // if clearFault() was not invoked, need to clear the bias voltage and 1-shot flags + if (!(readRawImmediate() & 1)) // if clearFault() was not invoked, need to clear the bias voltage and 1-shot flags resetFlags(); nextEvent = SETUP_BIAS_VOLTAGE; - nextEventStamp = millis() + MAX31865_MIN_SAMPLING_TIME_MSEC; // next step should not occur within less than MAX31865_MIN_SAMPLING_TIME_MSEC from the last one - } break; + nextEventStamp = ms + (MAX31865_MIN_SAMPLING_TIME_MSEC); // next step should not occur within less than MAX31865_MIN_SAMPLING_TIME_MSEC from the last one + break; } #endif @@ -411,21 +478,17 @@ float MAX31865::temperature(float rtd_res) { return temp; } -// -// private: -// - /** - * Set a value in the configuration register. - * - * @param config 8-bit value for the config item - * @param enable whether to enable or disable the value + * MAX31865 SPI Timing constants + * See MAX31865 datasheet (https://datasheets.maximintegrated.com/en/ds/MAX31865.pdf) + * All timings in nsec, minimum values. */ -void MAX31865::setConfig(uint8_t config, bool enable) { - uint8_t t = stdFlags; - if (enable) t |= config; else t &= ~config; - writeRegister8(MAX31865_CONFIG_REG, t); -} + +#define MAX31865_SPI_TIMING_TCC 400 // CS to SCLK setup +#define MAX31865_SPI_TIMING_TDC 35 // Data to SCLK setup +#define MAX31865_SPI_TIMING_TCL 100 // SCK half period +#define MAX31865_SPI_TIMING_TCCH 100 // SCK to CS hold +#define MAX31865_SPI_TIMING_TCWH 400 // CS inactive time (min) /** * Read a single byte from the specified register address. @@ -459,18 +522,10 @@ uint16_t MAX31865::readRegister16(uint8_t addr) { * @param n the number of bytes to read */ void MAX31865::readRegisterN(uint8_t addr, uint8_t buffer[], uint8_t n) { + addr &= 0x7F; // make sure top bit is not set - if (sclkPin == TERN(LARGE_PINMAP, -1UL, 255)) - SPI.beginTransaction(spiConfig); - else - digitalWrite(sclkPin, LOW); - - digitalWrite(cselPin, LOW); - - #ifdef TARGET_LPC1768 - DELAY_CYCLES(spiSpeed); - #endif + spiBeginTransaction(); spiTransfer(addr); while (n--) { @@ -478,10 +533,15 @@ void MAX31865::readRegisterN(uint8_t addr, uint8_t buffer[], uint8_t n) { buffer++; } - if (sclkPin == TERN(LARGE_PINMAP, -1UL, 255)) - SPI.endTransaction(); + spiEndTransaction(); +} - digitalWrite(cselPin, HIGH); +void MAX31865::writeRegister16(uint8_t addr, uint16_t data) { + spiBeginTransaction(); + spiTransfer(addr | 0x80); // make sure top bit is set + spiTransfer(data >> 8); + spiTransfer(data & 0xFF); + spiEndTransaction(); } /** @@ -491,22 +551,31 @@ void MAX31865::readRegisterN(uint8_t addr, uint8_t buffer[], uint8_t n) { * @param data the data to write */ void MAX31865::writeRegister8(uint8_t addr, uint8_t data) { + spiBeginTransaction(); + spiTransfer(addr | 0x80); // make sure top bit is set + spiTransfer(data); + spiEndTransaction(); +} + +void MAX31865::spiBeginTransaction() { + digitalWrite(sclkPin, LOW); // ensure CPOL0 + DELAY_NS_VAR(MAX31865_SPI_TIMING_TCWH); // ensure minimum time of CS inactivity after previous operation + digitalWrite(cselPin, LOW); + DELAY_NS_VAR(MAX31865_SPI_TIMING_TCC); + if (sclkPin == TERN(LARGE_PINMAP, -1UL, 255)) SPI.beginTransaction(spiConfig); else - digitalWrite(sclkPin, LOW); - - digitalWrite(cselPin, LOW); - - #ifdef TARGET_LPC1768 - DELAY_CYCLES(spiSpeed); - #endif - - spiTransfer(addr | 0x80); // make sure top bit is set - spiTransfer(data); + digitalWrite(sclkPin, HIGH); +} +void MAX31865::spiEndTransaction() { if (sclkPin == TERN(LARGE_PINMAP, -1UL, 255)) SPI.endTransaction(); + else + digitalWrite(sclkPin, LOW); + + DELAY_NS_VAR(MAX31865_SPI_TIMING_TCCH); digitalWrite(cselPin, HIGH); } @@ -521,42 +590,30 @@ void MAX31865::writeRegister8(uint8_t addr, uint8_t data) { * @return the 8-bit response */ uint8_t MAX31865::spiTransfer(uint8_t x) { - if (sclkPin == TERN(LARGE_PINMAP, -1UL, 255)) return SPI.transfer(x); - #ifdef TARGET_LPC1768 - - return swSpiTransfer(x, spiSpeed, sclkPin, misoPin, mosiPin); - - #else - - uint8_t reply = 0; - for (int i = 7; i >= 0; i--) { - digitalWrite(sclkPin, HIGH); DELAY_NS_VAR(spiDelay); - reply <<= 1; - digitalWrite(mosiPin, x & _BV(i)); DELAY_NS_VAR(spiDelay); - if (digitalRead(misoPin)) reply |= 1; - digitalWrite(sclkPin, LOW); DELAY_NS_VAR(spiDelay); - } - return reply; - - #endif + uint8_t reply = 0; + for (int i = 7; i >= 0; i--) { + digitalWrite(mosiPin, x & _BV(i)); + DELAY_NS_VAR(MAX31865_SPI_TIMING_TDC); + digitalWrite(sclkPin, LOW); + DELAY_NS_VAR(MAX31865_SPI_TIMING_TCL - MAX31865_SPI_TIMING_TDC); + reply <<= 1; + if (digitalRead(misoPin)) reply |= 1; + DELAY_NS_VAR(MAX31865_SPI_TIMING_TDC); + digitalWrite(sclkPin, HIGH); + DELAY_NS_VAR(MAX31865_SPI_TIMING_TCL - MAX31865_SPI_TIMING_TDC); + } + return reply; } -void MAX31865::softSpiBegin(const uint8_t spi_speed) { +void MAX31865::softSpiInit() { DEBUG_ECHOLNPGM("Initializing MAX31865 Software SPI"); - - #ifdef TARGET_LPC1768 - swSpiBegin(sclkPin, misoPin, mosiPin); - spiSpeed = swSpiInit(spi_speed, sclkPin, mosiPin); - #else - spiDelay = (100UL << spi_speed) / 3; // Calculate delay in ns. Top speed is ~10MHz, or 100ns delay between bits. - pinMode(sclkPin, OUTPUT); - digitalWrite(sclkPin, LOW); - pinMode(mosiPin, OUTPUT); - pinMode(misoPin, INPUT); - #endif + pinMode(sclkPin, OUTPUT); + digitalWrite(sclkPin, LOW); + pinMode(mosiPin, OUTPUT); + pinMode(misoPin, INPUT); } #endif // HAS_MAX31865 && !USE_ADAFRUIT_MAX31865 diff --git a/Marlin/src/libs/MAX31865.h b/Marlin/src/libs/MAX31865.h index bc7733b835..baea455485 100644 --- a/Marlin/src/libs/MAX31865.h +++ b/Marlin/src/libs/MAX31865.h @@ -101,11 +101,7 @@ private: TERN(LARGE_PINMAP, uint32_t, uint8_t) sclkPin, misoPin, mosiPin, cselPin; - #ifdef TARGET_LPC1768 - uint8_t spiSpeed; - #else - uint16_t spiDelay; - #endif + uint16_t spiDelay; float zeroRes, refRes, wireRes; @@ -121,6 +117,11 @@ private: one_shot_event_t nextEvent; #endif + #ifdef MAX31865_IGNORE_INITIAL_FAULTY_READS + uint8_t ignore_faults = MAX31865_IGNORE_INITIAL_FAULTY_READS; + uint16_t fixFault(uint16_t rtd); + #endif + uint8_t stdFlags = 0; void setConfig(uint8_t config, bool enable); @@ -130,9 +131,12 @@ private: uint16_t readRegister16(uint8_t addr); void writeRegister8(uint8_t addr, uint8_t reg); - uint8_t spiTransfer(uint8_t addr); + void writeRegister16(uint8_t addr, uint16_t reg); - void softSpiBegin(const uint8_t spi_speed); + void softSpiInit(); + void spiBeginTransaction(); + uint8_t spiTransfer(uint8_t addr); + void spiEndTransaction(); void initFixedFlags(max31865_numwires_t wires); @@ -141,6 +145,10 @@ private: void oneShot(); void resetFlags(); + uint16_t readRawImmediate(); + + void runAutoFaultDetectionCycle(); + public: #if ENABLED(LARGE_PINMAP) MAX31865(uint32_t spi_cs, uint8_t pin_mapping);