Merge pull request #3676 from thinkyhead/rc_lin_advance_feature
Advance extrusion algorithm – LIN_ADVANCE
This commit is contained in:
Scott Lahteine
GitHub
commit
587de1b6b6
|
|
@ -76,10 +76,12 @@ script:
|
|||
- build_marlin
|
||||
#
|
||||
# Test 3 extruders on RUMBA (can use any board with >=3 extruders defined)
|
||||
# Include a test for LIN_ADVANCE here also
|
||||
#
|
||||
- opt_set MOTHERBOARD BOARD_RUMBA
|
||||
- opt_set EXTRUDERS 3
|
||||
- opt_set TEMP_SENSOR_2 1
|
||||
- opt_enable_adv LIN_ADVANCE
|
||||
- build_marlin
|
||||
#
|
||||
# Test PIDTEMPBED
|
||||
|
|
|
|||
|
|
@ -445,6 +445,15 @@
|
|||
#define D_FILAMENT 2.85
|
||||
#endif
|
||||
|
||||
// Implementation of a linear pressure control
|
||||
// Assumption: advance = k * (delta velocity)
|
||||
// K=0 means advance disabled. A good value for a gregs wade extruder will be around K=75
|
||||
//#define LIN_ADVANCE
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
#define LIN_ADVANCE_K 75
|
||||
#endif
|
||||
|
||||
// @section leveling
|
||||
|
||||
// Default mesh area is an area with an inset margin on the print area.
|
||||
|
|
|
|||
|
|
@ -6475,6 +6475,16 @@ inline void gcode_M503() {
|
|||
|
||||
#endif // DUAL_X_CARRIAGE
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
/**
|
||||
* M905: Set advance factor
|
||||
*/
|
||||
inline void gcode_M905() {
|
||||
stepper.synchronize();
|
||||
stepper.advance_M905();
|
||||
}
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M907: Set digital trimpot motor current using axis codes X, Y, Z, E, B, S
|
||||
*/
|
||||
|
|
@ -7348,6 +7358,12 @@ void process_next_command() {
|
|||
break;
|
||||
#endif // DUAL_X_CARRIAGE
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
case 905: // M905 Set advance factor.
|
||||
gcode_M905();
|
||||
break;
|
||||
#endif
|
||||
|
||||
case 907: // M907 Set digital trimpot motor current using axis codes.
|
||||
gcode_M907();
|
||||
break;
|
||||
|
|
|
|||
|
|
@ -351,6 +351,13 @@
|
|||
|
||||
#endif // AUTO_BED_LEVELING_FEATURE
|
||||
|
||||
/**
|
||||
* Advance Extrusion
|
||||
*/
|
||||
#if ENABLED(ADVANCE) && ENABLED(LIN_ADVANCE)
|
||||
#error You can enable ADVANCE or LIN_ADVANCE, but not both.
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Filament Width Sensor
|
||||
*/
|
||||
|
|
@ -358,7 +365,6 @@
|
|||
#error "FILAMENT_WIDTH_SENSOR requires a FILWIDTH_PIN to be defined."
|
||||
#endif
|
||||
|
||||
|
||||
/**
|
||||
* ULTIPANEL encoder
|
||||
*/
|
||||
|
|
|
|||
|
|
@ -1050,7 +1050,23 @@ void Planner::check_axes_activity() {
|
|||
for (int i = 0; i < NUM_AXIS; i++) previous_speed[i] = current_speed[i];
|
||||
previous_nominal_speed = block->nominal_speed;
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
|
||||
// bse == allsteps: A problem occurs when there's a very tiny move before a retract.
|
||||
// In this case, the retract and the move will be executed together.
|
||||
// This leads to an enormous number of advance steps due to a huge e_acceleration.
|
||||
// The math is correct, but you don't want a retract move done with advance!
|
||||
// So this situation is filtered out here.
|
||||
if (!bse || (!bsx && !bsy && !bsz) || stepper.get_advance_k() == 0 || bse == allsteps) {
|
||||
block->use_advance_lead = false;
|
||||
}
|
||||
else {
|
||||
block->use_advance_lead = true;
|
||||
block->e_speed_multiplier8 = (block->steps[E_AXIS] << 8) / block->step_event_count;
|
||||
}
|
||||
|
||||
#elif ENABLED(ADVANCE)
|
||||
|
||||
// Calculate advance rate
|
||||
if (!bse || (!bsx && !bsy && !bsz)) {
|
||||
block->advance_rate = 0;
|
||||
|
|
@ -1069,7 +1085,8 @@ void Planner::check_axes_activity() {
|
|||
SERIAL_ECHOPGM("advance rate :");
|
||||
SERIAL_ECHOLN(block->advance_rate/256.0);
|
||||
*/
|
||||
#endif // ADVANCE
|
||||
|
||||
#endif // ADVANCE or LIN_ADVANCE
|
||||
|
||||
calculate_trapezoid_for_block(block, block->entry_speed / block->nominal_speed, safe_speed / block->nominal_speed);
|
||||
|
||||
|
|
|
|||
|
|
@ -64,7 +64,11 @@ typedef struct {
|
|||
|
||||
unsigned char direction_bits; // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
// Advance extrusion
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
bool use_advance_lead;
|
||||
int e_speed_multiplier8; // Factorised by 2^8 to avoid float
|
||||
#elif ENABLED(ADVANCE)
|
||||
long advance_rate;
|
||||
volatile long initial_advance;
|
||||
volatile long final_advance;
|
||||
|
|
|
|||
|
|
@ -89,13 +89,24 @@ long Stepper::counter_X = 0,
|
|||
|
||||
volatile unsigned long Stepper::step_events_completed = 0; // The number of step events executed in the current block
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#if ENABLED(ADVANCE) || ENABLED(LIN_ADVANCE)
|
||||
|
||||
unsigned char Stepper::old_OCR0A;
|
||||
long Stepper::final_advance = 0,
|
||||
volatile unsigned char Stepper::eISR_Rate = 200; // Keep the ISR at a low rate until needed
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
volatile int Stepper::e_steps[EXTRUDERS];
|
||||
int Stepper::extruder_advance_k = LIN_ADVANCE_K,
|
||||
Stepper::final_estep_rate,
|
||||
Stepper::current_estep_rate[EXTRUDERS],
|
||||
Stepper::current_adv_steps[EXTRUDERS];
|
||||
#else
|
||||
long Stepper::e_steps[EXTRUDERS],
|
||||
Stepper::final_advance = 0,
|
||||
Stepper::old_advance = 0,
|
||||
Stepper::e_steps[EXTRUDERS],
|
||||
Stepper::advance_rate,
|
||||
Stepper::advance;
|
||||
#endif
|
||||
#endif
|
||||
|
||||
long Stepper::acceleration_time, Stepper::deceleration_time;
|
||||
|
|
@ -344,13 +355,31 @@ void Stepper::isr() {
|
|||
customizedSerial.checkRx(); // Check for serial chars.
|
||||
#endif
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
|
||||
counter_E += current_block->steps[E_AXIS];
|
||||
if (counter_E > 0) {
|
||||
counter_E -= current_block->step_event_count;
|
||||
count_position[E_AXIS] += count_direction[E_AXIS];
|
||||
e_steps[current_block->active_extruder] += motor_direction(E_AXIS) ? -1 : 1;
|
||||
}
|
||||
|
||||
if (current_block->use_advance_lead) {
|
||||
int delta_adv_steps; //Maybe a char would be enough?
|
||||
delta_adv_steps = (((long)extruder_advance_k * current_estep_rate[current_block->active_extruder]) >> 9) - current_adv_steps[current_block->active_extruder];
|
||||
e_steps[current_block->active_extruder] += delta_adv_steps;
|
||||
current_adv_steps[current_block->active_extruder] += delta_adv_steps;
|
||||
}
|
||||
|
||||
#elif ENABLED(ADVANCE)
|
||||
|
||||
counter_E += current_block->steps[E_AXIS];
|
||||
if (counter_E > 0) {
|
||||
counter_E -= current_block->step_event_count;
|
||||
e_steps[current_block->active_extruder] += motor_direction(E_AXIS) ? -1 : 1;
|
||||
}
|
||||
#endif //ADVANCE
|
||||
|
||||
#endif // ADVANCE or LIN_ADVANCE
|
||||
|
||||
#define _COUNTER(AXIS) counter_## AXIS
|
||||
#define _APPLY_STEP(AXIS) AXIS ##_APPLY_STEP
|
||||
|
|
@ -363,7 +392,7 @@ void Stepper::isr() {
|
|||
STEP_ADD(X);
|
||||
STEP_ADD(Y);
|
||||
STEP_ADD(Z);
|
||||
#if DISABLED(ADVANCE)
|
||||
#if DISABLED(ADVANCE) && DISABLED(LIN_ADVANCE)
|
||||
STEP_ADD(E);
|
||||
#endif
|
||||
|
||||
|
|
@ -377,13 +406,19 @@ void Stepper::isr() {
|
|||
STEP_IF_COUNTER(X);
|
||||
STEP_IF_COUNTER(Y);
|
||||
STEP_IF_COUNTER(Z);
|
||||
#if DISABLED(ADVANCE)
|
||||
#if DISABLED(ADVANCE) && DISABLED(LIN_ADVANCE)
|
||||
STEP_IF_COUNTER(E);
|
||||
#endif
|
||||
|
||||
step_events_completed++;
|
||||
if (step_events_completed >= current_block->step_event_count) break;
|
||||
}
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
// If we have esteps to execute, fire the next ISR "now"
|
||||
if (e_steps[current_block->active_extruder]) OCR0A = TCNT0 + 2;
|
||||
#endif
|
||||
|
||||
// Calculate new timer value
|
||||
unsigned short timer, step_rate;
|
||||
if (step_events_completed <= (unsigned long)current_block->accelerate_until) {
|
||||
|
|
@ -399,7 +434,12 @@ void Stepper::isr() {
|
|||
OCR1A = timer;
|
||||
acceleration_time += timer;
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
|
||||
if (current_block->use_advance_lead)
|
||||
current_estep_rate[current_block->active_extruder] = ((unsigned long)acc_step_rate * current_block->e_speed_multiplier8) >> 8;
|
||||
|
||||
#elif ENABLED(ADVANCE)
|
||||
|
||||
advance += advance_rate * step_loops;
|
||||
//NOLESS(advance, current_block->advance);
|
||||
|
|
@ -408,7 +448,11 @@ void Stepper::isr() {
|
|||
e_steps[current_block->active_extruder] += ((advance >> 8) - old_advance);
|
||||
old_advance = advance >> 8;
|
||||
|
||||
#endif //ADVANCE
|
||||
#endif // ADVANCE or LIN_ADVANCE
|
||||
|
||||
#if ENABLED(ADVANCE) || ENABLED(LIN_ADVANCE)
|
||||
eISR_Rate = (timer >> 2) / abs(e_steps[current_block->active_extruder]);
|
||||
#endif
|
||||
}
|
||||
else if (step_events_completed > (unsigned long)current_block->decelerate_after) {
|
||||
MultiU24X32toH16(step_rate, deceleration_time, current_block->acceleration_rate);
|
||||
|
|
@ -425,7 +469,13 @@ void Stepper::isr() {
|
|||
OCR1A = timer;
|
||||
deceleration_time += timer;
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
|
||||
if (current_block->use_advance_lead)
|
||||
current_estep_rate[current_block->active_extruder] = ((unsigned long)step_rate * current_block->e_speed_multiplier8) >> 8;
|
||||
|
||||
#elif ENABLED(ADVANCE)
|
||||
|
||||
advance -= advance_rate * step_loops;
|
||||
NOLESS(advance, final_advance);
|
||||
|
||||
|
|
@ -433,9 +483,24 @@ void Stepper::isr() {
|
|||
uint32_t advance_whole = advance >> 8;
|
||||
e_steps[current_block->active_extruder] += advance_whole - old_advance;
|
||||
old_advance = advance_whole;
|
||||
#endif //ADVANCE
|
||||
|
||||
#endif // ADVANCE or LIN_ADVANCE
|
||||
|
||||
#if ENABLED(ADVANCE) || ENABLED(LIN_ADVANCE)
|
||||
eISR_Rate = (timer >> 2) / abs(e_steps[current_block->active_extruder]);
|
||||
#endif
|
||||
}
|
||||
else {
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
|
||||
if (current_block->use_advance_lead)
|
||||
current_estep_rate[current_block->active_extruder] = final_estep_rate;
|
||||
|
||||
eISR_Rate = (OCR1A_nominal >> 2) / abs(e_steps[current_block->active_extruder]);
|
||||
|
||||
#endif
|
||||
|
||||
OCR1A = OCR1A_nominal;
|
||||
// ensure we're running at the correct step rate, even if we just came off an acceleration
|
||||
step_loops = step_loops_nominal;
|
||||
|
|
@ -451,13 +516,15 @@ void Stepper::isr() {
|
|||
}
|
||||
}
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#if ENABLED(ADVANCE) || ENABLED(LIN_ADVANCE)
|
||||
|
||||
// Timer interrupt for E. e_steps is set in the main routine;
|
||||
// Timer 0 is shared with millies
|
||||
ISR(TIMER0_COMPA_vect) { Stepper::advance_isr(); }
|
||||
|
||||
void Stepper::advance_isr() {
|
||||
old_OCR0A += 52; // ~10kHz interrupt (250000 / 26 = 9615kHz)
|
||||
|
||||
old_OCR0A += eISR_Rate;
|
||||
OCR0A = old_OCR0A;
|
||||
|
||||
#define STEP_E_ONCE(INDEX) \
|
||||
|
|
@ -474,8 +541,7 @@ void Stepper::isr() {
|
|||
E## INDEX ##_STEP_WRITE(!INVERT_E_STEP_PIN); \
|
||||
}
|
||||
|
||||
// Step all E steppers that have steps, up to 4 steps per interrupt
|
||||
for (unsigned char i = 0; i < 4; i++) {
|
||||
// Step all E steppers that have steps
|
||||
STEP_E_ONCE(0);
|
||||
#if EXTRUDERS > 1
|
||||
STEP_E_ONCE(1);
|
||||
|
|
@ -486,10 +552,10 @@ void Stepper::isr() {
|
|||
#endif
|
||||
#endif
|
||||
#endif
|
||||
}
|
||||
|
||||
}
|
||||
|
||||
#endif // ADVANCE
|
||||
#endif // ADVANCE or LIN_ADVANCE
|
||||
|
||||
void Stepper::init() {
|
||||
|
||||
|
|
@ -656,14 +722,28 @@ void Stepper::init() {
|
|||
TCNT1 = 0;
|
||||
ENABLE_STEPPER_DRIVER_INTERRUPT();
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#if ENABLED(ADVANCE) || ENABLED(LIN_ADVANCE)
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
|
||||
for (int i = 0; i < EXTRUDERS; i++) {
|
||||
e_steps[i] = 0;
|
||||
current_adv_steps[i] = 0;
|
||||
}
|
||||
|
||||
#elif ENABLED(ADVANCE)
|
||||
|
||||
for (uint8_t i = 0; i < EXTRUDERS; i++) e_steps[i] = 0;
|
||||
|
||||
#endif
|
||||
|
||||
#if defined(TCCR0A) && defined(WGM01)
|
||||
CBI(TCCR0A, WGM01);
|
||||
CBI(TCCR0A, WGM00);
|
||||
#endif
|
||||
for (uint8_t i = 0; i < EXTRUDERS; i++) e_steps[i] = 0;
|
||||
SBI(TIMSK0, OCIE0A);
|
||||
#endif //ADVANCE
|
||||
|
||||
#endif // ADVANCE or LIN_ADVANCE
|
||||
|
||||
endstops.enable(true); // Start with endstops active. After homing they can be disabled
|
||||
sei();
|
||||
|
|
@ -1040,3 +1120,14 @@ void Stepper::microstep_readings() {
|
|||
SERIAL_PROTOCOLLN(digitalRead(E1_MS2_PIN));
|
||||
#endif
|
||||
}
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
|
||||
void Stepper::advance_M905() {
|
||||
if (code_seen('K')) extruder_advance_k = code_value();
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOPAIR("Advance factor: ", extruder_advance_k);
|
||||
SERIAL_EOL;
|
||||
}
|
||||
|
||||
#endif // LIN_ADVANCE
|
||||
|
|
|
|||
|
|
@ -22,7 +22,7 @@
|
|||
|
||||
/**
|
||||
* stepper.h - stepper motor driver: executes motion plans of planner.c using the stepper motors
|
||||
* Part of Grbl
|
||||
* Derived from Grbl
|
||||
*
|
||||
* Copyright (c) 2009-2011 Simen Svale Skogsrud
|
||||
*
|
||||
|
|
@ -90,10 +90,6 @@ class Stepper {
|
|||
static bool performing_homing;
|
||||
#endif
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
static long e_steps[EXTRUDERS];
|
||||
#endif
|
||||
|
||||
private:
|
||||
|
||||
static unsigned char last_direction_bits; // The next stepping-bits to be output
|
||||
|
|
@ -107,10 +103,23 @@ class Stepper {
|
|||
static long counter_X, counter_Y, counter_Z, counter_E;
|
||||
static volatile unsigned long step_events_completed; // The number of step events executed in the current block
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#if ENABLED(ADVANCE) || ENABLED(LIN_ADVANCE)
|
||||
static unsigned char old_OCR0A;
|
||||
static long advance_rate, advance, old_advance, final_advance;
|
||||
static volatile unsigned char eISR_Rate;
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
static volatile int e_steps[EXTRUDERS];
|
||||
static int extruder_advance_k;
|
||||
static int final_estep_rate;
|
||||
static int current_estep_rate[EXTRUDERS]; // Actual extruder speed [steps/s]
|
||||
static int current_adv_steps[EXTRUDERS]; // The amount of current added esteps due to advance.
|
||||
// i.e., the current amount of pressure applied
|
||||
// to the spring (=filament).
|
||||
#else
|
||||
static long e_steps[EXTRUDERS];
|
||||
static long advance_rate, advance, final_advance;
|
||||
static long old_advance;
|
||||
#endif
|
||||
#endif // ADVANCE or LIN_ADVANCE
|
||||
|
||||
static long acceleration_time, deceleration_time;
|
||||
//unsigned long accelerate_until, decelerate_after, acceleration_rate, initial_rate, final_rate, nominal_rate;
|
||||
|
|
@ -156,7 +165,7 @@ class Stepper {
|
|||
|
||||
static void isr();
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#if ENABLED(ADVANCE) || ENABLED(LIN_ADVANCE)
|
||||
static void advance_isr();
|
||||
#endif
|
||||
|
||||
|
|
@ -246,6 +255,11 @@ class Stepper {
|
|||
return endstops_trigsteps[axis] / planner.axis_steps_per_mm[axis];
|
||||
}
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
void advance_M905();
|
||||
FORCE_INLINE int get_advance_k() { return extruder_advance_k; }
|
||||
#endif
|
||||
|
||||
private:
|
||||
|
||||
static FORCE_INLINE unsigned short calc_timer(unsigned short step_rate) {
|
||||
|
|
@ -316,6 +330,13 @@ class Stepper {
|
|||
acceleration_time = calc_timer(acc_step_rate);
|
||||
OCR1A = acceleration_time;
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
if (current_block->use_advance_lead) {
|
||||
current_estep_rate[current_block->active_extruder] = ((unsigned long)acc_step_rate * current_block->e_speed_multiplier8) >> 8;
|
||||
final_estep_rate = (current_block->nominal_rate * current_block->e_speed_multiplier8) >> 8;
|
||||
}
|
||||
#endif
|
||||
|
||||
// SERIAL_ECHO_START;
|
||||
// SERIAL_ECHOPGM("advance :");
|
||||
// SERIAL_ECHO(current_block->advance/256.0);
|
||||
|
|
|
|||
Loading…
Reference in a new issue