diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 1cb7ea2de2..3d5cf2ef6b 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -43,6 +43,8 @@ // 82 = Brainwave (AT90USB646) // 9 = Gen3+ // 70 = Megatronics +// 701= Megatronics v2.0 +// 702= Minitronics v1.0 // 90 = Alpha OMCA board // 91 = Final OMCA board // 301 = Rambo @@ -54,6 +56,9 @@ // Define this to set a custom name for your generic Mendel, // #define CUSTOM_MENDEL_NAME "This Mendel" +// This defines the number of extruders +#define EXTRUDERS 1 + //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX // 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) @@ -81,24 +86,28 @@ // 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) // 10 is 100k RS thermistor 198-961 (4.7k pullup) // -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k +// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k // (but gives greater accuracy and more stable PID) // 51 is 100k thermistor - EPCOS (1k pullup) // 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) // 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan) (1k pullup) #define TEMP_SENSOR_0 -1 -#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_1 -1 #define TEMP_SENSOR_2 0 #define TEMP_SENSOR_BED 0 +// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + // Actual temperature must be close to target for this long before M109 returns success -#define TEMP_RESIDENCY_TIME 10 // (seconds) +#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. // The minimal temperature defines the temperature below which the heater will not be enabled It is used -// to check that the wiring to the thermistor is not broken. +// to check that the wiring to the thermistor is not broken. // Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5 @@ -124,7 +133,7 @@ #define BANG_MAX 256 // limits current to nozzle while in bang-bang mode; 256=full current #define PID_MAX 256 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 256=full current #ifdef PIDTEMP - //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. @@ -135,15 +144,15 @@ // If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it // Ultimaker #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 // Makergear // #define DEFAULT_Kp 7.0 -// #define DEFAULT_Ki 0.1 -// #define DEFAULT_Kd 12 +// #define DEFAULT_Ki 0.1 +// #define DEFAULT_Kd 12 -// Mendel Parts V9 on 12V +// Mendel Parts V9 on 12V // #define DEFAULT_Kp 63.0 // #define DEFAULT_Ki 2.25 // #define DEFAULT_Kd 440 @@ -155,8 +164,8 @@ // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. // If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz, // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. -// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. -// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably // shouldn't use bed PID until someone else verifies your hardware works. // If this is enabled, find your own PID constants below. //#define PIDTEMPBED @@ -226,9 +235,9 @@ #endif // The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins. -const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. -const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. -const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. +const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. +const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. +const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. //#define DISABLE_MAX_ENDSTOPS // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 @@ -283,13 +292,13 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) -// default settings +// default settings -#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) +#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker +#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) #define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). @@ -310,7 +319,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th // EEPROM // the microcontroller can store settings in the EEPROM, e.g. max velocity... // M500 - stores paramters in EEPROM -// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. //define this to enable eeprom support //#define EEPROM_SETTINGS @@ -318,9 +327,18 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th // please keep turned on if you can. //#define EEPROM_CHITCHAT +// Preheat Constants +#define PLA_PREHEAT_HOTEND_TEMP 180 +#define PLA_PREHEAT_HPB_TEMP 70 +#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 + +#define ABS_PREHEAT_HOTEND_TEMP 240 +#define ABS_PREHEAT_HPB_TEMP 100 +#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 + //LCD and SD support //#define ULTRA_LCD //general lcd support, also 16x2 -//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) +//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define SDSUPPORT // Enable SD Card Support in Hardware Console //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) @@ -341,6 +359,11 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER +// The RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click + //automatic expansion #if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define DOGLCD @@ -351,38 +374,74 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th #if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL) #define ULTIPANEL #define NEWPANEL -#endif +#endif -// Preheat Constants -#define PLA_PREHEAT_HOTEND_TEMP 180 -#define PLA_PREHEAT_HPB_TEMP 70 -#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 +#if defined(REPRAPWORLD_KEYPAD) + #define NEWPANEL + #define ULTIPANEL +#endif -#define ABS_PREHEAT_HOTEND_TEMP 240 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 +//I2C PANELS +//#define LCD_I2C_SAINSMART_YWROBOT +#ifdef LCD_I2C_SAINSMART_YWROBOT + // This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home ) + // Make sure it is placed in the Arduino libraries directory. + #define LCD_I2C_TYPE_PCF8575 + #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander + #define NEWPANEL + #define ULTIPANEL +#endif + +// PANELOLU2 LCD with status LEDs, separate encoder and click inputs +//#define LCD_I2C_PANELOLU2 +#ifdef LCD_I2C_PANELOLU2 + // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) + // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. + // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file) + // Note: The PANELOLU2 encoder click input can either be directly connected to a pin + // (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). + #define LCD_I2C_TYPE_MCP23017 + #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander + #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD + #define NEWPANEL + #define ULTIPANEL +#endif + +// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs +//#define LCD_I2C_VIKI +#ifdef LCD_I2C_VIKI + // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) + // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. + // Note: The pause/stop/resume LCD button pin should be connected to the Arduino + // BTN_ENC pin (or set BTN_ENC to -1 if not used) + #define LCD_I2C_TYPE_MCP23017 + #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander + #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later) + #define NEWPANEL + #define ULTIPANEL +#endif #ifdef ULTIPANEL // #define NEWPANEL //enable this if you have a click-encoder panel #define SDSUPPORT #define ULTRA_LCD - #ifdef DOGLCD // Change number of lines to match the DOG graphic display - #define LCD_WIDTH 20 - #define LCD_HEIGHT 5 - #else - #define LCD_WIDTH 20 - #define LCD_HEIGHT 4 - #endif -#else //no panel but just lcd + #ifdef DOGLCD // Change number of lines to match the DOG graphic display + #define LCD_WIDTH 20 + #define LCD_HEIGHT 5 + #else + #define LCD_WIDTH 20 + #define LCD_HEIGHT 4 + #endif +#else //no panel but just lcd #ifdef ULTRA_LCD - #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display - #define LCD_WIDTH 20 - #define LCD_HEIGHT 5 - #else - #define LCD_WIDTH 16 - #define LCD_HEIGHT 2 - #endif + #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display + #define LCD_WIDTH 20 + #define LCD_HEIGHT 5 + #else + #define LCD_WIDTH 16 + #define LCD_HEIGHT 2 + #endif #endif #endif @@ -396,6 +455,26 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th // SF send wrong arc g-codes when using Arc Point as fillet procedure //#define SF_ARC_FIX +// Support for the BariCUDA Paste Extruder. +//#define BARICUDA + +/*********************************************************************\ +* +* R/C SERVO support +* +* Sponsored by TrinityLabs, Reworked by codexmas +* +**********************************************************************/ + +// Number of servos +// +// If you select a configuration below, this will receive a default value and does not need to be set manually +// set it manually if you have more servos than extruders and wish to manually control some +// leaving it undefined or defining as 0 will disable the servo subsystem +// If unsure, leave commented / disabled +// +// #define NUM_SERVOS 3 + #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 7fc95b9979..5f1c77a056 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -63,21 +63,31 @@ //This is for controlling a fan to cool down the stepper drivers //it will turn on when any driver is enabled //and turn off after the set amount of seconds from last driver being disabled again -//#define CONTROLLERFAN_PIN 23 //Pin used for the fan to cool controller, comment out to disable this function -#define CONTROLLERFAN_SEC 60 //How many seconds, after all motors were disabled, the fan should run +#define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller (-1 to disable) +#define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run +#define CONTROLLERFAN_SPEED 255 // == full speed // When first starting the main fan, run it at full speed for the // given number of milliseconds. This gets the fan spinning reliably // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) //#define FAN_KICKSTART_TIME 100 +// Extruder cooling fans +// Configure fan pin outputs to automatically turn on/off when the associated +// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE. +// Multiple extruders can be assigned to the same pin in which case +// the fan will turn on when any selected extruder is above the threshold. +#define EXTRUDER_0_AUTO_FAN_PIN -1 +#define EXTRUDER_1_AUTO_FAN_PIN -1 +#define EXTRUDER_2_AUTO_FAN_PIN -1 +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed + + //=========================================================================== //=============================Mechanical Settings=========================== //=========================================================================== -// This defines the number of extruders -#define EXTRUDERS 1 - #define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing @@ -210,9 +220,9 @@ // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. //#define WATCHDOG_RESET_MANUAL #endif - -// Enable the option to stop SD printing when hitting and endstops, needs to be enabled from the LCD menu when this option is enabled. -//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED + +// Enable the option to stop SD printing when hitting and endstops, needs to be enabled from the LCD menu when this option is enabled. +//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED // extruder advance constant (s2/mm3) // @@ -276,7 +286,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #else #define BLOCK_BUFFER_SIZE 16 // maximize block buffer #endif - + //The ASCII buffer for recieving from the serial: #define MAX_CMD_SIZE 96 @@ -308,6 +318,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st //=========================================================================== //============================= Define Defines ============================ //=========================================================================== +#if EXTRUDERS > 1 && defined TEMP_SENSOR_1_AS_REDUNDANT + #error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1" +#endif #if TEMP_SENSOR_0 > 0 #define THERMISTORHEATER_0 TEMP_SENSOR_0 diff --git a/Marlin/DOGMbitmaps.h b/Marlin/DOGMbitmaps.h index a5d8702cda..984f421c0a 100644 --- a/Marlin/DOGMbitmaps.h +++ b/Marlin/DOGMbitmaps.h @@ -1,7 +1,7 @@ #define START_BMPWIDTH 60 //Width in pixels #define START_BMPHEIGHT 64 //Height in pixels #define START_BMPBYTEWIDTH 8 //Width in bytes -unsigned char start_bmp[574] PROGMEM = { //AVR-GCC, WinAVR +const unsigned char start_bmp[574] PROGMEM = { //AVR-GCC, WinAVR 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF0, 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF0, 0xFF,0xFF,0xFF,0xF9,0xFF,0xFF,0xFF,0xF0, @@ -71,7 +71,7 @@ unsigned char start_bmp[574] PROGMEM = { //AVR-GCC, WinAVR #define STATUS_SCREENWIDTH 115 //Width in pixels #define STATUS_SCREENHEIGHT 19 //Height in pixels #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes -unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR +const unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x0C,0x60, @@ -96,7 +96,7 @@ unsigned char status_screen0_bmp[] PROGMEM = { //AVR-GCC, WinAVR #define STATUS_SCREENWIDTH 115 //Width in pixels #define STATUS_SCREENHEIGHT 19 //Height in pixels #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes -unsigned char status_screen1_bmp[] PROGMEM = { //AVR-GCC, WinAVR +const unsigned char status_screen1_bmp[] PROGMEM = { //AVR-GCC, WinAVR 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFF,0xE0, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0xE0, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x61,0xF8,0x60, diff --git a/Marlin/Makefile b/Marlin/Makefile index e09d15f067..c231735255 100644 --- a/Marlin/Makefile +++ b/Marlin/Makefile @@ -1,12 +1,12 @@ # Sprinter Arduino Project Makefile -# +# # Makefile Based on: # Arduino 0011 Makefile # Arduino adaptation by mellis, eighthave, oli.keller # Marlin adaption by Daid # # This has been tested with Arduino 0022. -# +# # This makefile allows you to build sketches from the command line # without the Arduino environment (or Java). # @@ -21,7 +21,7 @@ # (e.g. UPLOAD_PORT = /dev/tty.USB0). If the exact name of this file # changes, you can use * as a wildcard (e.g. UPLOAD_PORT = /dev/tty.usb*). # -# 3. Set the line containing "MCU" to match your board's processor. +# 3. Set the line containing "MCU" to match your board's processor. # Older one's are atmega8 based, newer ones like Arduino Mini, Bluetooth # or Diecimila have the atmega168. If you're using a LilyPad Arduino, # change F_CPU to 8000000. If you are using Gen7 electronics, you @@ -44,7 +44,7 @@ ARDUINO_INSTALL_DIR ?= ../../arduino-0022 ARDUINO_VERSION ?= 22 # You can optionally set a path to the avr-gcc tools. Requires a trailing slash. (ex: /usr/local/avr-gcc/bin) -AVR_TOOLS_PATH ?= +AVR_TOOLS_PATH ?= #Programmer configuration UPLOAD_RATE ?= 115200 @@ -213,7 +213,7 @@ CXXSRC = WMath.cpp WString.cpp Print.cpp Marlin_main.cpp \ SdFile.cpp SdVolume.cpp motion_control.cpp planner.cpp \ stepper.cpp temperature.cpp cardreader.cpp ConfigurationStore.cpp \ watchdog.cpp -CXXSRC += LiquidCrystal.cpp ultralcd.cpp SPI.cpp +CXXSRC += LiquidCrystal.cpp ultralcd.cpp SPI.cpp Servo.cpp #Check for Arduino 1.0.0 or higher and use the correct sourcefiles for that version ifeq ($(shell [ $(ARDUINO_VERSION) -ge 100 ] && echo true), true) @@ -317,19 +317,19 @@ endif # Default target. all: sizeafter -build: $(BUILD_DIR) elf hex +build: $(BUILD_DIR) elf hex # Creates the object directory -$(BUILD_DIR): +$(BUILD_DIR): $P mkdir -p $(BUILD_DIR) elf: $(BUILD_DIR)/$(TARGET).elf hex: $(BUILD_DIR)/$(TARGET).hex eep: $(BUILD_DIR)/$(TARGET).eep -lss: $(BUILD_DIR)/$(TARGET).lss +lss: $(BUILD_DIR)/$(TARGET).lss sym: $(BUILD_DIR)/$(TARGET).sym -# Program the device. +# Program the device. # Do not try to reset an arduino if it's not one upload: $(BUILD_DIR)/$(TARGET).hex ifeq (${AVRDUDE_PROGRAMMER}, arduino) @@ -356,7 +356,7 @@ COFFCONVERT=$(OBJCOPY) --debugging \ --change-section-address .data-0x800000 \ --change-section-address .bss-0x800000 \ --change-section-address .noinit-0x800000 \ - --change-section-address .eeprom-0x810000 + --change-section-address .eeprom-0x810000 coff: $(BUILD_DIR)/$(TARGET).elf diff --git a/Marlin/Marlin.h b/Marlin/Marlin.h index 25c5aca636..2e87d7b2ea 100644 --- a/Marlin/Marlin.h +++ b/Marlin/Marlin.h @@ -96,7 +96,7 @@ void process_commands(); void manage_inactivity(); -#if X_ENABLE_PIN > -1 +#if defined(X_ENABLE_PIN) && X_ENABLE_PIN > -1 #define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON) #define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON) #else @@ -104,7 +104,7 @@ void manage_inactivity(); #define disable_x() ; #endif -#if Y_ENABLE_PIN > -1 +#if defined(Y_ENABLE_PIN) && Y_ENABLE_PIN > -1 #define enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON) #define disable_y() WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON) #else @@ -112,7 +112,7 @@ void manage_inactivity(); #define disable_y() ; #endif -#if Z_ENABLE_PIN > -1 +#if defined(Z_ENABLE_PIN) && Z_ENABLE_PIN > -1 #ifdef Z_DUAL_STEPPER_DRIVERS #define enable_z() { WRITE(Z_ENABLE_PIN, Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN, Z_ENABLE_ON); } #define disable_z() { WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN,!Z_ENABLE_ON); } @@ -186,6 +186,10 @@ extern float add_homeing[3]; extern float min_pos[3]; extern float max_pos[3]; extern int fanSpeed; +#ifdef BARICUDA +extern int ValvePressure; +extern int EtoPPressure; +#endif #ifdef FWRETRACT extern bool autoretract_enabled; diff --git a/Marlin/Marlin.pde b/Marlin/Marlin.pde index 4d7d0a2fd7..2d6211c971 100644 --- a/Marlin/Marlin.pde +++ b/Marlin/Marlin.pde @@ -34,13 +34,19 @@ #include "pins.h" #ifdef ULTRA_LCD - #ifdef DOGLCD - #include // library for graphics LCD by Oli Kraus (https://code.google.com/p/u8glib/) - #else - #include // library for character LCD - #endif + #if defined(LCD_I2C_TYPE_PCF8575) + #include + #include + #elif defined(LCD_I2C_TYPE_MCP23017) || defined(LCD_I2C_TYPE_MCP23008) + #include + #include + #elif defined(DOGLCD) + #include // library for graphics LCD by Oli Kraus (https://code.google.com/p/u8glib/) + #else + #include // library for character LCD + #endif #endif -#if DIGIPOTSS_PIN > -1 +#if defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1 #include #endif diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp index 5917cbd081..39a7315ee4 100644 --- a/Marlin/Marlin_main.cpp +++ b/Marlin/Marlin_main.cpp @@ -3,17 +3,17 @@ /* Reprap firmware based on Sprinter and grbl. Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm - + This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. - + This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - + You should have received a copy of the GNU General Public License along with this program. If not, see . */ @@ -22,8 +22,8 @@ This firmware is a mashup between Sprinter and grbl. (https://github.com/kliment/Sprinter) (https://github.com/simen/grbl/tree) - - It has preliminary support for Matthew Roberts advance algorithm + + It has preliminary support for Matthew Roberts advance algorithm http://reprap.org/pipermail/reprap-dev/2011-May/003323.html */ @@ -40,7 +40,11 @@ #include "language.h" #include "pins_arduino.h" -#if DIGIPOTSS_PIN > -1 +#if NUM_SERVOS > 0 +#include "Servo.h" +#endif + +#if defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1 #include #endif @@ -93,14 +97,18 @@ // M81 - Turn off Power Supply // M82 - Set E codes absolute (default) // M83 - Set E codes relative while in Absolute Coordinates (G90) mode -// M84 - Disable steppers until next move, +// M84 - Disable steppers until next move, // or use S to specify an inactivity timeout, after which the steppers will be disabled. S0 to disable the timeout. // M85 - Set inactivity shutdown timer with parameter S. To disable set zero (default) // M92 - Set axis_steps_per_unit - same syntax as G92 -// M114 - Output current position to serial port -// M115 - Capabilities string +// M114 - Output current position to serial port +// M115 - Capabilities string // M117 - display message // M119 - Output Endstop status to serial port +// M126 - Solenoid Air Valve Open (BariCUDA support by jmil) +// M127 - Solenoid Air Valve Closed (BariCUDA vent to atmospheric pressure by jmil) +// M128 - EtoP Open (BariCUDA EtoP = electricity to air pressure transducer by jmil) +// M129 - EtoP Closed (BariCUDA EtoP = electricity to air pressure transducer by jmil) // M140 - Set bed target temp // M190 - Wait for bed current temp to reach target temp. // M200 - Set filament diameter @@ -117,14 +125,15 @@ // M220 S- set speed factor override percentage // M221 S- set extrude factor override percentage // M240 - Trigger a camera to take a photograph +// M280 - set servo position absolute. P: servo index, S: angle or microseconds // M300 - Play beepsound S P // M301 - Set PID parameters P I and D -// M302 - Allow cold extrudes +// M302 - Allow cold extrudes, or set the minimum extrude S. // M303 - PID relay autotune S sets the target temperature. (default target temperature = 150C) // M304 - Set bed PID parameters P I and D // M400 - Finish all moves // M500 - stores paramters in EEPROM -// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. // M503 - print the current settings (from memory not from eeprom) // M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) @@ -160,14 +169,18 @@ float min_pos[3] = { X_MIN_POS, Y_MIN_POS, Z_MIN_POS }; float max_pos[3] = { X_MAX_POS, Y_MAX_POS, Z_MAX_POS }; // Extruder offset, only in XY plane #if EXTRUDERS > 1 -float extruder_offset[2][EXTRUDERS] = { +float extruder_offset[2][EXTRUDERS] = { #if defined(EXTRUDER_OFFSET_X) && defined(EXTRUDER_OFFSET_Y) - EXTRUDER_OFFSET_X, EXTRUDER_OFFSET_Y + EXTRUDER_OFFSET_X, EXTRUDER_OFFSET_Y #endif -}; +}; #endif uint8_t active_extruder = 0; int fanSpeed=0; +#ifdef BARICUDA +int ValvePressure=0; +int EtoPPressure=0; +#endif #ifdef FWRETRACT bool autoretract_enabled=true; @@ -217,6 +230,10 @@ static uint8_t tmp_extruder; bool Stopped=false; +#if NUM_SERVOS > 0 + Servo servos[NUM_SERVOS]; +#endif + //=========================================================================== //=============================ROUTINES============================= //=========================================================================== @@ -283,49 +300,62 @@ void enquecommand_P(const char *cmd) void setup_killpin() { - #if( KILL_PIN>-1 ) + #if defined(KILL_PIN) && KILL_PIN > -1 pinMode(KILL_PIN,INPUT); WRITE(KILL_PIN,HIGH); #endif } - + void setup_photpin() { - #ifdef PHOTOGRAPH_PIN - #if (PHOTOGRAPH_PIN > -1) + #if defined(PHOTOGRAPH_PIN) && PHOTOGRAPH_PIN > -1 SET_OUTPUT(PHOTOGRAPH_PIN); WRITE(PHOTOGRAPH_PIN, LOW); - #endif - #endif + #endif } void setup_powerhold() { - #ifdef SUICIDE_PIN - #if (SUICIDE_PIN> -1) - SET_OUTPUT(SUICIDE_PIN); - WRITE(SUICIDE_PIN, HIGH); - #endif - #endif - #if (PS_ON_PIN > -1) - SET_OUTPUT(PS_ON_PIN); - WRITE(PS_ON_PIN, PS_ON_AWAKE); - #endif + #if defined(SUICIDE_PIN) && SUICIDE_PIN > -1 + SET_OUTPUT(SUICIDE_PIN); + WRITE(SUICIDE_PIN, HIGH); + #endif + #if defined(PS_ON_PIN) && PS_ON_PIN > -1 + SET_OUTPUT(PS_ON_PIN); + WRITE(PS_ON_PIN, PS_ON_AWAKE); + #endif } void suicide() { - #ifdef SUICIDE_PIN - #if (SUICIDE_PIN> -1) - SET_OUTPUT(SUICIDE_PIN); - WRITE(SUICIDE_PIN, LOW); - #endif + #if defined(SUICIDE_PIN) && SUICIDE_PIN > -1 + SET_OUTPUT(SUICIDE_PIN); + WRITE(SUICIDE_PIN, LOW); + #endif +} + +void servo_init() +{ + #if (NUM_SERVOS >= 1) && defined(SERVO0_PIN) && (SERVO0_PIN > -1) + servos[0].attach(SERVO0_PIN); + #endif + #if (NUM_SERVOS >= 2) && defined(SERVO1_PIN) && (SERVO1_PIN > -1) + servos[1].attach(SERVO1_PIN); + #endif + #if (NUM_SERVOS >= 3) && defined(SERVO2_PIN) && (SERVO2_PIN > -1) + servos[2].attach(SERVO2_PIN); + #endif + #if (NUM_SERVOS >= 4) && defined(SERVO3_PIN) && (SERVO3_PIN > -1) + servos[3].attach(SERVO3_PIN); + #endif + #if (NUM_SERVOS >= 5) + #error "TODO: enter initalisation code for more servos" #endif } void setup() { - setup_killpin(); + setup_killpin(); setup_powerhold(); MYSERIAL.begin(BAUDRATE); SERIAL_PROTOCOLLNPGM("start"); @@ -362,25 +392,22 @@ void setup() { fromsd[i] = false; } - - // loads data from EEPROM if available else uses defaults (and resets step acceleration rate) - Config_RetrieveSettings(); - tp_init(); // Initialize temperature loop + // loads data from EEPROM if available else uses defaults (and resets step acceleration rate) + Config_RetrieveSettings(); + + tp_init(); // Initialize temperature loop plan_init(); // Initialize planner; watchdog_init(); st_init(); // Initialize stepper, this enables interrupts! setup_photpin(); - + servo_init(); + lcd_init(); - - #ifdef CONTROLLERFAN_PIN + + #if defined(CONTROLLERFAN_PIN) && CONTROLLERFAN_PIN > -1 SET_OUTPUT(CONTROLLERFAN_PIN); //Set pin used for driver cooling fan #endif - - #ifdef EXTRUDERFAN_PIN - SET_OUTPUT(EXTRUDERFAN_PIN); //Set pin used for extruder cooling fan - #endif } @@ -396,9 +423,9 @@ void loop() #ifdef SDSUPPORT if(card.saving) { - if(strstr_P(cmdbuffer[bufindr], PSTR("M29")) == NULL) - { - card.write_command(cmdbuffer[bufindr]); + if(strstr_P(cmdbuffer[bufindr], PSTR("M29")) == NULL) + { + card.write_command(cmdbuffer[bufindr]); if(card.logging) { process_commands(); @@ -407,16 +434,16 @@ void loop() { SERIAL_PROTOCOLLNPGM(MSG_OK); } - } - else - { - card.closefile(); - SERIAL_PROTOCOLLNPGM(MSG_FILE_SAVED); - } + } + else + { + card.closefile(); + SERIAL_PROTOCOLLNPGM(MSG_FILE_SAVED); + } } else { - process_commands(); + process_commands(); } #else process_commands(); @@ -431,14 +458,14 @@ void loop() lcd_update(); } -void get_command() -{ +void get_command() +{ while( MYSERIAL.available() > 0 && buflen < BUFSIZE) { serial_char = MYSERIAL.read(); - if(serial_char == '\n' || - serial_char == '\r' || - (serial_char == ':' && comment_mode == false) || - serial_count >= (MAX_CMD_SIZE - 1) ) + if(serial_char == '\n' || + serial_char == '\r' || + (serial_char == ':' && comment_mode == false) || + serial_count >= (MAX_CMD_SIZE - 1) ) { if(!serial_count) { //if empty line comment_mode = false; //for new command @@ -479,7 +506,7 @@ void get_command() } //if no errors, continue parsing } - else + else { SERIAL_ERROR_START; SERIAL_ERRORPGM(MSG_ERR_NO_CHECKSUM); @@ -511,11 +538,11 @@ void get_command() case 2: case 3: if(Stopped == false) { // If printer is stopped by an error the G[0-3] codes are ignored. - #ifdef SDSUPPORT + #ifdef SDSUPPORT if(card.saving) break; - #endif //SDSUPPORT - SERIAL_PROTOCOLLNPGM(MSG_OK); + #endif //SDSUPPORT + SERIAL_PROTOCOLLNPGM(MSG_OK); } else { SERIAL_ERRORLNPGM(MSG_ERR_STOPPED); @@ -545,10 +572,10 @@ void get_command() while( !card.eof() && buflen < BUFSIZE) { int16_t n=card.get(); serial_char = (char)n; - if(serial_char == '\n' || - serial_char == '\r' || - (serial_char == ':' && comment_mode == false) || - serial_count >= (MAX_CMD_SIZE - 1)||n==-1) + if(serial_char == '\n' || + serial_char == '\r' || + (serial_char == ':' && comment_mode == false) || + serial_count >= (MAX_CMD_SIZE - 1)||n==-1) { if(card.eof()){ SERIAL_PROTOCOLLNPGM(MSG_FILE_PRINTED); @@ -564,7 +591,7 @@ void get_command() lcd_setstatus(time); card.printingHasFinished(); card.checkautostart(true); - + } if(!serial_count) { @@ -576,7 +603,7 @@ void get_command() fromsd[bufindw] = true; buflen += 1; bufindw = (bufindw + 1)%BUFSIZE; -// } +// } comment_mode = false; //for new command serial_count = 0; //clear buffer } @@ -586,20 +613,20 @@ void get_command() if(!comment_mode) cmdbuffer[bufindw][serial_count++] = serial_char; } } - + #endif //SDSUPPORT } -float code_value() -{ - return (strtod(&cmdbuffer[bufindr][strchr_pointer - cmdbuffer[bufindr] + 1], NULL)); +float code_value() +{ + return (strtod(&cmdbuffer[bufindr][strchr_pointer - cmdbuffer[bufindr] + 1], NULL)); } -long code_value_long() -{ - return (strtol(&cmdbuffer[bufindr][strchr_pointer - cmdbuffer[bufindr] + 1], NULL, 10)); +long code_value_long() +{ + return (strtol(&cmdbuffer[bufindr][strchr_pointer - cmdbuffer[bufindr] + 1], NULL, 10)); } bool code_seen(char code) @@ -608,17 +635,17 @@ bool code_seen(char code) return (strchr_pointer != NULL); //Return True if a character was found } -#define DEFINE_PGM_READ_ANY(type, reader) \ - static inline type pgm_read_any(const type *p) \ - { return pgm_read_##reader##_near(p); } +#define DEFINE_PGM_READ_ANY(type, reader) \ + static inline type pgm_read_any(const type *p) \ + { return pgm_read_##reader##_near(p); } DEFINE_PGM_READ_ANY(float, float); DEFINE_PGM_READ_ANY(signed char, byte); -#define XYZ_CONSTS_FROM_CONFIG(type, array, CONFIG) \ -static const PROGMEM type array##_P[3] = \ - { X_##CONFIG, Y_##CONFIG, Z_##CONFIG }; \ -static inline type array(int axis) \ +#define XYZ_CONSTS_FROM_CONFIG(type, array, CONFIG) \ +static const PROGMEM type array##_P[3] = \ + { X_##CONFIG, Y_##CONFIG, Z_##CONFIG }; \ +static inline type array(int axis) \ { return pgm_read_any(&array##_P[axis]); } XYZ_CONSTS_FROM_CONFIG(float, base_min_pos, MIN_POS); @@ -648,19 +675,19 @@ static void homeaxis(int axis) { feedrate = homing_feedrate[axis]; plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); st_synchronize(); - + current_position[axis] = 0; plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); destination[axis] = -home_retract_mm(axis) * home_dir(axis); plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); st_synchronize(); - + destination[axis] = 2*home_retract_mm(axis) * home_dir(axis); - feedrate = homing_feedrate[axis]/2 ; + feedrate = homing_feedrate[axis]/2 ; plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); st_synchronize(); - - axis_is_at_home(axis); + + axis_is_at_home(axis); destination[axis] = current_position[axis]; feedrate = 0.0; endstops_hit_on_purpose(); @@ -703,7 +730,7 @@ void process_commands() codenum = 0; if(code_seen('P')) codenum = code_value(); // milliseconds to wait if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait - + st_synchronize(); codenum += millis(); // keep track of when we started waiting previous_millis_cmd = millis(); @@ -713,30 +740,30 @@ void process_commands() lcd_update(); } break; - #ifdef FWRETRACT + #ifdef FWRETRACT case 10: // G10 retract - if(!retracted) + if(!retracted) { destination[X_AXIS]=current_position[X_AXIS]; destination[Y_AXIS]=current_position[Y_AXIS]; - destination[Z_AXIS]=current_position[Z_AXIS]; + destination[Z_AXIS]=current_position[Z_AXIS]; current_position[Z_AXIS]+=-retract_zlift; - destination[E_AXIS]=current_position[E_AXIS]-retract_length; + destination[E_AXIS]=current_position[E_AXIS]-retract_length; feedrate=retract_feedrate; retracted=true; prepare_move(); } - + break; case 11: // G10 retract_recover - if(!retracted) + if(!retracted) { destination[X_AXIS]=current_position[X_AXIS]; destination[Y_AXIS]=current_position[Y_AXIS]; - destination[Z_AXIS]=current_position[Z_AXIS]; - + destination[Z_AXIS]=current_position[Z_AXIS]; + current_position[Z_AXIS]+=retract_zlift; - current_position[E_AXIS]+=-retract_recover_length; + current_position[E_AXIS]+=-retract_recover_length; feedrate=retract_recover_feedrate; retracted=false; prepare_move(); @@ -748,34 +775,34 @@ void process_commands() saved_feedmultiply = feedmultiply; feedmultiply = 100; previous_millis_cmd = millis(); - + enable_endstops(true); - + for(int8_t i=0; i < NUM_AXIS; i++) { destination[i] = current_position[i]; } feedrate = 0.0; home_all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2]))); - + #if Z_HOME_DIR > 0 // If homing away from BED do Z first if((home_all_axis) || (code_seen(axis_codes[Z_AXIS]))) { HOMEAXIS(Z); } #endif - + #ifdef QUICK_HOME if((home_all_axis)||( code_seen(axis_codes[X_AXIS]) && code_seen(axis_codes[Y_AXIS])) ) //first diagonal move { - current_position[X_AXIS] = 0;current_position[Y_AXIS] = 0; + current_position[X_AXIS] = 0;current_position[Y_AXIS] = 0; - plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); - destination[X_AXIS] = 1.5 * X_MAX_LENGTH * X_HOME_DIR;destination[Y_AXIS] = 1.5 * Y_MAX_LENGTH * Y_HOME_DIR; - feedrate = homing_feedrate[X_AXIS]; + plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); + destination[X_AXIS] = 1.5 * X_MAX_LENGTH * X_HOME_DIR;destination[Y_AXIS] = 1.5 * Y_MAX_LENGTH * Y_HOME_DIR; + feedrate = homing_feedrate[X_AXIS]; if(homing_feedrate[Y_AXIS] 0){ codenum += millis(); // keep track of when we started waiting - while(millis() < codenum && !LCD_CLICKED){ + while(millis() < codenum && !lcd_clicked()){ manage_heater(); manage_inactivity(); lcd_update(); } }else{ - while(!LCD_CLICKED){ + while(!lcd_clicked()){ manage_heater(); manage_inactivity(); lcd_update(); @@ -892,12 +919,12 @@ void process_commands() #endif case 17: LCD_MESSAGEPGM(MSG_NO_MOVE); - enable_x(); - enable_y(); - enable_z(); - enable_e0(); - enable_e1(); - enable_e2(); + enable_x(); + enable_y(); + enable_z(); + enable_e0(); + enable_e1(); + enable_e2(); break; #ifdef SDSUPPORT @@ -907,9 +934,9 @@ void process_commands() SERIAL_PROTOCOLLNPGM(MSG_END_FILE_LIST); break; case 21: // M21 - init SD card - + card.initsd(); - + break; case 22: //M22 - release SD card card.release(); @@ -949,18 +976,18 @@ void process_commands() //processed in write to file routine above //card,saving = false; break; - case 30: //M30 Delete File - if (card.cardOK){ - card.closefile(); - starpos = (strchr(strchr_pointer + 4,'*')); - if(starpos != NULL){ - char* npos = strchr(cmdbuffer[bufindr], 'N'); - strchr_pointer = strchr(npos,' ') + 1; - *(starpos-1) = '\0'; - } - card.removeFile(strchr_pointer + 4); - } - break; + case 30: //M30 Delete File + if (card.cardOK){ + card.closefile(); + starpos = (strchr(strchr_pointer + 4,'*')); + if(starpos != NULL){ + char* npos = strchr(cmdbuffer[bufindr], 'N'); + strchr_pointer = strchr(npos,' ') + 1; + *(starpos-1) = '\0'; + } + card.removeFile(strchr_pointer + 4); + } + break; case 928: //M928 - Start SD write starpos = (strchr(strchr_pointer + 5,'*')); if(starpos != NULL){ @@ -970,7 +997,7 @@ void process_commands() } card.openLogFile(strchr_pointer+5); break; - + #endif //SDSUPPORT case 31: //M31 take time since the start of the SD print or an M109 command @@ -1003,6 +1030,10 @@ void process_commands() break; } } + #if defined(FAN_PIN) && FAN_PIN > -1 + if (pin_number == FAN_PIN) + fanSpeed = pin_status; + #endif if (pin_number > -1) { pinMode(pin_number, OUTPUT); @@ -1024,14 +1055,14 @@ void process_commands() case 105 : // M105 if(setTargetedHotend(105)){ break; - } - #if (TEMP_0_PIN > -1) + } + #if defined(TEMP_0_PIN) && TEMP_0_PIN > -1 SERIAL_PROTOCOLPGM("ok T:"); - SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1); + SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1); SERIAL_PROTOCOLPGM(" /"); - SERIAL_PROTOCOL_F(degTargetHotend(tmp_extruder),1); - #if TEMP_BED_PIN > -1 - SERIAL_PROTOCOLPGM(" B:"); + SERIAL_PROTOCOL_F(degTargetHotend(tmp_extruder),1); + #if defined(TEMP_BED_PIN) && TEMP_BED_PIN > -1 + SERIAL_PROTOCOLPGM(" B:"); SERIAL_PROTOCOL_F(degBed(),1); SERIAL_PROTOCOLPGM(" /"); SERIAL_PROTOCOL_F(degTargetBed(),1); @@ -1042,20 +1073,20 @@ void process_commands() #endif SERIAL_PROTOCOLPGM(" @:"); - SERIAL_PROTOCOL(getHeaterPower(tmp_extruder)); + SERIAL_PROTOCOL(getHeaterPower(tmp_extruder)); SERIAL_PROTOCOLPGM(" B@:"); - SERIAL_PROTOCOL(getHeaterPower(-1)); + SERIAL_PROTOCOL(getHeaterPower(-1)); SERIAL_PROTOCOLLN(""); return; break; - case 109: + case 109: {// M109 - Wait for extruder heater to reach target. if(setTargetedHotend(109)){ break; } - LCD_MESSAGEPGM(MSG_HEATING); + LCD_MESSAGEPGM(MSG_HEATING); #ifdef AUTOTEMP autotemp_enabled=false; #endif @@ -1063,15 +1094,15 @@ void process_commands() #ifdef AUTOTEMP if (code_seen('S')) autotemp_min=code_value(); if (code_seen('B')) autotemp_max=code_value(); - if (code_seen('F')) + if (code_seen('F')) { autotemp_factor=code_value(); autotemp_enabled=true; } #endif - + setWatch(); - codenum = millis(); + codenum = millis(); /* See if we are heating up or cooling down */ bool target_direction = isHeatingHotend(tmp_extruder); // true if heating, false if cooling @@ -1079,7 +1110,7 @@ void process_commands() #ifdef TEMP_RESIDENCY_TIME long residencyStart; residencyStart = -1; - /* continue to loop until we have reached the target temp + /* continue to loop until we have reached the target temp _and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */ while((residencyStart == -1) || (residencyStart >= 0 && (((unsigned int) (millis() - residencyStart)) < (TEMP_RESIDENCY_TIME * 1000UL))) ) { @@ -1089,9 +1120,9 @@ void process_commands() if( (millis() - codenum) > 1000UL ) { //Print Temp Reading and remaining time every 1 second while heating up/cooling down SERIAL_PROTOCOLPGM("T:"); - SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1); + SERIAL_PROTOCOL_F(degHotend(tmp_extruder),1); SERIAL_PROTOCOLPGM(" E:"); - SERIAL_PROTOCOL((int)tmp_extruder); + SERIAL_PROTOCOL((int)tmp_extruder); #ifdef TEMP_RESIDENCY_TIME SERIAL_PROTOCOLPGM(" W:"); if(residencyStart > -1) @@ -1099,7 +1130,7 @@ void process_commands() codenum = ((TEMP_RESIDENCY_TIME * 1000UL) - (millis() - residencyStart)) / 1000UL; SERIAL_PROTOCOLLN( codenum ); } - else + else { SERIAL_PROTOCOLLN( "?" ); } @@ -1116,7 +1147,7 @@ void process_commands() or when current temp falls outside the hysteresis after target temp was reached */ if ((residencyStart == -1 && target_direction && (degHotend(tmp_extruder) >= (degTargetHotend(tmp_extruder)-TEMP_WINDOW))) || (residencyStart == -1 && !target_direction && (degHotend(tmp_extruder) <= (degTargetHotend(tmp_extruder)+TEMP_WINDOW))) || - (residencyStart > -1 && labs(degHotend(tmp_extruder) - degTargetHotend(tmp_extruder)) > TEMP_HYSTERESIS) ) + (residencyStart > -1 && labs(degHotend(tmp_extruder) - degTargetHotend(tmp_extruder)) > TEMP_HYSTERESIS) ) { residencyStart = millis(); } @@ -1128,11 +1159,11 @@ void process_commands() } break; case 190: // M190 - Wait for bed heater to reach target. - #if TEMP_BED_PIN > -1 + #if defined(TEMP_BED_PIN) && TEMP_BED_PIN > -1 LCD_MESSAGEPGM(MSG_BED_HEATING); if (code_seen('S')) setTargetBed(code_value()); - codenum = millis(); - while(isHeatingBed()) + codenum = millis(); + while(isHeatingBed()) { if(( millis() - codenum) > 1000 ) //Print Temp Reading every 1 second while heating up. { @@ -1140,11 +1171,11 @@ void process_commands() SERIAL_PROTOCOLPGM("T:"); SERIAL_PROTOCOL(tt); SERIAL_PROTOCOLPGM(" E:"); - SERIAL_PROTOCOL((int)active_extruder); + SERIAL_PROTOCOL((int)active_extruder); SERIAL_PROTOCOLPGM(" B:"); - SERIAL_PROTOCOL_F(degBed(),1); - SERIAL_PROTOCOLLN(""); - codenum = millis(); + SERIAL_PROTOCOL_F(degBed(),1); + SERIAL_PROTOCOLLN(""); + codenum = millis(); } manage_heater(); manage_inactivity(); @@ -1155,38 +1186,69 @@ void process_commands() #endif break; - #if FAN_PIN > -1 + #if defined(FAN_PIN) && FAN_PIN > -1 case 106: //M106 Fan On if (code_seen('S')){ fanSpeed=constrain(code_value(),0,255); } else { - fanSpeed=255; + fanSpeed=255; } break; case 107: //M107 Fan Off fanSpeed = 0; break; #endif //FAN_PIN + #ifdef BARICUDA + // PWM for HEATER_1_PIN + #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1 + case 126: //M126 valve open + if (code_seen('S')){ + ValvePressure=constrain(code_value(),0,255); + } + else { + ValvePressure=255; + } + break; + case 127: //M127 valve closed + ValvePressure = 0; + break; + #endif //HEATER_1_PIN - #if (PS_ON_PIN > -1) + // PWM for HEATER_2_PIN + #if defined(HEATER_2_PIN) && HEATER_2_PIN > -1 + case 128: //M128 valve open + if (code_seen('S')){ + EtoPPressure=constrain(code_value(),0,255); + } + else { + EtoPPressure=255; + } + break; + case 129: //M129 valve closed + EtoPPressure = 0; + break; + #endif //HEATER_2_PIN + #endif + + #if defined(PS_ON_PIN) && PS_ON_PIN > -1 case 80: // M80 - ATX Power On SET_OUTPUT(PS_ON_PIN); //GND WRITE(PS_ON_PIN, PS_ON_AWAKE); break; #endif - + case 81: // M81 - ATX Power Off - - #if defined SUICIDE_PIN && SUICIDE_PIN > -1 + + #if defined(SUICIDE_PIN) && SUICIDE_PIN > -1 st_synchronize(); suicide(); - #elif (PS_ON_PIN > -1) - SET_OUTPUT(PS_ON_PIN); + #elif defined(PS_ON_PIN) && PS_ON_PIN > -1 + SET_OUTPUT(PS_ON_PIN); WRITE(PS_ON_PIN, PS_ON_ASLEEP); #endif - break; - + break; + case 82: axis_relative_modes[3] = false; break; @@ -1195,11 +1257,11 @@ void process_commands() break; case 18: //compatibility case 84: // M84 - if(code_seen('S')){ - stepper_inactive_time = code_value() * 1000; + if(code_seen('S')){ + stepper_inactive_time = code_value() * 1000; } else - { + { bool all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2]))|| (code_seen(axis_codes[3]))); if(all_axis) { @@ -1221,18 +1283,18 @@ void process_commands() disable_e1(); disable_e2(); } - #endif + #endif } } break; case 85: // M85 code_seen('S'); - max_inactive_time = code_value() * 1000; + max_inactive_time = code_value() * 1000; break; case 92: // M92 - for(int8_t i=0; i < NUM_AXIS; i++) + for(int8_t i=0; i < NUM_AXIS; i++) { - if(code_seen(axis_codes[i])) + if(code_seen(axis_codes[i])) { if(i == 3) { // E float value = code_value(); @@ -1266,16 +1328,16 @@ void process_commands() SERIAL_PROTOCOL(current_position[Y_AXIS]); SERIAL_PROTOCOLPGM("Z:"); SERIAL_PROTOCOL(current_position[Z_AXIS]); - SERIAL_PROTOCOLPGM("E:"); + SERIAL_PROTOCOLPGM("E:"); SERIAL_PROTOCOL(current_position[E_AXIS]); - + SERIAL_PROTOCOLPGM(MSG_COUNT_X); SERIAL_PROTOCOL(float(st_get_position(X_AXIS))/axis_steps_per_unit[X_AXIS]); SERIAL_PROTOCOLPGM("Y:"); SERIAL_PROTOCOL(float(st_get_position(Y_AXIS))/axis_steps_per_unit[Y_AXIS]); SERIAL_PROTOCOLPGM("Z:"); SERIAL_PROTOCOL(float(st_get_position(Z_AXIS))/axis_steps_per_unit[Z_AXIS]); - + SERIAL_PROTOCOLLN(""); break; case 120: // M120 @@ -1286,34 +1348,34 @@ void process_commands() break; case 119: // M119 SERIAL_PROTOCOLLN(MSG_M119_REPORT); - #if (X_MIN_PIN > -1) + #if defined(X_MIN_PIN) && X_MIN_PIN > -1 SERIAL_PROTOCOLPGM(MSG_X_MIN); SERIAL_PROTOCOLLN(((READ(X_MIN_PIN)^X_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); #endif - #if (X_MAX_PIN > -1) + #if defined(X_MAX_PIN) && X_MAX_PIN > -1 SERIAL_PROTOCOLPGM(MSG_X_MAX); SERIAL_PROTOCOLLN(((READ(X_MAX_PIN)^X_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); #endif - #if (Y_MIN_PIN > -1) + #if defined(Y_MIN_PIN) && Y_MIN_PIN > -1 SERIAL_PROTOCOLPGM(MSG_Y_MIN); SERIAL_PROTOCOLLN(((READ(Y_MIN_PIN)^Y_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); #endif - #if (Y_MAX_PIN > -1) + #if defined(Y_MAX_PIN) && Y_MAX_PIN > -1 SERIAL_PROTOCOLPGM(MSG_Y_MAX); SERIAL_PROTOCOLLN(((READ(Y_MAX_PIN)^Y_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); #endif - #if (Z_MIN_PIN > -1) + #if defined(Z_MIN_PIN) && Z_MIN_PIN > -1 SERIAL_PROTOCOLPGM(MSG_Z_MIN); SERIAL_PROTOCOLLN(((READ(Z_MIN_PIN)^Z_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); #endif - #if (Z_MAX_PIN > -1) + #if defined(Z_MAX_PIN) && Z_MAX_PIN > -1 SERIAL_PROTOCOLPGM(MSG_Z_MAX); SERIAL_PROTOCOLLN(((READ(Z_MAX_PIN)^Z_ENDSTOPS_INVERTING)?MSG_ENDSTOP_HIT:MSG_ENDSTOP_OPEN)); #endif break; //TODO: update for all axis, use for loop case 201: // M201 - for(int8_t i=0; i < NUM_AXIS; i++) + for(int8_t i=0; i < NUM_AXIS; i++) { if(code_seen(axis_codes[i])) { @@ -1321,7 +1383,7 @@ void process_commands() } } // steps per sq second need to be updated to agree with the units per sq second (as they are what is used in the planner) - reset_acceleration_rates(); + reset_acceleration_rates(); break; #if 0 // Not used for Sprinter/grbl gen6 case 202: // M202 @@ -1352,7 +1414,7 @@ void process_commands() } break; case 206: // M206 additional homeing offset - for(int8_t i=0; i < 3; i++) + for(int8_t i=0; i < 3; i++) { if(code_seen(axis_codes[i])) add_homeing[i] = code_value(); } @@ -1360,47 +1422,47 @@ void process_commands() #ifdef FWRETRACT case 207: //M207 - set retract length S[positive mm] F[feedrate mm/sec] Z[additional zlift/hop] { - if(code_seen('S')) + if(code_seen('S')) { retract_length = code_value() ; } - if(code_seen('F')) + if(code_seen('F')) { retract_feedrate = code_value() ; } - if(code_seen('Z')) + if(code_seen('Z')) { retract_zlift = code_value() ; } }break; case 208: // M208 - set retract recover length S[positive mm surplus to the M207 S*] F[feedrate mm/sec] { - if(code_seen('S')) + if(code_seen('S')) { retract_recover_length = code_value() ; } - if(code_seen('F')) + if(code_seen('F')) { retract_recover_feedrate = code_value() ; } }break; case 209: // M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction. { - if(code_seen('S')) + if(code_seen('S')) { int t= code_value() ; switch(t) { case 0: autoretract_enabled=false;retracted=false;break; case 1: autoretract_enabled=true;retracted=false;break; - default: + default: SERIAL_ECHO_START; SERIAL_ECHOPGM(MSG_UNKNOWN_COMMAND); SERIAL_ECHO(cmdbuffer[bufindr]); SERIAL_ECHOLNPGM("\""); } } - + }break; #endif // FWRETRACT #if EXTRUDERS > 1 @@ -1409,7 +1471,7 @@ void process_commands() if(setTargetedHotend(218)){ break; } - if(code_seen('X')) + if(code_seen('X')) { extruder_offset[X_AXIS][tmp_extruder] = code_value(); } @@ -1419,7 +1481,7 @@ void process_commands() } SERIAL_ECHO_START; SERIAL_ECHOPGM(MSG_HOTEND_OFFSET); - for(tmp_extruder = 0; tmp_extruder < EXTRUDERS; tmp_extruder++) + for(tmp_extruder = 0; tmp_extruder < EXTRUDERS; tmp_extruder++) { SERIAL_ECHO(" "); SERIAL_ECHO(extruder_offset[X_AXIS][tmp_extruder]); @@ -1431,7 +1493,7 @@ void process_commands() #endif case 220: // M220 S- set speed factor override percentage { - if(code_seen('S')) + if(code_seen('S')) { feedmultiply = code_value() ; } @@ -1439,23 +1501,58 @@ void process_commands() break; case 221: // M221 S- set extrude factor override percentage { - if(code_seen('S')) + if(code_seen('S')) { extrudemultiply = code_value() ; } } break; - #if defined(LARGE_FLASH) && LARGE_FLASH == true && defined(BEEPER) && BEEPER > -1 + #if NUM_SERVOS > 0 + case 280: // M280 - set servo position absolute. P: servo index, S: angle or microseconds + { + int servo_index = -1; + int servo_position = 0; + if (code_seen('P')) + servo_index = code_value(); + if (code_seen('S')) { + servo_position = code_value(); + if ((servo_index >= 0) && (servo_index < NUM_SERVOS)) { + servos[servo_index].write(servo_position); + } + else { + SERIAL_ECHO_START; + SERIAL_ECHO("Servo "); + SERIAL_ECHO(servo_index); + SERIAL_ECHOLN(" out of range"); + } + } + else if (servo_index >= 0) { + SERIAL_PROTOCOL(MSG_OK); + SERIAL_PROTOCOL(" Servo "); + SERIAL_PROTOCOL(servo_index); + SERIAL_PROTOCOL(": "); + SERIAL_PROTOCOL(servos[servo_index].read()); + SERIAL_PROTOCOLLN(""); + } + } + break; + #endif // NUM_SERVOS > 0 + + #if LARGE_FLASH == true && ( BEEPER > 0 || defined(ULTRALCD) ) case 300: // M300 { int beepS = code_seen('S') ? code_value() : 110; int beepP = code_seen('P') ? code_value() : 1000; if (beepS > 0) { - tone(BEEPER, beepS); - delay(beepP); - noTone(BEEPER); + #if BEEPER > 0 + tone(BEEPER, beepS); + delay(beepP); + noTone(BEEPER); + #elif defined(ULTRALCD) + lcd_buzz(beepS, beepP); + #endif } else { @@ -1475,10 +1572,10 @@ void process_commands() #ifdef PID_ADD_EXTRUSION_RATE if(code_seen('C')) Kc = code_value(); #endif - + updatePID(); SERIAL_PROTOCOL(MSG_OK); - SERIAL_PROTOCOL(" p:"); + SERIAL_PROTOCOL(" p:"); SERIAL_PROTOCOL(Kp); SERIAL_PROTOCOL(" i:"); SERIAL_PROTOCOL(unscalePID_i(Ki)); @@ -1502,7 +1599,7 @@ void process_commands() updatePID(); SERIAL_PROTOCOL(MSG_OK); - SERIAL_PROTOCOL(" p:"); + SERIAL_PROTOCOL(" p:"); SERIAL_PROTOCOL(bedKp); SERIAL_PROTOCOL(" i:"); SERIAL_PROTOCOL(unscalePID_i(bedKi)); @@ -1514,8 +1611,7 @@ void process_commands() #endif //PIDTEMP case 240: // M240 Triggers a camera by emulating a Canon RC-1 : http://www.doc-diy.net/photo/rc-1_hacked/ { - #ifdef PHOTOGRAPH_PIN - #if (PHOTOGRAPH_PIN > -1) + #if defined(PHOTOGRAPH_PIN) && PHOTOGRAPH_PIN > -1 const uint8_t NUM_PULSES=16; const float PULSE_LENGTH=0.01524; for(int i=0; i < NUM_PULSES; i++) { @@ -1531,24 +1627,26 @@ void process_commands() WRITE(PHOTOGRAPH_PIN, LOW); _delay_ms(PULSE_LENGTH); } - #endif #endif } break; - - case 302: // allow cold extrudes + #ifdef PREVENT_DANGEROUS_EXTRUDE + case 302: // allow cold extrudes, or set the minimum extrude temperature { - allow_cold_extrudes(true); + float temp = .0; + if (code_seen('S')) temp=code_value(); + set_extrude_min_temp(temp); } break; + #endif case 303: // M303 PID autotune { float temp = 150.0; int e=0; int c=5; if (code_seen('E')) e=code_value(); - if (e<0) - temp=70; + if (e<0) + temp=70; if (code_seen('S')) temp=code_value(); if (code_seen('C')) c=code_value(); PID_autotune(temp, e, c); @@ -1600,7 +1698,7 @@ void process_commands() lastpos[Z_AXIS]=current_position[Z_AXIS]; lastpos[E_AXIS]=current_position[E_AXIS]; //retract by E - if(code_seen('E')) + if(code_seen('E')) { target[E_AXIS]+= code_value(); } @@ -1611,9 +1709,9 @@ void process_commands() #endif } plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); - + //lift Z - if(code_seen('Z')) + if(code_seen('Z')) { target[Z_AXIS]+= code_value(); } @@ -1624,9 +1722,9 @@ void process_commands() #endif } plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); - + //move xy - if(code_seen('X')) + if(code_seen('X')) { target[X_AXIS]+= code_value(); } @@ -1636,7 +1734,7 @@ void process_commands() target[X_AXIS]= FILAMENTCHANGE_XPOS ; #endif } - if(code_seen('Y')) + if(code_seen('Y')) { target[Y_AXIS]= code_value(); } @@ -1646,9 +1744,9 @@ void process_commands() target[Y_AXIS]= FILAMENTCHANGE_YPOS ; #endif } - + plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); - + if(code_seen('L')) { target[E_AXIS]+= code_value(); @@ -1659,9 +1757,9 @@ void process_commands() target[E_AXIS]+= FILAMENTCHANGE_FINALRETRACT ; #endif } - + plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feedrate/60, active_extruder); - + //finish moves st_synchronize(); //disable extruder steppers so filament can be removed @@ -1671,27 +1769,28 @@ void process_commands() delay(100); LCD_ALERTMESSAGEPGM(MSG_FILAMENTCHANGE); uint8_t cnt=0; - while(!LCD_CLICKED){ + while(!lcd_clicked()){ cnt++; manage_heater(); manage_inactivity(); lcd_update(); - - #if BEEPER > -1 if(cnt==0) { + #if BEEPER > 0 SET_OUTPUT(BEEPER); - + WRITE(BEEPER,HIGH); delay(3); WRITE(BEEPER,LOW); delay(3); - } + #else + lcd_buzz(1000/6,100); #endif + } } - + //return to normal - if(code_seen('L')) + if(code_seen('L')) { target[E_AXIS]+= -code_value(); } @@ -1709,18 +1808,19 @@ void process_commands() plan_buffer_line(lastpos[X_AXIS], lastpos[Y_AXIS], lastpos[Z_AXIS], lastpos[E_AXIS], feedrate/60, active_extruder); //final untretract } break; - #endif //FILAMENTCHANGEENABLE + #endif //FILAMENTCHANGEENABLE case 907: // M907 Set digital trimpot motor current using axis codes. { - #if DIGIPOTSS_PIN > -1 - for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) digipot_current(i,code_value()); + #if defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1 + for(int i=0;i -1 + #if defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1 uint8_t channel,current; if(code_seen('P')) channel=code_value(); if(code_seen('S')) current=code_value(); @@ -1730,9 +1830,9 @@ void process_commands() break; case 350: // M350 Set microstepping mode. Warning: Steps per unit remains unchanged. S code sets stepping mode for all drivers. { - #if X_MS1_PIN > -1 - if(code_seen('S')) for(int i=0;i<=4;i++) microstep_mode(i,code_value()); - for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) microstep_mode(i,(uint8_t)code_value()); + #if defined(X_MS1_PIN) && X_MS1_PIN > -1 + if(code_seen('S')) for(int i=0;i<=4;i++) microstep_mode(i,code_value()); + for(int i=0;i -1 + #if defined(X_MS1_PIN) && X_MS1_PIN > -1 if(code_seen('S')) switch((int)code_value()) { case 1: - for(int i=0;i<=NUM_AXIS;i++) if(code_seen(axis_codes[i])) microstep_ms(i,code_value(),-1); + for(int i=0;i= EXTRUDERS) { @@ -1790,7 +1890,7 @@ void process_commands() // Offset extruder (only by XY) int i; for(i = 0; i < 2; i++) { - current_position[i] = current_position[i] - + current_position[i] = current_position[i] - extruder_offset[i][active_extruder] + extruder_offset[i][tmp_extruder]; } @@ -1836,14 +1936,14 @@ void ClearToSend() if(fromsd[bufindr]) return; #endif //SDSUPPORT - SERIAL_PROTOCOLLNPGM(MSG_OK); + SERIAL_PROTOCOLLNPGM(MSG_OK); } void get_coordinates() { bool seen[4]={false,false,false,false}; for(int8_t i=0; i < NUM_AXIS; i++) { - if(code_seen(axis_codes[i])) + if(code_seen(axis_codes[i])) { destination[i] = (float)code_value() + (axis_relative_modes[i] || relative_mode)*current_position[i]; seen[i]=true; @@ -1861,23 +1961,23 @@ void get_coordinates() float echange=destination[E_AXIS]-current_position[E_AXIS]; if(echange<-MIN_RETRACT) //retract { - if(!retracted) + if(!retracted) { - + destination[Z_AXIS]+=retract_zlift; //not sure why chaninging current_position negatively does not work. //if slicer retracted by echange=-1mm and you want to retract 3mm, corrrectede=-2mm additionally float correctede=-echange-retract_length; //to generate the additional steps, not the destination is changed, but inversely the current position - current_position[E_AXIS]+=-correctede; + current_position[E_AXIS]+=-correctede; feedrate=retract_feedrate; retracted=true; } - + } - else + else if(echange>MIN_RETRACT) //retract_recover { - if(retracted) + if(retracted) { //current_position[Z_AXIS]+=-retract_zlift; //if slicer retracted_recovered by echange=+1mm and you want to retract_recover 3mm, corrrectede=2mm additionally @@ -1887,7 +1987,7 @@ void get_coordinates() retracted=false; } } - + } #endif //FWRETRACT } @@ -1905,7 +2005,7 @@ void get_arc_coordinates() if(code_seen('I')) { offset[0] = code_value(); - } + } else { offset[0] = 0.0; } @@ -1936,7 +2036,7 @@ void prepare_move() { clamp_to_software_endstops(destination); - previous_millis_cmd = millis(); + previous_millis_cmd = millis(); // Do not use feedmultiply for E or Z only moves if( (current_position[X_AXIS] == destination [X_AXIS]) && (current_position[Y_AXIS] == destination [Y_AXIS])) { plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); @@ -1954,7 +2054,7 @@ void prepare_arc_move(char isclockwise) { // Trace the arc mc_arc(current_position, destination, offset, X_AXIS, Y_AXIS, Z_AXIS, feedrate*feedmultiply/60/100.0, r, isclockwise, active_extruder); - + // As far as the parser is concerned, the position is now == target. In reality the // motion control system might still be processing the action and the real tool position // in any intermediate location. @@ -1964,7 +2064,14 @@ void prepare_arc_move(char isclockwise) { previous_millis_cmd = millis(); } -#ifdef CONTROLLERFAN_PIN +#if defined(CONTROLLERFAN_PIN) && CONTROLLERFAN_PIN > -1 + +#if defined(FAN_PIN) + #if CONTROLLERFAN_PIN == FAN_PIN + #error "You cannot set CONTROLLERFAN_PIN equal to FAN_PIN" + #endif +#endif + unsigned long lastMotor = 0; //Save the time for when a motor was turned on last unsigned long lastMotorCheck = 0; @@ -1973,59 +2080,41 @@ void controllerFan() if ((millis() - lastMotorCheck) >= 2500) //Not a time critical function, so we only check every 2500ms { lastMotorCheck = millis(); - + if(!READ(X_ENABLE_PIN) || !READ(Y_ENABLE_PIN) || !READ(Z_ENABLE_PIN) #if EXTRUDERS > 2 || !READ(E2_ENABLE_PIN) #endif #if EXTRUDER > 1 - || !READ(E2_ENABLE_PIN) + || !READ(E1_ENABLE_PIN) #endif - || !READ(E0_ENABLE_PIN)) //If any of the drivers are enabled... + || !READ(E0_ENABLE_PIN)) //If any of the drivers are enabled... { lastMotor = millis(); //... set time to NOW so the fan will turn on } - if ((millis() - lastMotor) >= (CONTROLLERFAN_SEC*1000UL) || lastMotor == 0) //If the last time any driver was enabled, is longer since than CONTROLLERSEC... + if ((millis() - lastMotor) >= (CONTROLLERFAN_SECS*1000UL) || lastMotor == 0) //If the last time any driver was enabled, is longer since than CONTROLLERSEC... { - WRITE(CONTROLLERFAN_PIN, LOW); //... turn the fan off + digitalWrite(CONTROLLERFAN_PIN, 0); + analogWrite(CONTROLLERFAN_PIN, 0); } else { - WRITE(CONTROLLERFAN_PIN, HIGH); //... turn the fan on + // allows digital or PWM fan output to be used (see M42 handling) + digitalWrite(CONTROLLERFAN_PIN, CONTROLLERFAN_SPEED); + analogWrite(CONTROLLERFAN_PIN, CONTROLLERFAN_SPEED); } } } #endif -#ifdef EXTRUDERFAN_PIN -unsigned long lastExtruderCheck = 0; - -void extruderFan() +void manage_inactivity() { - if ((millis() - lastExtruderCheck) >= 2500) //Not a time critical function, so we only check every 2500ms - { - lastExtruderCheck = millis(); - - if (degHotend(active_extruder) < EXTRUDERFAN_DEC) - { - WRITE(EXTRUDERFAN_PIN, LOW); //... turn the fan off - } - else - { - WRITE(EXTRUDERFAN_PIN, HIGH); //... turn the fan on - } - } -} -#endif - -void manage_inactivity() -{ - if( (millis() - previous_millis_cmd) > max_inactive_time ) - if(max_inactive_time) - kill(); + if( (millis() - previous_millis_cmd) > max_inactive_time ) + if(max_inactive_time) + kill(); if(stepper_inactive_time) { - if( (millis() - previous_millis_cmd) > stepper_inactive_time ) + if( (millis() - previous_millis_cmd) > stepper_inactive_time ) { if(blocks_queued() == false) { disable_x(); @@ -2037,23 +2126,23 @@ void manage_inactivity() } } } - #if( KILL_PIN>-1 ) + #if defined(KILL_PIN) && KILL_PIN > -1 if( 0 == READ(KILL_PIN) ) kill(); #endif - #ifdef CONTROLLERFAN_PIN + #if defined(CONTROLLERFAN_PIN) && CONTROLLERFAN_PIN > -1 controllerFan(); //Check if fan should be turned on to cool stepper drivers down #endif #ifdef EXTRUDER_RUNOUT_PREVENT - if( (millis() - previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 ) + if( (millis() - previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 ) if(degHotend(active_extruder)>EXTRUDER_RUNOUT_MINTEMP) { bool oldstatus=READ(E0_ENABLE_PIN); enable_e0(); float oldepos=current_position[E_AXIS]; float oldedes=destination[E_AXIS]; - plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], - current_position[E_AXIS]+EXTRUDER_RUNOUT_EXTRUDE*EXTRUDER_RUNOUT_ESTEPS/axis_steps_per_unit[E_AXIS], + plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], + current_position[E_AXIS]+EXTRUDER_RUNOUT_EXTRUDE*EXTRUDER_RUNOUT_ESTEPS/axis_steps_per_unit[E_AXIS], EXTRUDER_RUNOUT_SPEED/60.*EXTRUDER_RUNOUT_ESTEPS/axis_steps_per_unit[E_AXIS], active_extruder); current_position[E_AXIS]=oldepos; destination[E_AXIS]=oldedes; @@ -2077,8 +2166,10 @@ void kill() disable_e0(); disable_e1(); disable_e2(); - - if(PS_ON_PIN > -1) pinMode(PS_ON_PIN,INPUT); + +#if defined(PS_ON_PIN) && PS_ON_PIN > -1 + pinMode(PS_ON_PIN,INPUT); +#endif SERIAL_ERROR_START; SERIAL_ERRORLNPGM(MSG_ERR_KILLED); LCD_ALERTMESSAGEPGM(MSG_KILLED); @@ -2106,7 +2197,7 @@ void setPwmFrequency(uint8_t pin, int val) val &= 0x07; switch(digitalPinToTimer(pin)) { - + #if defined(TCCR0A) case TIMER0A: case TIMER0B: @@ -2148,7 +2239,7 @@ void setPwmFrequency(uint8_t pin, int val) break; #endif - #if defined(TCCR4A) + #if defined(TCCR4A) case TIMER4A: case TIMER4B: case TIMER4C: @@ -2157,7 +2248,7 @@ void setPwmFrequency(uint8_t pin, int val) break; #endif - #if defined(TCCR5A) + #if defined(TCCR5A) case TIMER5A: case TIMER5B: case TIMER5C: @@ -2196,3 +2287,4 @@ bool setTargetedHotend(int code){ } return false; } + diff --git a/Marlin/Servo.cpp b/Marlin/Servo.cpp new file mode 100644 index 0000000000..1b42ce0b04 --- /dev/null +++ b/Marlin/Servo.cpp @@ -0,0 +1,339 @@ +/* + Servo.cpp - Interrupt driven Servo library for Arduino using 16 bit timers- Version 2 + Copyright (c) 2009 Michael Margolis. All right reserved. + + This library is free software; you can redistribute it and/or + modify it under the terms of the GNU Lesser General Public + License as published by the Free Software Foundation; either + version 2.1 of the License, or (at your option) any later version. + + This library is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + Lesser General Public License for more details. + + You should have received a copy of the GNU Lesser General Public + License along with this library; if not, write to the Free Software + Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +/* + + A servo is activated by creating an instance of the Servo class passing the desired pin to the attach() method. + The servos are pulsed in the background using the value most recently written using the write() method + + Note that analogWrite of PWM on pins associated with the timer are disabled when the first servo is attached. + Timers are seized as needed in groups of 12 servos - 24 servos use two timers, 48 servos will use four. + + The methods are: + + Servo - Class for manipulating servo motors connected to Arduino pins. + + attach(pin ) - Attaches a servo motor to an i/o pin. + attach(pin, min, max ) - Attaches to a pin setting min and max values in microseconds + default min is 544, max is 2400 + + write() - Sets the servo angle in degrees. (invalid angle that is valid as pulse in microseconds is treated as microseconds) + writeMicroseconds() - Sets the servo pulse width in microseconds + read() - Gets the last written servo pulse width as an angle between 0 and 180. + readMicroseconds() - Gets the last written servo pulse width in microseconds. (was read_us() in first release) + attached() - Returns true if there is a servo attached. + detach() - Stops an attached servos from pulsing its i/o pin. + +*/ +#ifdef NUM_SERVOS +#include +#include + +#include "Servo.h" + +#define usToTicks(_us) (( clockCyclesPerMicrosecond()* _us) / 8) // converts microseconds to tick (assumes prescale of 8) // 12 Aug 2009 +#define ticksToUs(_ticks) (( (unsigned)_ticks * 8)/ clockCyclesPerMicrosecond() ) // converts from ticks back to microseconds + + +#define TRIM_DURATION 2 // compensation ticks to trim adjust for digitalWrite delays // 12 August 2009 + +//#define NBR_TIMERS (MAX_SERVOS / SERVOS_PER_TIMER) + +static servo_t servos[MAX_SERVOS]; // static array of servo structures +static volatile int8_t Channel[_Nbr_16timers ]; // counter for the servo being pulsed for each timer (or -1 if refresh interval) + +uint8_t ServoCount = 0; // the total number of attached servos + + +// convenience macros +#define SERVO_INDEX_TO_TIMER(_servo_nbr) ((timer16_Sequence_t)(_servo_nbr / SERVOS_PER_TIMER)) // returns the timer controlling this servo +#define SERVO_INDEX_TO_CHANNEL(_servo_nbr) (_servo_nbr % SERVOS_PER_TIMER) // returns the index of the servo on this timer +#define SERVO_INDEX(_timer,_channel) ((_timer*SERVOS_PER_TIMER) + _channel) // macro to access servo index by timer and channel +#define SERVO(_timer,_channel) (servos[SERVO_INDEX(_timer,_channel)]) // macro to access servo class by timer and channel + +#define SERVO_MIN() (MIN_PULSE_WIDTH - this->min * 4) // minimum value in uS for this servo +#define SERVO_MAX() (MAX_PULSE_WIDTH - this->max * 4) // maximum value in uS for this servo + +/************ static functions common to all instances ***********************/ + +static inline void handle_interrupts(timer16_Sequence_t timer, volatile uint16_t *TCNTn, volatile uint16_t* OCRnA) +{ + if( Channel[timer] < 0 ) + *TCNTn = 0; // channel set to -1 indicated that refresh interval completed so reset the timer + else{ + if( SERVO_INDEX(timer,Channel[timer]) < ServoCount && SERVO(timer,Channel[timer]).Pin.isActive == true ) + digitalWrite( SERVO(timer,Channel[timer]).Pin.nbr,LOW); // pulse this channel low if activated + } + + Channel[timer]++; // increment to the next channel + if( SERVO_INDEX(timer,Channel[timer]) < ServoCount && Channel[timer] < SERVOS_PER_TIMER) { + *OCRnA = *TCNTn + SERVO(timer,Channel[timer]).ticks; + if(SERVO(timer,Channel[timer]).Pin.isActive == true) // check if activated + digitalWrite( SERVO(timer,Channel[timer]).Pin.nbr,HIGH); // its an active channel so pulse it high + } + else { + // finished all channels so wait for the refresh period to expire before starting over + if( ((unsigned)*TCNTn) + 4 < usToTicks(REFRESH_INTERVAL) ) // allow a few ticks to ensure the next OCR1A not missed + *OCRnA = (unsigned int)usToTicks(REFRESH_INTERVAL); + else + *OCRnA = *TCNTn + 4; // at least REFRESH_INTERVAL has elapsed + Channel[timer] = -1; // this will get incremented at the end of the refresh period to start again at the first channel + } +} + +#ifndef WIRING // Wiring pre-defines signal handlers so don't define any if compiling for the Wiring platform +// Interrupt handlers for Arduino +#if defined(_useTimer1) +SIGNAL (TIMER1_COMPA_vect) +{ + handle_interrupts(_timer1, &TCNT1, &OCR1A); +} +#endif + +#if defined(_useTimer3) +SIGNAL (TIMER3_COMPA_vect) +{ + handle_interrupts(_timer3, &TCNT3, &OCR3A); +} +#endif + +#if defined(_useTimer4) +SIGNAL (TIMER4_COMPA_vect) +{ + handle_interrupts(_timer4, &TCNT4, &OCR4A); +} +#endif + +#if defined(_useTimer5) +SIGNAL (TIMER5_COMPA_vect) +{ + handle_interrupts(_timer5, &TCNT5, &OCR5A); +} +#endif + +#elif defined WIRING +// Interrupt handlers for Wiring +#if defined(_useTimer1) +void Timer1Service() +{ + handle_interrupts(_timer1, &TCNT1, &OCR1A); +} +#endif +#if defined(_useTimer3) +void Timer3Service() +{ + handle_interrupts(_timer3, &TCNT3, &OCR3A); +} +#endif +#endif + + +static void initISR(timer16_Sequence_t timer) +{ +#if defined (_useTimer1) + if(timer == _timer1) { + TCCR1A = 0; // normal counting mode + TCCR1B = _BV(CS11); // set prescaler of 8 + TCNT1 = 0; // clear the timer count +#if defined(__AVR_ATmega8__)|| defined(__AVR_ATmega128__) + TIFR |= _BV(OCF1A); // clear any pending interrupts; + TIMSK |= _BV(OCIE1A) ; // enable the output compare interrupt +#else + // here if not ATmega8 or ATmega128 + TIFR1 |= _BV(OCF1A); // clear any pending interrupts; + TIMSK1 |= _BV(OCIE1A) ; // enable the output compare interrupt +#endif +#if defined(WIRING) + timerAttach(TIMER1OUTCOMPAREA_INT, Timer1Service); +#endif + } +#endif + +#if defined (_useTimer3) + if(timer == _timer3) { + TCCR3A = 0; // normal counting mode + TCCR3B = _BV(CS31); // set prescaler of 8 + TCNT3 = 0; // clear the timer count +#if defined(__AVR_ATmega128__) + TIFR |= _BV(OCF3A); // clear any pending interrupts; + ETIMSK |= _BV(OCIE3A); // enable the output compare interrupt +#else + TIFR3 = _BV(OCF3A); // clear any pending interrupts; + TIMSK3 = _BV(OCIE3A) ; // enable the output compare interrupt +#endif +#if defined(WIRING) + timerAttach(TIMER3OUTCOMPAREA_INT, Timer3Service); // for Wiring platform only +#endif + } +#endif + +#if defined (_useTimer4) + if(timer == _timer4) { + TCCR4A = 0; // normal counting mode + TCCR4B = _BV(CS41); // set prescaler of 8 + TCNT4 = 0; // clear the timer count + TIFR4 = _BV(OCF4A); // clear any pending interrupts; + TIMSK4 = _BV(OCIE4A) ; // enable the output compare interrupt + } +#endif + +#if defined (_useTimer5) + if(timer == _timer5) { + TCCR5A = 0; // normal counting mode + TCCR5B = _BV(CS51); // set prescaler of 8 + TCNT5 = 0; // clear the timer count + TIFR5 = _BV(OCF5A); // clear any pending interrupts; + TIMSK5 = _BV(OCIE5A) ; // enable the output compare interrupt + } +#endif +} + +static void finISR(timer16_Sequence_t timer) +{ + //disable use of the given timer +#if defined WIRING // Wiring + if(timer == _timer1) { + #if defined(__AVR_ATmega1281__)||defined(__AVR_ATmega2561__) + TIMSK1 &= ~_BV(OCIE1A) ; // disable timer 1 output compare interrupt + #else + TIMSK &= ~_BV(OCIE1A) ; // disable timer 1 output compare interrupt + #endif + timerDetach(TIMER1OUTCOMPAREA_INT); + } + else if(timer == _timer3) { + #if defined(__AVR_ATmega1281__)||defined(__AVR_ATmega2561__) + TIMSK3 &= ~_BV(OCIE3A); // disable the timer3 output compare A interrupt + #else + ETIMSK &= ~_BV(OCIE3A); // disable the timer3 output compare A interrupt + #endif + timerDetach(TIMER3OUTCOMPAREA_INT); + } +#else + //For arduino - in future: call here to a currently undefined function to reset the timer +#endif +} + +static boolean isTimerActive(timer16_Sequence_t timer) +{ + // returns true if any servo is active on this timer + for(uint8_t channel=0; channel < SERVOS_PER_TIMER; channel++) { + if(SERVO(timer,channel).Pin.isActive == true) + return true; + } + return false; +} + + +/****************** end of static functions ******************************/ + +Servo::Servo() +{ + if( ServoCount < MAX_SERVOS) { + this->servoIndex = ServoCount++; // assign a servo index to this instance + servos[this->servoIndex].ticks = usToTicks(DEFAULT_PULSE_WIDTH); // store default values - 12 Aug 2009 + } + else + this->servoIndex = INVALID_SERVO ; // too many servos +} + +uint8_t Servo::attach(int pin) +{ + return this->attach(pin, MIN_PULSE_WIDTH, MAX_PULSE_WIDTH); +} + +uint8_t Servo::attach(int pin, int min, int max) +{ + if(this->servoIndex < MAX_SERVOS ) { + pinMode( pin, OUTPUT) ; // set servo pin to output + servos[this->servoIndex].Pin.nbr = pin; + // todo min/max check: abs(min - MIN_PULSE_WIDTH) /4 < 128 + this->min = (MIN_PULSE_WIDTH - min)/4; //resolution of min/max is 4 uS + this->max = (MAX_PULSE_WIDTH - max)/4; + // initialize the timer if it has not already been initialized + timer16_Sequence_t timer = SERVO_INDEX_TO_TIMER(servoIndex); + if(isTimerActive(timer) == false) + initISR(timer); + servos[this->servoIndex].Pin.isActive = true; // this must be set after the check for isTimerActive + } + return this->servoIndex ; +} + +void Servo::detach() +{ + servos[this->servoIndex].Pin.isActive = false; + timer16_Sequence_t timer = SERVO_INDEX_TO_TIMER(servoIndex); + if(isTimerActive(timer) == false) { + finISR(timer); + } +} + +void Servo::write(int value) +{ + if(value < MIN_PULSE_WIDTH) + { // treat values less than 544 as angles in degrees (valid values in microseconds are handled as microseconds) + if(value < 0) value = 0; + if(value > 180) value = 180; + value = map(value, 0, 180, SERVO_MIN(), SERVO_MAX()); + } + this->writeMicroseconds(value); +} + +void Servo::writeMicroseconds(int value) +{ + // calculate and store the values for the given channel + byte channel = this->servoIndex; + if( (channel < MAX_SERVOS) ) // ensure channel is valid + { + if( value < SERVO_MIN() ) // ensure pulse width is valid + value = SERVO_MIN(); + else if( value > SERVO_MAX() ) + value = SERVO_MAX(); + + value = value - TRIM_DURATION; + value = usToTicks(value); // convert to ticks after compensating for interrupt overhead - 12 Aug 2009 + + uint8_t oldSREG = SREG; + cli(); + servos[channel].ticks = value; + SREG = oldSREG; + } +} + +int Servo::read() // return the value as degrees +{ + return map( this->readMicroseconds()+1, SERVO_MIN(), SERVO_MAX(), 0, 180); +} + +int Servo::readMicroseconds() +{ + unsigned int pulsewidth; + if( this->servoIndex != INVALID_SERVO ) + pulsewidth = ticksToUs(servos[this->servoIndex].ticks) + TRIM_DURATION ; // 12 aug 2009 + else + pulsewidth = 0; + + return pulsewidth; +} + +bool Servo::attached() +{ + return servos[this->servoIndex].Pin.isActive ; +} + +#endif diff --git a/Marlin/Servo.h b/Marlin/Servo.h new file mode 100644 index 0000000000..17c99f7974 --- /dev/null +++ b/Marlin/Servo.h @@ -0,0 +1,132 @@ +/* + Servo.h - Interrupt driven Servo library for Arduino using 16 bit timers- Version 2 + Copyright (c) 2009 Michael Margolis. All right reserved. + + This library is free software; you can redistribute it and/or + modify it under the terms of the GNU Lesser General Public + License as published by the Free Software Foundation; either + version 2.1 of the License, or (at your option) any later version. + + This library is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + Lesser General Public License for more details. + + You should have received a copy of the GNU Lesser General Public + License along with this library; if not, write to the Free Software + Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +*/ + +/* + + A servo is activated by creating an instance of the Servo class passing the desired pin to the attach() method. + The servos are pulsed in the background using the value most recently written using the write() method + + Note that analogWrite of PWM on pins associated with the timer are disabled when the first servo is attached. + Timers are seized as needed in groups of 12 servos - 24 servos use two timers, 48 servos will use four. + The sequence used to sieze timers is defined in timers.h + + The methods are: + + Servo - Class for manipulating servo motors connected to Arduino pins. + + attach(pin ) - Attaches a servo motor to an i/o pin. + attach(pin, min, max ) - Attaches to a pin setting min and max values in microseconds + default min is 544, max is 2400 + + write() - Sets the servo angle in degrees. (invalid angle that is valid as pulse in microseconds is treated as microseconds) + writeMicroseconds() - Sets the servo pulse width in microseconds + read() - Gets the last written servo pulse width as an angle between 0 and 180. + readMicroseconds() - Gets the last written servo pulse width in microseconds. (was read_us() in first release) + attached() - Returns true if there is a servo attached. + detach() - Stops an attached servos from pulsing its i/o pin. + */ + +#ifndef Servo_h +#define Servo_h + +#include + +/* + * Defines for 16 bit timers used with Servo library + * + * If _useTimerX is defined then TimerX is a 16 bit timer on the curent board + * timer16_Sequence_t enumerates the sequence that the timers should be allocated + * _Nbr_16timers indicates how many 16 bit timers are available. + * + */ + +// Say which 16 bit timers can be used and in what order +#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__) +#define _useTimer5 +//#define _useTimer1 +#define _useTimer3 +#define _useTimer4 +//typedef enum { _timer5, _timer1, _timer3, _timer4, _Nbr_16timers } timer16_Sequence_t ; +typedef enum { _timer5, _timer3, _timer4, _Nbr_16timers } timer16_Sequence_t ; + +#elif defined(__AVR_ATmega32U4__) +//#define _useTimer1 +#define _useTimer3 +//typedef enum { _timer1, _Nbr_16timers } timer16_Sequence_t ; +typedef enum { _timer3, _Nbr_16timers } timer16_Sequence_t ; + +#elif defined(__AVR_AT90USB646__) || defined(__AVR_AT90USB1286__) +#define _useTimer3 +//#define _useTimer1 +//typedef enum { _timer3, _timer1, _Nbr_16timers } timer16_Sequence_t ; +typedef enum { _timer3, _Nbr_16timers } timer16_Sequence_t ; + +#elif defined(__AVR_ATmega128__) ||defined(__AVR_ATmega1281__)||defined(__AVR_ATmega2561__) +#define _useTimer3 +//#define _useTimer1 +//typedef enum { _timer3, _timer1, _Nbr_16timers } timer16_Sequence_t ; +typedef enum { _timer3, _Nbr_16timers } timer16_Sequence_t ; + +#else // everything else +//#define _useTimer1 +//typedef enum { _timer1, _Nbr_16timers } timer16_Sequence_t ; +typedef enum { _Nbr_16timers } timer16_Sequence_t ; +#endif + +#define Servo_VERSION 2 // software version of this library + +#define MIN_PULSE_WIDTH 544 // the shortest pulse sent to a servo +#define MAX_PULSE_WIDTH 2400 // the longest pulse sent to a servo +#define DEFAULT_PULSE_WIDTH 1500 // default pulse width when servo is attached +#define REFRESH_INTERVAL 20000 // minumim time to refresh servos in microseconds + +#define SERVOS_PER_TIMER 12 // the maximum number of servos controlled by one timer +#define MAX_SERVOS (_Nbr_16timers * SERVOS_PER_TIMER) + +#define INVALID_SERVO 255 // flag indicating an invalid servo index + +typedef struct { + uint8_t nbr :6 ; // a pin number from 0 to 63 + uint8_t isActive :1 ; // true if this channel is enabled, pin not pulsed if false +} ServoPin_t ; + +typedef struct { + ServoPin_t Pin; + unsigned int ticks; +} servo_t; + +class Servo +{ +public: + Servo(); + uint8_t attach(int pin); // attach the given pin to the next free channel, sets pinMode, returns channel number or 0 if failure + uint8_t attach(int pin, int min, int max); // as above but also sets min and max values for writes. + void detach(); + void write(int value); // if value is < 200 its treated as an angle, otherwise as pulse width in microseconds + void writeMicroseconds(int value); // Write pulse width in microseconds + int read(); // returns current pulse width as an angle between 0 and 180 degrees + int readMicroseconds(); // returns current pulse width in microseconds for this servo (was read_us() in first release) + bool attached(); // return true if this servo is attached, otherwise false +private: + uint8_t servoIndex; // index into the channel data for this servo + int8_t min; // minimum is this value times 4 added to MIN_PULSE_WIDTH + int8_t max; // maximum is this value times 4 added to MAX_PULSE_WIDTH +}; + +#endif diff --git a/Marlin/dogm_lcd_implementation.h b/Marlin/dogm_lcd_implementation.h index c5192e7c5a..17a56adba7 100644 --- a/Marlin/dogm_lcd_implementation.h +++ b/Marlin/dogm_lcd_implementation.h @@ -19,12 +19,25 @@ * Implementation of the LCD display routines for a DOGM128 graphic display. These are common LCD 128x64 pixel graphic displays. **/ +#ifdef ULTIPANEL +#define BLEN_A 0 +#define BLEN_B 1 +#define BLEN_C 2 +#define EN_A (1< // DE_U8glib +#include #include "DOGMbitmaps.h" #include "dogm_font_data_marlin.h" #include "ultralcd.h" +#include "ultralcd_st7920_u8glib_rrd.h" /* Russian language not supported yet, needs custom font @@ -61,11 +74,10 @@ #define FONT_STATUSMENU u8g_font_6x9 - // LCD selection #ifdef U8GLIB_ST7920 -// SPI Com: SCK = en = (D4), MOSI = rw = (RS), CS = di = (ENABLE) -U8GLIB_ST7920_128X64_1X u8g(LCD_PINS_D4, LCD_PINS_ENABLE, LCD_PINS_RS); +//U8GLIB_ST7920_128X64_RRD u8g(0,0,0); +U8GLIB_ST7920_128X64_RRD u8g(0); #else U8GLIB_DOGM128 u8g(DOGLCD_CS, DOGLCD_A0); // HW-SPI Com: CS, A0 #endif @@ -88,11 +100,11 @@ static void lcd_implementation_init() u8g.setRot90(); // Rotate screen by 90° #endif -#ifdef LCD_SCREEN_ROT_180; +#ifdef LCD_SCREEN_ROT_180 u8g.setRot180(); // Rotate screen by 180° #endif -#ifdef LCD_SCREEN_ROT_270; +#ifdef LCD_SCREEN_ROT_270 u8g.setRot270(); // Rotate screen by 270° #endif @@ -266,7 +278,7 @@ static void lcd_implementation_status_screen() // Fan u8g.setFont(FONT_STATUSMENU); u8g.setPrintPos(104,27); - #if FAN_PIN > 0 + #if defined(FAN_PIN) && FAN_PIN > -1 u8g.print(itostr3(int((fanSpeed*100)/256 + 1))); u8g.print("%"); #else diff --git a/Marlin/fastio.h b/Marlin/fastio.h index ed77b50e23..0746bf12b9 100644 --- a/Marlin/fastio.h +++ b/Marlin/fastio.h @@ -2575,8 +2575,702 @@ pins #define PF7_DDR DDRF #endif + +#if defined (__AVR_ATmega1281__) || defined (__AVR_ATmega2561__) +// UART +#define RXD DIO0 +#define TXD DIO1 + +// SPI +#define SCK DIO10 +#define MISO DIO12 +#define MOSI DIO11 +#define SS DIO16 + +// TWI (I2C) +#define SCL DIO17 +#define SDA DIO18 + +// timers and PWM +#define OC0A DIO9 +#define OC0B DIO4 +#define OC1A DIO7 +#define OC1B DIO8 +#define OC2A DIO6 +#define OC3A DIO5 +#define OC3B DIO2 +#define OC3C DIO3 + + +// change for your board +#define DEBUG_LED DIO46 + +/* +pins +*/ +#define DIO0_PIN PINE0 +#define DIO0_RPORT PINE +#define DIO0_WPORT PORTE +#define DIO0_DDR DDRE +#define DIO0_PWM NULL + +#define DIO1_PIN PINE1 +#define DIO1_RPORT PINE +#define DIO1_WPORT PORTE +#define DIO1_DDR DDRE +#define DIO1_PWM NULL + +#define DIO2_PIN PINE4 +#define DIO2_RPORT PINE +#define DIO2_WPORT PORTE +#define DIO2_DDR DDRE +#define DIO2_PWM &OCR3BL + +#define DIO3_PIN PINE5 +#define DIO3_RPORT PINE +#define DIO3_WPORT PORTE +#define DIO3_DDR DDRE +#define DIO3_PWM &OCR3CL + +#define DIO4_PIN PING5 +#define DIO4_RPORT PING +#define DIO4_WPORT PORTG +#define DIO4_DDR DDRG +#define DIO4_PWM &OCR0B + +#define DIO5_PIN PINE3 +#define DIO5_RPORT PINE +#define DIO5_WPORT PORTE +#define DIO5_DDR DDRE +#define DIO5_PWM &OCR3AL + +#define DIO6_PIN PINB4 +#define DIO6_RPORT PINB +#define DIO6_WPORT PORTB +#define DIO6_DDR DDRB +#define DIO6_PWM &OCR2AL + +#define DIO7_PIN PINB5 +#define DIO7_RPORT PINB +#define DIO7_WPORT PORTB +#define DIO7_DDR DDRB +#define DIO7_PWM &OCR1AL + +#define DIO8_PIN PINB6 +#define DIO8_RPORT PINB +#define DIO8_WPORT PORTB +#define DIO8_DDR DDRB +#define DIO8_PWM &OCR1BL + +#define DIO9_PIN PINB7 +#define DIO9_RPORT PINB +#define DIO9_WPORT PORTB +#define DIO9_DDR DDRB +#define DIO9_PWM &OCR0AL + +#define DIO10_PIN PINB1 +#define DIO10_RPORT PINB +#define DIO10_WPORT PORTB +#define DIO10_DDR DDRB +#define DIO10_PWM NULL + +#define DIO11_PIN PINB2 +#define DIO11_RPORT PINB +#define DIO11_WPORT PORTB +#define DIO11_DDR DDRB +#define DIO11_PWM NULL + +#define DIO12_PIN PINB3 +#define DIO12_RPORT PINB +#define DIO12_WPORT PORTB +#define DIO12_DDR DDRB +#define DIO12_PWM NULL + +#define DIO13_PIN PINE2 +#define DIO13_RPORT PINE +#define DIO13_WPORT PORTE +#define DIO13_DDR DDRE +#define DIO13_PWM NULL + +#define DIO14_PIN PINE6 +#define DIO14_RPORT PINE +#define DIO14_WPORT PORTE +#define DIO14_DDR DDRE +#define DIO14_PWM NULL + +#define DIO15_PIN PINE7 +#define DIO15_RPORT PINE +#define DIO15_WPORT PORTE +#define DIO15_DDR DDRE +#define DIO15_PWM NULL + +#define DIO16_PIN PINB0 +#define DIO16_RPORT PINB +#define DIO16_WPORT PORTB +#define DIO16_DDR DDRB +#define DIO16_PWM NULL + +#define DIO17_PIN PIND0 +#define DIO17_RPORT PIND +#define DIO17_WPORT PORTD +#define DIO17_DDR DDRD +#define DIO17_PWM NULL + +#define DIO18_PIN PIND1 +#define DIO18_RPORT PIND +#define DIO18_WPORT PORTD +#define DIO18_DDR DDRD +#define DIO18_PWM NULL + +#define DIO19_PIN PIND2 +#define DIO19_RPORT PIND +#define DIO19_WPORT PORTD +#define DIO19_DDR DDRD +#define DIO19_PWM NULL + +#define DIO20_PIN PIND3 +#define DIO20_RPORT PIND +#define DIO20_WPORT PORTD +#define DIO20_DDR DDRD +#define DIO20_PWM NULL + +#define DIO21_PIN PIND4 +#define DIO21_RPORT PIND +#define DIO21_WPORT PORTD +#define DIO21_DDR DDRD +#define DIO21_PWM NULL + +#define DIO22_PIN PIND5 +#define DIO22_RPORT PIND +#define DIO22_WPORT PORTD +#define DIO22_DDR DDRD +#define DIO22_PWM NULL + +#define DIO23_PIN PIND6 +#define DIO23_RPORT PIND +#define DIO23_WPORT PORTD +#define DIO23_DDR DDRD +#define DIO23_PWM NULL + +#define DIO24_PIN PIND7 +#define DIO24_RPORT PIND +#define DIO24_WPORT PORTD +#define DIO24_DDR DDRD +#define DIO24_PWM NULL + +#define DIO25_PIN PING0 +#define DIO25_RPORT PING +#define DIO25_WPORT PORTG +#define DIO25_DDR DDRG +#define DIO25_PWM NULL + +#define DIO26_PIN PING1 +#define DIO26_RPORT PING +#define DIO26_WPORT PORTG +#define DIO26_DDR DDRG +#define DIO26_PWM NULL + +#define DIO27_PIN PING2 +#define DIO27_RPORT PING +#define DIO27_WPORT PORTG +#define DIO27_DDR DDRG +#define DIO27_PWM NULL + +#define DIO28_PIN PING3 +#define DIO28_RPORT PING +#define DIO28_WPORT PORTG +#define DIO28_DDR DDRG +#define DIO28_PWM NULL + +#define DIO29_PIN PING4 +#define DIO29_RPORT PING +#define DIO29_WPORT PORTG +#define DIO29_DDR DDRG +#define DIO29_PWM NULL + +#define DIO30_PIN PINC0 +#define DIO30_RPORT PINC +#define DIO30_WPORT PORTC +#define DIO30_DDR DDRC +#define DIO30_PWM NULL + +#define DIO31_PIN PINC1 +#define DIO31_RPORT PINC +#define DIO31_WPORT PORTC +#define DIO31_DDR DDRC +#define DIO31_PWM NULL + +#define DIO32_PIN PINC2 +#define DIO32_RPORT PINC +#define DIO32_WPORT PORTC +#define DIO32_DDR DDRC +#define DIO32_PWM NULL + +#define DIO33_PIN PINC3 +#define DIO33_RPORT PINC +#define DIO33_WPORT PORTC +#define DIO33_DDR DDRC +#define DIO33_PWM NULL + +#define DIO34_PIN PINC4 +#define DIO34_RPORT PINC +#define DIO34_WPORT PORTC +#define DIO34_DDR DDRC +#define DIO34_PWM NULL + +#define DIO35_PIN PINC5 +#define DIO35_RPORT PINC +#define DIO35_WPORT PORTC +#define DIO35_DDR DDRC +#define DIO35_PWM NULL + +#define DIO36_PIN PINC6 +#define DIO36_RPORT PINC +#define DIO36_WPORT PORTC +#define DIO36_DDR DDRC +#define DIO36_PWM NULL + +#define DIO37_PIN PINC7 +#define DIO37_RPORT PINC +#define DIO37_WPORT PORTC +#define DIO37_DDR DDRC +#define DIO37_PWM NULL + +#define DIO38_PIN PINA0 +#define DIO38_RPORT PINA +#define DIO38_WPORT PORTA +#define DIO38_DDR DDRA +#define DIO38_PWM NULL + +#define DIO39_PIN PINA1 +#define DIO39_RPORT PINA +#define DIO39_WPORT PORTA +#define DIO39_DDR DDRA +#define DIO39_PWM NULL + +#define DIO40_PIN PINA2 +#define DIO40_RPORT PINA +#define DIO40_WPORT PORTA +#define DIO40_DDR DDRA +#define DIO40_PWM NULL + +#define DIO41_PIN PINA3 +#define DIO41_RPORT PINA +#define DIO41_WPORT PORTA +#define DIO41_DDR DDRA +#define DIO41_PWM NULL + +#define DIO42_PIN PINA4 +#define DIO42_RPORT PINA +#define DIO42_WPORT PORTA +#define DIO42_DDR DDRA +#define DIO42_PWM NULL + +#define DIO43_PIN PINA5 +#define DIO43_RPORT PINA +#define DIO43_WPORT PORTA +#define DIO43_DDR DDRA +#define DIO43_PWM NULL + +#define DIO44_PIN PINA6 +#define DIO44_RPORT PINA +#define DIO44_WPORT PORTA +#define DIO44_DDR DDRA +#define DIO44_PWM NULL + +#define DIO45_PIN PINA7 +#define DIO45_RPORT PINA +#define DIO45_WPORT PORTA +#define DIO45_DDR DDRA +#define DIO45_PWM NULL + +#define DIO46_PIN PINF0 +#define DIO46_RPORT PINF +#define DIO46_WPORT PORTF +#define DIO46_DDR DDRF +#define DIO46_PWM NULL + +#define DIO47_PIN PINF1 +#define DIO47_RPORT PINF +#define DIO47_WPORT PORTF +#define DIO47_DDR DDRF +#define DIO47_PWM NULL + +#define DIO48_PIN PINF2 +#define DIO48_RPORT PINF +#define DIO48_WPORT PORTF +#define DIO48_DDR DDRF +#define DIO48_PWM NULL + +#define DIO49_PIN PINF3 +#define DIO49_RPORT PINF +#define DIO49_WPORT PORTF +#define DIO49_DDR DDRF +#define DIO49_PWM NULL + +#define DIO50_PIN PINF4 +#define DIO50_RPORT PINF +#define DIO50_WPORT PORTF +#define DIO50_DDR DDRF +#define DIO50_PWM NULL + +#define DIO51_PIN PINF5 +#define DIO51_RPORT PINF +#define DIO51_WPORT PORTF +#define DIO51_DDR DDRF +#define DIO51_PWM NULL + +#define DIO52_PIN PINF6 +#define DIO52_RPORT PINF +#define DIO52_WPORT PORTF +#define DIO52_DDR DDRF +#define DIO52_PWM NULL + +#define DIO53_PIN PINF7 +#define DIO53_RPORT PINF +#define DIO53_WPORT PORTF +#define DIO53_DDR DDRF +#define DIO53_PWM NULL + + + + +#undef PA0 +#define PA0_PIN PINA0 +#define PA0_RPORT PINA +#define PA0_WPORT PORTA +#define PA0_DDR DDRA +#define PA0_PWM NULL +#undef PA1 +#define PA1_PIN PINA1 +#define PA1_RPORT PINA +#define PA1_WPORT PORTA +#define PA1_DDR DDRA +#define PA1_PWM NULL +#undef PA2 +#define PA2_PIN PINA2 +#define PA2_RPORT PINA +#define PA2_WPORT PORTA +#define PA2_DDR DDRA +#define PA2_PWM NULL +#undef PA3 +#define PA3_PIN PINA3 +#define PA3_RPORT PINA +#define PA3_WPORT PORTA +#define PA3_DDR DDRA +#define PA3_PWM NULL +#undef PA4 +#define PA4_PIN PINA4 +#define PA4_RPORT PINA +#define PA4_WPORT PORTA +#define PA4_DDR DDRA +#define PA4_PWM NULL +#undef PA5 +#define PA5_PIN PINA5 +#define PA5_RPORT PINA +#define PA5_WPORT PORTA +#define PA5_DDR DDRA +#define PA5_PWM NULL +#undef PA6 +#define PA6_PIN PINA6 +#define PA6_RPORT PINA +#define PA6_WPORT PORTA +#define PA6_DDR DDRA +#define PA6_PWM NULL +#undef PA7 +#define PA7_PIN PINA7 +#define PA7_RPORT PINA +#define PA7_WPORT PORTA +#define PA7_DDR DDRA +#define PA7_PWM NULL + +#undef PB0 +#define PB0_PIN PINB0 +#define PB0_RPORT PINB +#define PB0_WPORT PORTB +#define PB0_DDR DDRB +#define PB0_PWM NULL +#undef PB1 +#define PB1_PIN PINB1 +#define PB1_RPORT PINB +#define PB1_WPORT PORTB +#define PB1_DDR DDRB +#define PB1_PWM NULL +#undef PB2 +#define PB2_PIN PINB2 +#define PB2_RPORT PINB +#define PB2_WPORT PORTB +#define PB2_DDR DDRB +#define PB2_PWM NULL +#undef PB3 +#define PB3_PIN PINB3 +#define PB3_RPORT PINB +#define PB3_WPORT PORTB +#define PB3_DDR DDRB +#define PB3_PWM NULL +#undef PB4 +#define PB4_PIN PINB4 +#define PB4_RPORT PINB +#define PB4_WPORT PORTB +#define PB4_DDR DDRB +#define PB4_PWM &OCR2A +#undef PB5 +#define PB5_PIN PINB5 +#define PB5_RPORT PINB +#define PB5_WPORT PORTB +#define PB5_DDR DDRB +#define PB5_PWM NULL +#undef PB6 +#define PB6_PIN PINB6 +#define PB6_RPORT PINB +#define PB6_WPORT PORTB +#define PB6_DDR DDRB +#define PB6_PWM NULL +#undef PB7 +#define PB7_PIN PINB7 +#define PB7_RPORT PINB +#define PB7_WPORT PORTB +#define PB7_DDR DDRB +#define PB7_PWM &OCR0A + +#undef PC0 +#define PC0_PIN PINC0 +#define PC0_RPORT PINC +#define PC0_WPORT PORTC +#define PC0_DDR DDRC +#define PC0_PWM NULL +#undef PC1 +#define PC1_PIN PINC1 +#define PC1_RPORT PINC +#define PC1_WPORT PORTC +#define PC1_DDR DDRC +#define PC1_PWM NULL +#undef PC2 +#define PC2_PIN PINC2 +#define PC2_RPORT PINC +#define PC2_WPORT PORTC +#define PC2_DDR DDRC +#define PC2_PWM NULL +#undef PC3 +#define PC3_PIN PINC3 +#define PC3_RPORT PINC +#define PC3_WPORT PORTC +#define PC3_DDR DDRC +#define PC3_PWM NULL +#undef PC4 +#define PC4_PIN PINC4 +#define PC4_RPORT PINC +#define PC4_WPORT PORTC +#define PC4_DDR DDRC +#define PC4_PWM NULL +#undef PC5 +#define PC5_PIN PINC5 +#define PC5_RPORT PINC +#define PC5_WPORT PORTC +#define PC5_DDR DDRC +#define PC5_PWM NULL +#undef PC6 +#define PC6_PIN PINC6 +#define PC6_RPORT PINC +#define PC6_WPORT PORTC +#define PC6_DDR DDRC +#define PC6_PWM NULL +#undef PC7 +#define PC7_PIN PINC7 +#define PC7_RPORT PINC +#define PC7_WPORT PORTC +#define PC7_DDR DDRC +#define PC7_PWM NULL + +#undef PD0 +#define PD0_PIN PIND0 +#define PD0_RPORT PIND +#define PD0_WPORT PORTD +#define PD0_DDR DDRD +#define PD0_PWM NULL +#undef PD1 +#define PD1_PIN PIND1 +#define PD1_RPORT PIND +#define PD1_WPORT PORTD +#define PD1_DDR DDRD +#define PD1_PWM NULL +#undef PD2 +#define PD2_PIN PIND2 +#define PD2_RPORT PIND +#define PD2_WPORT PORTD +#define PD2_DDR DDRD +#define PD2_PWM NULL +#undef PD3 +#define PD3_PIN PIND3 +#define PD3_RPORT PIND +#define PD3_WPORT PORTD +#define PD3_DDR DDRD +#define PD3_PWM NULL +#undef PD4 +#define PD4_PIN PIND4 +#define PD4_RPORT PIND +#define PD4_WPORT PORTD +#define PD4_DDR DDRD +#define PD4_PWM NULL +#undef PD5 +#define PD5_PIN PIND5 +#define PD5_RPORT PIND +#define PD5_WPORT PORTD +#define PD5_DDR DDRD +#define PD5_PWM NULL +#undef PD6 +#define PD6_PIN PIND6 +#define PD6_RPORT PIND +#define PD6_WPORT PORTD +#define PD6_DDR DDRD +#define PD6_PWM NULL +#undef PD7 +#define PD7_PIN PIND7 +#define PD7_RPORT PIND +#define PD7_WPORT PORTD +#define PD7_DDR DDRD +#define PD7_PWM NULL + +#undef PE0 +#define PE0_PIN PINE0 +#define PE0_RPORT PINE +#define PE0_WPORT PORTE +#define PE0_DDR DDRE +#define PE0_PWM NULL +#undef PE1 +#define PE1_PIN PINE1 +#define PE1_RPORT PINE +#define PE1_WPORT PORTE +#define PE1_DDR DDRE +#define PE1_PWM NULL +#undef PE2 +#define PE2_PIN PINE2 +#define PE2_RPORT PINE +#define PE2_WPORT PORTE +#define PE2_DDR DDRE +#define PE2_PWM NULL +#undef PE3 +#define PE3_PIN PINE3 +#define PE3_RPORT PINE +#define PE3_WPORT PORTE +#define PE3_DDR DDRE +#define PE3_PWM &OCR3AL +#undef PE4 +#define PE4_PIN PINE4 +#define PE4_RPORT PINE +#define PE4_WPORT PORTE +#define PE4_DDR DDRE +#define PE4_PWM &OCR3BL +#undef PE5 +#define PE5_PIN PINE5 +#define PE5_RPORT PINE +#define PE5_WPORT PORTE +#define PE5_DDR DDRE +#define PE5_PWM &OCR3CL +#undef PE6 +#define PE6_PIN PINE6 +#define PE6_RPORT PINE +#define PE6_WPORT PORTE +#define PE6_DDR DDRE +#define PE6_PWM NULL +#undef PE7 +#define PE7_PIN PINE7 +#define PE7_RPORT PINE +#define PE7_WPORT PORTE +#define PE7_DDR DDRE +#define PE7_PWM NULL + +#undef PF0 +#define PF0_PIN PINF0 +#define PF0_RPORT PINF +#define PF0_WPORT PORTF +#define PF0_DDR DDRF +#define PF0_PWM NULL +#undef PF1 +#define PF1_PIN PINF1 +#define PF1_RPORT PINF +#define PF1_WPORT PORTF +#define PF1_DDR DDRF +#define PF1_PWM NULL +#undef PF2 +#define PF2_PIN PINF2 +#define PF2_RPORT PINF +#define PF2_WPORT PORTF +#define PF2_DDR DDRF +#define PF2_PWM NULL +#undef PF3 +#define PF3_PIN PINF3 +#define PF3_RPORT PINF +#define PF3_WPORT PORTF +#define PF3_DDR DDRF +#define PF3_PWM NULL +#undef PF4 +#define PF4_PIN PINF4 +#define PF4_RPORT PINF +#define PF4_WPORT PORTF +#define PF4_DDR DDRF +#define PF4_PWM NULL +#undef PF5 +#define PF5_PIN PINF5 +#define PF5_RPORT PINF +#define PF5_WPORT PORTF +#define PF5_DDR DDRF +#define PF5_PWM NULL +#undef PF6 +#define PF6_PIN PINF6 +#define PF6_RPORT PINF +#define PF6_WPORT PORTF +#define PF6_DDR DDRF +#define PF6_PWM NULL +#undef PF7 +#define PF7_PIN PINF7 +#define PF7_RPORT PINF +#define PF7_WPORT PORTF +#define PF7_DDR DDRF +#define PF7_PWM NULL + +#undef PG0 +#define PG0_PIN PING0 +#define PG0_RPORT PING +#define PG0_WPORT PORTG +#define PG0_DDR DDRG +#define PG0_PWM NULL +#undef PG1 +#define PG1_PIN PING1 +#define PG1_RPORT PING +#define PG1_WPORT PORTG +#define PG1_DDR DDRG +#define PG1_PWM NULL +#undef PG2 +#define PG2_PIN PING2 +#define PG2_RPORT PING +#define PG2_WPORT PORTG +#define PG2_DDR DDRG +#define PG2_PWM NULL +#undef PG3 +#define PG3_PIN PING3 +#define PG3_RPORT PING +#define PG3_WPORT PORTG +#define PG3_DDR DDRG +#define PG3_PWM NULL +#undef PG4 +#define PG4_PIN PING4 +#define PG4_RPORT PING +#define PG4_WPORT PORTG +#define PG4_DDR DDRG +#define PG4_PWM NULL +#undef PG5 +#define PG5_PIN PING5 +#define PG5_RPORT PING +#define PG5_WPORT PORTG +#define PG5_DDR DDRG +#define PG5_PWM &OCR0B + + +#endif + #ifndef DIO0_PIN #error pins for this chip not defined in arduino.h! If you write an appropriate pin definition and have this firmware work on your chip, please submit a pull request #endif -#endif /* _FASTIO_ARDUINO_H */ +#endif /* _FASTIO_ARDUINO_H */ diff --git a/Marlin/pins.h b/Marlin/pins.h index 044f083f8d..140525f685 100644 --- a/Marlin/pins.h +++ b/Marlin/pins.h @@ -14,7 +14,7 @@ #define DIGIPOTSS_PIN -1 #if MOTHERBOARD == 99 -#define KNOWN_BOARD 1 +#define KNOWN_BOARD 1 #define X_STEP_PIN 2 #define X_DIR_PIN 3 @@ -227,8 +227,8 @@ #endif //x axis pins - #define X_STEP_PIN 21 //different from stanard GEN7 - #define X_DIR_PIN 20 //different from stanard GEN7 + #define X_STEP_PIN 21 // different from standard GEN7 + #define X_DIR_PIN 20 // different from standard GEN7 #define X_ENABLE_PIN 24 #define X_STOP_PIN 0 @@ -248,14 +248,14 @@ #define E0_STEP_PIN 28 #define E0_DIR_PIN 27 #define E0_ENABLE_PIN 24 - + #define TEMP_0_PIN 2 #define TEMP_1_PIN -1 #define TEMP_2_PIN -1 #define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed) - + #define HEATER_0_PIN 4 - #define HEATER_1_PIN -1 + #define HEATER_1_PIN -1 #define HEATER_2_PIN -1 #define HEATER_BED_PIN 3 // (bed) @@ -272,33 +272,25 @@ //our RS485 pins //#define TX_ENABLE_PIN 12 //#define RX_ENABLE_PIN 13 - - #define BEEPER -1 - #define SDCARDDETECT -1 - #define SUICIDE_PIN -1 //has to be defined; otherwise Power_off doesn't work - + + #define BEEPER -1 + #define SDCARDDETECT -1 + #define SUICIDE_PIN -1 //has to be defined; otherwise Power_off doesn't work + #define KILL_PIN -1 - //Pins for 4bit LCD Support - #define LCD_PINS_RS 18 + //Pins for 4bit LCD Support + #define LCD_PINS_RS 18 #define LCD_PINS_ENABLE 17 #define LCD_PINS_D4 16 - #define LCD_PINS_D5 15 + #define LCD_PINS_D5 15 #define LCD_PINS_D6 13 #define LCD_PINS_D7 14 - + //buttons are directly attached #define BTN_EN1 11 #define BTN_EN2 10 #define BTN_ENC 12 //the click - - #define BLEN_C 2 - #define BLEN_B 1 - #define BLEN_A 0 - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 #endif /**************************************************************************************** @@ -321,202 +313,206 @@ #if MOTHERBOARD == 33 || MOTHERBOARD == 34 -#define LARGE_FLASH true + #define LARGE_FLASH true -#define X_STEP_PIN 54 -#define X_DIR_PIN 55 -#define X_ENABLE_PIN 38 -#define X_MIN_PIN 3 -#define X_MAX_PIN 2 + #define X_STEP_PIN 54 + #define X_DIR_PIN 55 + #define X_ENABLE_PIN 38 + #define X_MIN_PIN 3 + #define X_MAX_PIN 2 -#define Y_STEP_PIN 60 -#define Y_DIR_PIN 61 -#define Y_ENABLE_PIN 56 -#define Y_MIN_PIN 14 -#define Y_MAX_PIN 15 + #define Y_STEP_PIN 60 + #define Y_DIR_PIN 61 + #define Y_ENABLE_PIN 56 + #define Y_MIN_PIN 14 + #define Y_MAX_PIN 15 -#define Z_STEP_PIN 46 -#define Z_DIR_PIN 48 -#define Z_ENABLE_PIN 62 -#define Z_MIN_PIN 18 -#define Z_MAX_PIN 19 + #define Z_STEP_PIN 46 + #define Z_DIR_PIN 48 + #define Z_ENABLE_PIN 62 + #define Z_MIN_PIN 18 + #define Z_MAX_PIN 19 -#define Z2_STEP_PIN 36 -#define Z2_DIR_PIN 34 -#define Z2_ENABLE_PIN 30 + #define Z2_STEP_PIN 36 + #define Z2_DIR_PIN 34 + #define Z2_ENABLE_PIN 30 -#define E0_STEP_PIN 26 -#define E0_DIR_PIN 28 -#define E0_ENABLE_PIN 24 + #define E0_STEP_PIN 26 + #define E0_DIR_PIN 28 + #define E0_ENABLE_PIN 24 -#define E1_STEP_PIN 36 -#define E1_DIR_PIN 34 -#define E1_ENABLE_PIN 30 + #define E1_STEP_PIN 36 + #define E1_DIR_PIN 34 + #define E1_ENABLE_PIN 30 -#define SDPOWER -1 -#define SDSS 53 -#define LED_PIN 13 + #define SDPOWER -1 + #define SDSS 53 + #define LED_PIN 13 -#if MOTHERBOARD == 33 -#define FAN_PIN 9 // (Sprinter config) -#else -#define FAN_PIN 4 // IO pin. Buffer needed -#endif -#define PS_ON_PIN 12 + #if MOTHERBOARD == 33 + #define FAN_PIN 9 // (Sprinter config) + #else + #define FAN_PIN 4 // IO pin. Buffer needed + #endif -#if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL) -#define KILL_PIN 41 -#else -#define KILL_PIN -1 -#endif + #define PS_ON_PIN 12 -#define HEATER_0_PIN 10 // EXTRUDER 1 -#if MOTHERBOARD == 33 -#define HEATER_1_PIN -1 -#else -#define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter) -#endif -#define HEATER_2_PIN -1 -#define TEMP_0_PIN 13 // ANALOG NUMBERING -#define TEMP_1_PIN 15 // ANALOG NUMBERING -#define TEMP_2_PIN -1 // ANALOG NUMBERING -#define HEATER_BED_PIN 8 // BED -#define TEMP_BED_PIN 14 // ANALOG NUMBERING + #if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL) + #define KILL_PIN 41 + #else + #define KILL_PIN -1 + #endif -#ifdef ULTRA_LCD + #define HEATER_0_PIN 10 // EXTRUDER 1 - #ifdef NEWPANEL - //encoder rotation values - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 + #if MOTHERBOARD == 33 + #define HEATER_1_PIN -1 + #else + #define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter) + #endif - #define BLEN_A 0 - #define BLEN_B 1 - #define BLEN_C 2 + #define HEATER_2_PIN -1 + #define TEMP_0_PIN 13 // ANALOG NUMBERING + #define TEMP_1_PIN 15 // ANALOG NUMBERING + #define TEMP_2_PIN -1 // ANALOG NUMBERING + #define HEATER_BED_PIN 8 // BED + #define TEMP_BED_PIN 14 // ANALOG NUMBERING - #define LCD_PINS_RS 16 - #define LCD_PINS_ENABLE 17 - #define LCD_PINS_D4 23 - #define LCD_PINS_D5 25 - #define LCD_PINS_D6 27 - #define LCD_PINS_D7 29 - - #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER - #define BEEPER 37 - #define BTN_EN1 31 - #define BTN_EN2 33 - #define BTN_ENC 35 - #define SDCARDDETECT 49 - #else - //arduino pin which triggers an piezzo beeper - #define BEEPER 33 // Beeper on AUX-4 + #ifdef NUM_SERVOS + #define SERVO0_PIN 11 - //buttons are directly attached using AUX-2 - #define BTN_EN1 37 - #define BTN_EN2 35 - #define BTN_ENC 31 //the click - - #ifdef G3D_PANEL - #define SDCARDDETECT 49 - #else - #define SDCARDDETECT -1 // Ramps does not use this port - #endif + #if NUM_SERVOS > 1 + #define SERVO1_PIN 6 #endif - #else //old style panel with shift register - //arduino pin witch triggers an piezzo beeper - #define BEEPER 33 // No Beeper added + #if NUM_SERVOS > 2 + #define SERVO2_PIN 5 + #endif - //buttons are attached to a shift register - // Not wired this yet - //#define SHIFT_CLK 38 - //#define SHIFT_LD 42 - //#define SHIFT_OUT 40 - //#define SHIFT_EN 17 - - #define LCD_PINS_RS 16 - #define LCD_PINS_ENABLE 17 - #define LCD_PINS_D4 23 - #define LCD_PINS_D5 25 - #define LCD_PINS_D6 27 - #define LCD_PINS_D7 29 - - //encoder rotation values - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 + #if NUM_SERVOS > 2 + #define SERVO3_PIN 4 + #endif + #endif - - //bits in the shift register that carry the buttons for: - // left up center down right red - #define BL_LE 7 - #define BL_UP 6 - #define BL_MI 5 - #define BL_DW 4 - #define BL_RI 3 - #define BL_ST 2 + #ifdef ULTRA_LCD - #define BLEN_B 1 - #define BLEN_A 0 - #endif -#endif //ULTRA_LCD + #ifdef NEWPANEL + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #define LCD_PINS_D7 29 + + #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER + #define BEEPER 37 + + #define BTN_EN1 31 + #define BTN_EN2 33 + #define BTN_ENC 35 + + #define SDCARDDETECT 49 + #else + //arduino pin which triggers an piezzo beeper + #define BEEPER 33 // Beeper on AUX-4 + + //buttons are directly attached using AUX-2 + #ifdef REPRAPWORLD_KEYPAD + #define BTN_EN1 64 // encoder + #define BTN_EN2 59 // encoder + #define BTN_ENC 63 // enter button + #define SHIFT_OUT 40 // shift register + #define SHIFT_CLK 44 // shift register + #define SHIFT_LD 42 // shift register + #else + #define BTN_EN1 37 + #define BTN_EN2 35 + #define BTN_ENC 31 //the click + #endif + + #ifdef G3D_PANEL + #define SDCARDDETECT 49 + #else + #define SDCARDDETECT -1 // Ramps does not use this port + #endif + + #endif + + #else //old style panel with shift register + //arduino pin witch triggers an piezzo beeper + #define BEEPER 33 // No Beeper added + + //buttons are attached to a shift register + // Not wired this yet + //#define SHIFT_CLK 38 + //#define SHIFT_LD 42 + //#define SHIFT_OUT 40 + //#define SHIFT_EN 17 + + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #define LCD_PINS_D7 29 + #endif + #endif //ULTRA_LCD #else // RAMPS_V_1_1 or RAMPS_V_1_2 as default (MOTHERBOARD == 3) -#define X_STEP_PIN 26 -#define X_DIR_PIN 28 -#define X_ENABLE_PIN 24 -#define X_MIN_PIN 3 -#define X_MAX_PIN -1 //2 + #define X_STEP_PIN 26 + #define X_DIR_PIN 28 + #define X_ENABLE_PIN 24 + #define X_MIN_PIN 3 + #define X_MAX_PIN -1 //2 -#define Y_STEP_PIN 38 -#define Y_DIR_PIN 40 -#define Y_ENABLE_PIN 36 -#define Y_MIN_PIN 16 -#define Y_MAX_PIN -1 //17 + #define Y_STEP_PIN 38 + #define Y_DIR_PIN 40 + #define Y_ENABLE_PIN 36 + #define Y_MIN_PIN 16 + #define Y_MAX_PIN -1 //17 -#define Z_STEP_PIN 44 -#define Z_DIR_PIN 46 -#define Z_ENABLE_PIN 42 -#define Z_MIN_PIN 18 -#define Z_MAX_PIN -1 //19 + #define Z_STEP_PIN 44 + #define Z_DIR_PIN 46 + #define Z_ENABLE_PIN 42 + #define Z_MIN_PIN 18 + #define Z_MAX_PIN -1 //19 -#define E0_STEP_PIN 32 -#define E0_DIR_PIN 34 -#define E0_ENABLE_PIN 30 + #define E0_STEP_PIN 32 + #define E0_DIR_PIN 34 + #define E0_ENABLE_PIN 30 -#define SDPOWER 48 -#define SDSS 53 -#define LED_PIN 13 -#define PS_ON_PIN -1 -#define KILL_PIN -1 + #define SDPOWER 48 + #define SDSS 53 + #define LED_PIN 13 + #define PS_ON_PIN -1 + #define KILL_PIN -1 + + #ifdef RAMPS_V_1_0 // RAMPS_V_1_0 + #define HEATER_0_PIN 12 // RAMPS 1.0 + #define HEATER_BED_PIN -1 // RAMPS 1.0 + #define FAN_PIN 11 // RAMPS 1.0 + #else // RAMPS_V_1_1 or RAMPS_V_1_2 + #define HEATER_0_PIN 10 // RAMPS 1.1 + #define HEATER_BED_PIN 8 // RAMPS 1.1 + #define FAN_PIN 9 // RAMPS 1.1 + #endif + + #define HEATER_1_PIN -1 + #define HEATER_2_PIN -1 + #define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! + #define TEMP_1_PIN -1 + #define TEMP_2_PIN -1 + #define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! -#ifdef RAMPS_V_1_0 // RAMPS_V_1_0 - #define HEATER_0_PIN 12 // RAMPS 1.0 - #define HEATER_BED_PIN -1 // RAMPS 1.0 - #define FAN_PIN 11 // RAMPS 1.0 -#else // RAMPS_V_1_1 or RAMPS_V_1_2 - #define HEATER_0_PIN 10 // RAMPS 1.1 - #define HEATER_BED_PIN 8 // RAMPS 1.1 - #define FAN_PIN 9 // RAMPS 1.1 -#endif -#define HEATER_1_PIN -1 -#define HEATER_2_PIN -1 -#define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! -#define TEMP_1_PIN -1 -#define TEMP_2_PIN -1 -#define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #endif// MOTHERBOARD == 33 || MOTHERBOARD == 34 -// SPI for Max6675 Thermocouple +// SPI for Max6675 Thermocouple #ifndef SDSUPPORT -// these pins are defined in the SD library if building with SD support +// these pins are defined in the SD library if building with SD support #define MAX_SCK_PIN 52 #define MAX_MISO_PIN 50 #define MAX_MOSI_PIN 51 @@ -568,8 +564,8 @@ #define HEATER_1_PIN -1 #define HEATER_2_PIN -1 #define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! -#define TEMP_1_PIN -1 -#define TEMP_2_PIN -1 +#define TEMP_1_PIN -1 +#define TEMP_2_PIN -1 #define HEATER_BED_PIN -1 #define TEMP_BED_PIN -1 @@ -632,14 +628,14 @@ #define PS_ON_PIN -1 //changed @ rkoeppl 20110410 #define KILL_PIN -1 //changed @ drakelive 20120830 //our pin for debugging. - - #define DEBUG_PIN 0 - - //our RS485 pins - #define TX_ENABLE_PIN 12 - #define RX_ENABLE_PIN 13 - + #define DEBUG_PIN 0 + + //our RS485 pins + #define TX_ENABLE_PIN 12 + #define RX_ENABLE_PIN 13 + + #endif /**************************************************************************************** @@ -655,7 +651,7 @@ #if MOTHERBOARD == 62 || MOTHERBOARD == 63 || MOTHERBOARD == 64 #undef MOTHERBOARD #define MOTHERBOARD 6 -#define SANGUINOLOLU_V_1_2 +#define SANGUINOLOLU_V_1_2 #endif #if MOTHERBOARD == 6 #define KNOWN_BOARD 1 @@ -682,7 +678,7 @@ #define LED_PIN -1 -#define FAN_PIN -1 +#define FAN_PIN -1 #if FAN_PIN == 12 || FAN_PIN ==13 #define FAN_SOFT_PWM #endif @@ -736,46 +732,44 @@ //we have no buzzer installed #define BEEPER -1 //LCD Pins - #ifdef DOGLCD - // Pins for DOGM SPI LCD Support - #define DOGLCD_A0 30 - #define DOGLCD_CS 29 - // GLCD features - #define LCD_CONTRAST 1 - // Uncomment screen orientation - // #define LCD_SCREEN_ROT_0 - // #define LCD_SCREEN_ROT_90 - #define LCD_SCREEN_ROT_180 - // #define LCD_SCREEN_ROT_270 - #else // standard Hitachi LCD controller - #define LCD_PINS_RS 4 - #define LCD_PINS_ENABLE 17 - #define LCD_PINS_D4 30 - #define LCD_PINS_D5 29 - #define LCD_PINS_D6 28 - #define LCD_PINS_D7 27 - #endif + #ifdef DOGLCD + // Pins for DOGM SPI LCD Support + #define DOGLCD_A0 30 + #define DOGLCD_CS 29 + // GLCD features + #define LCD_CONTRAST 1 + // Uncomment screen orientation + // #define LCD_SCREEN_ROT_0 + // #define LCD_SCREEN_ROT_90 + #define LCD_SCREEN_ROT_180 + // #define LCD_SCREEN_ROT_270 + #else // standard Hitachi LCD controller + #define LCD_PINS_RS 4 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 30 + #define LCD_PINS_D5 29 + #define LCD_PINS_D6 28 + #define LCD_PINS_D7 27 + #endif //The encoder and click button - #define BTN_EN1 11 //must be a hardware interrupt pin - #define BTN_EN2 10 //must be hardware interrupt pin - #define BTN_ENC 16 //the switch + #define BTN_EN1 11 + #define BTN_EN2 10 + #ifdef LCD_I2C_PANELOLU2 + #ifdef MELZI + #define BTN_ENC 29 //the click switch + #define SDSS 30 //to use the SD card reader on the Panelolu2 rather than the melzi board + #else + #define BTN_ENC 30 //the click switch + #endif + #else + #define BTN_ENC 16 //the click switch + #endif //Panelolu2 //not connected to a pin - #define SDCARDDETECT -1 - - //from the same bit in the RAMPS Newpanel define - //encoder rotation values - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 - - #define BLEN_C 2 - #define BLEN_B 1 - #define BLEN_A 0 - + #define SDCARDDETECT -1 + #endif //Newpanel #endif //Ultipanel - + #endif @@ -805,17 +799,17 @@ #define Y_MAX_PIN 28 #define Y_ENABLE_PIN 29 -#define Z_STEP_PIN 37 +#define Z_STEP_PIN 37 #define Z_DIR_PIN 39 #define Z_MIN_PIN 30 #define Z_MAX_PIN 32 #define Z_ENABLE_PIN 35 -#define HEATER_BED_PIN 4 -#define TEMP_BED_PIN 10 +#define HEATER_BED_PIN 4 +#define TEMP_BED_PIN 10 #define HEATER_0_PIN 2 -#define TEMP_0_PIN 8 +#define TEMP_0_PIN 8 #define HEATER_1_PIN 3 #define TEMP_1_PIN 9 @@ -845,29 +839,20 @@ //arduino pin witch triggers an piezzo beeper #define BEEPER 18 - #define LCD_PINS_RS 20 + #define LCD_PINS_RS 20 #define LCD_PINS_ENABLE 17 #define LCD_PINS_D4 16 - #define LCD_PINS_D5 21 + #define LCD_PINS_D5 21 #define LCD_PINS_D6 5 #define LCD_PINS_D7 6 - + //buttons are directly attached #define BTN_EN1 40 #define BTN_EN2 42 #define BTN_ENC 19 //the click - #define BLEN_C 2 - #define BLEN_B 1 - #define BLEN_A 0 - #define SDCARDDETECT 38 - //encoder rotation values - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 #else //old style panel with shift register //arduino pin witch triggers an piezzo beeper #define BEEPER 18 @@ -877,40 +862,15 @@ #define SHIFT_LD 42 #define SHIFT_OUT 40 #define SHIFT_EN 17 - - #define LCD_PINS_RS 16 + + #define LCD_PINS_RS 16 #define LCD_PINS_ENABLE 5 #define LCD_PINS_D4 6 - #define LCD_PINS_D5 21 + #define LCD_PINS_D5 21 #define LCD_PINS_D6 20 #define LCD_PINS_D7 19 - - //encoder rotation values - #ifndef ULTIMAKERCONTROLLER - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 - #else - #define encrot0 0 - #define encrot1 1 - #define encrot2 3 - #define encrot3 2 - - #endif - + #define SDCARDDETECT -1 - //bits in the shift register that carry the buttons for: - // left up center down right red - #define BL_LE 7 - #define BL_UP 6 - #define BL_MI 5 - #define BL_DW 4 - #define BL_RI 3 - #define BL_ST 2 - - #define BLEN_B 1 - #define BLEN_A 0 #endif #endif //ULTRA_LCD @@ -942,17 +902,17 @@ #define Y_MAX_PIN 16 #define Y_ENABLE_PIN 29 -#define Z_STEP_PIN 37 +#define Z_STEP_PIN 37 #define Z_DIR_PIN 39 #define Z_MIN_PIN 19 #define Z_MAX_PIN 18 #define Z_ENABLE_PIN 35 -#define HEATER_BED_PIN -1 -#define TEMP_BED_PIN -1 +#define HEATER_BED_PIN -1 +#define TEMP_BED_PIN -1 #define HEATER_0_PIN 2 -#define TEMP_0_PIN 8 +#define TEMP_0_PIN 8 #define HEATER_1_PIN 1 #define TEMP_1_PIN 1 @@ -976,10 +936,10 @@ #define KILL_PIN -1 #define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. -#define LCD_PINS_RS 24 +#define LCD_PINS_RS 24 #define LCD_PINS_ENABLE 22 #define LCD_PINS_D4 36 -#define LCD_PINS_D5 34 +#define LCD_PINS_D5 34 #define LCD_PINS_D6 32 #define LCD_PINS_D7 30 @@ -1001,17 +961,17 @@ #define X_DIR_PIN 16 #define X_ENABLE_PIN 48 #define X_MIN_PIN 37 -#define X_MAX_PIN 36 +#define X_MAX_PIN 36 #define Y_STEP_PIN 54 -#define Y_DIR_PIN 47 +#define Y_DIR_PIN 47 #define Y_ENABLE_PIN 55 #define Y_MIN_PIN 35 -#define Y_MAX_PIN 34 +#define Y_MAX_PIN 34 -#define Z_STEP_PIN 57 +#define Z_STEP_PIN 57 #define Z_DIR_PIN 56 -#define Z_ENABLE_PIN 62 +#define Z_ENABLE_PIN 62 #define Z_MIN_PIN 33 #define Z_MAX_PIN 32 @@ -1029,45 +989,76 @@ #define LED_PIN 13 -#define FAN_PIN 7 +#define FAN_PIN 7 //additional FAN1 PIN (e.g. useful for electronics fan or light on/off) on PIN 8 #define PS_ON_PIN 45 #define KILL_PIN 46 -#define HEATER_0_PIN 2 // EXTRUDER 1 -#define HEATER_1_PIN 3 // EXTRUDER 2 -#define HEATER_2_PIN 6 // EXTRUDER 3 -//optional FAN1 can be used as 4th heater output: #define HEATER_3_PIN 8 // EXTRUDER 4 -#define HEATER_BED_PIN 9 // BED +#if (TEMP_SENSOR_0==0) + #define TEMP_0_PIN -1 + #define HEATER_0_PIN -1 +#else + #define HEATER_0_PIN 2 // EXTRUDER 1 + #if (TEMP_SENSOR_0==-1) + #define TEMP_0_PIN 6 // ANALOG NUMBERING - connector *K1* on RUMBA thermocouple ADD ON is used + #else + #define TEMP_0_PIN 15 // ANALOG NUMBERING - default connector for thermistor *T0* on rumba board is used + #endif +#endif -#define TEMP_0_PIN 15 // ANALOG NUMBERING -#define TEMP_1_PIN 14 // ANALOG NUMBERING -#define TEMP_2_PIN 13 // ANALOG NUMBERING -//optional for extruder 4 or chamber: #define TEMP_2_PIN 12 // ANALOG NUMBERING -#define TEMP_BED_PIN 11 // ANALOG NUMBERING +#if (TEMP_SENSOR_1==0) + #define TEMP_1_PIN -1 + #define HEATER_1_PIN -1 +#else + #define HEATER_1_PIN 3 // EXTRUDER 2 + #if (TEMP_SENSOR_1==-1) + #define TEMP_1_PIN 5 // ANALOG NUMBERING - connector *K2* on RUMBA thermocouple ADD ON is used + #else + #define TEMP_1_PIN 14 // ANALOG NUMBERING - default connector for thermistor *T1* on rumba board is used + #endif +#endif + +#if (TEMP_SENSOR_2==0) + #define TEMP_2_PIN -1 + #define HEATER_2_PIN -1 +#else + #define HEATER_2_PIN 6 // EXTRUDER 3 + #if (TEMP_SENSOR_2==-1) + #define TEMP_2_PIN 7 // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple + #else + #define TEMP_2_PIN 13 // ANALOG NUMBERING - default connector for thermistor *T2* on rumba board is used + #endif +#endif + +//optional for extruder 4 or chamber: #define TEMP_X_PIN 12 // ANALOG NUMBERING - default connector for thermistor *T3* on rumba board is used +//optional FAN1 can be used as 4th heater output: #define HEATER_3_PIN 8 // EXTRUDER 4 + +#if (TEMP_SENSOR_BED==0) + #define TEMP_BED_PIN -1 + #define HEATER_BED_PIN -1 +#else + #define HEATER_BED_PIN 9 // BED + #if (TEMP_SENSOR_BED==-1) + #define TEMP_BED_PIN 7 // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple + #else + #define TEMP_BED_PIN 11 // ANALOG NUMBERING - default connector for thermistor *THB* on rumba board is used + #endif +#endif #define SDPOWER -1 #define SDSS 53 #define SDCARDDETECT 49 #define BEEPER 44 -#define LCD_PINS_RS 19 +#define LCD_PINS_RS 19 #define LCD_PINS_ENABLE 42 #define LCD_PINS_D4 18 -#define LCD_PINS_D5 38 +#define LCD_PINS_D5 38 #define LCD_PINS_D6 41 #define LCD_PINS_D7 40 #define BTN_EN1 11 #define BTN_EN2 12 #define BTN_ENC 43 -//encoder rotation values -#define BLEN_C 2 -#define BLEN_B 1 -#define BLEN_A 0 -#define encrot0 0 -#define encrot1 2 -#define encrot2 3 -#define encrot3 1 #endif //MOTHERBOARD==80 @@ -1238,7 +1229,7 @@ #define LED_PIN -1 -#define FAN_PIN -1 +#define FAN_PIN -1 #define PS_ON_PIN 14 #define KILL_PIN -1 @@ -1277,7 +1268,7 @@ * MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25) * SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24) * RST 9| |32 AREF -* VCC 10| |31 GND +* VCC 10| |31 GND * GND 11| |30 AVCC * XTAL2 12| |29 PC7 (D 23) * XTAL1 13| |28 PC6 (D 22) @@ -1334,7 +1325,7 @@ #define KILL_PIN -1 #define HEATER_0_PIN 4 -#define HEATER_1_PIN -1 // 12 +#define HEATER_1_PIN -1 // 12 #define HEATER_2_PIN -1 // 13 #define TEMP_0_PIN 0 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_1_PIN -1 // 1 @@ -1372,12 +1363,12 @@ #define E0_ENABLE_PIN 10 /* future proofing */ -#define __FS 20 -#define __FD 19 -#define __GS 18 -#define __GD 13 +#define __FS 20 +#define __FD 19 +#define __GS 18 +#define __GD 13 -#define UNUSED_PWM 14 /* PWM on LEFT connector */ +#define UNUSED_PWM 14 /* PWM on LEFT connector */ #define E1_STEP_PIN -1 // 21 #define E1_DIR_PIN -1 // 20 @@ -1396,18 +1387,18 @@ #define KILL_PIN -1 #define HEATER_0_PIN 3 /*DONE PWM on RIGHT connector */ -#define HEATER_1_PIN -1 +#define HEATER_1_PIN -1 #define HEATER_2_PIN -1 -#define HEATER_1_PIN -1 +#define HEATER_1_PIN -1 #define HEATER_2_PIN -1 -#define TEMP_0_PIN 0 // ANALOG INPUT NUMBERING +#define TEMP_0_PIN 0 // ANALOG INPUT NUMBERING #define TEMP_1_PIN 1 // ANALOG #define TEMP_2_PIN -1 // 2 #define HEATER_BED_PIN 4 #define TEMP_BED_PIN 2 // 1,2 or I2C -#define I2C_SCL 16 -#define I2C_SDA 17 +#define I2C_SCL 16 +#define I2C_SDA 17 #endif @@ -1448,7 +1439,7 @@ #define Z_MS2_PIN 67 #define HEATER_BED_PIN 3 -#define TEMP_BED_PIN 2 +#define TEMP_BED_PIN 2 #define HEATER_0_PIN 9 #define TEMP_0_PIN 0 @@ -1456,7 +1447,11 @@ #define HEATER_1_PIN 7 #define TEMP_1_PIN 1 +#ifdef BARICUDA +#define HEATER_2_PIN 6 +#else #define HEATER_2_PIN -1 +#endif #define TEMP_2_PIN -1 #define E0_STEP_PIN 34 @@ -1491,7 +1486,6 @@ #if MOTHERBOARD == 70 #define KNOWN_BOARD 1 -//////////////////FIX THIS////////////// #ifndef __AVR_ATmega2560__ #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. @@ -1537,9 +1531,9 @@ #define HEATER_0_PIN 9 // EXTRUDER 1 #define HEATER_1_PIN 8 // EXTRUDER 2 (FAN On Sprinter) -#define HEATER_2_PIN -1 +#define HEATER_2_PIN -1 -#if TEMP_SENSOR_0 == -1 +#if TEMP_SENSOR_0 == -1 #define TEMP_0_PIN 8 // ANALOG NUMBERING #else #define TEMP_0_PIN 13 // ANALOG NUMBERING @@ -1551,21 +1545,21 @@ #define HEATER_BED_PIN 10 // BED #define TEMP_BED_PIN 14 // ANALOG NUMBERING -#define BEEPER 33 // Beeper on AUX-4 +#define BEEPER 33 // Beeper on AUX-4 #ifdef ULTRA_LCD #ifdef NEWPANEL //arduino pin which triggers an piezzo beeper - - #define LCD_PINS_RS 16 + + #define LCD_PINS_RS 16 #define LCD_PINS_ENABLE 17 #define LCD_PINS_D4 23 - #define LCD_PINS_D5 25 + #define LCD_PINS_D5 25 #define LCD_PINS_D6 27 #define LCD_PINS_D7 29 - + //buttons are directly attached using AUX-2 #define BTN_EN1 59 #define BTN_EN2 64 @@ -1587,12 +1581,220 @@ #endif +/**************************************************************************************** +* MegaTronics v2.0 +* +****************************************************************************************/ +#if MOTHERBOARD == 701 + #define KNOWN_BOARD 1 + + + #ifndef __AVR_ATmega2560__ + #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. + #endif + + #define LARGE_FLASH true + + #define X_STEP_PIN 26 + #define X_DIR_PIN 27 + #define X_ENABLE_PIN 25 + #define X_MIN_PIN 37 + #define X_MAX_PIN 40 //2 //Max endstops default to disabled "-1", set to commented value to enable. + + #define Y_STEP_PIN 4 // A6 + #define Y_DIR_PIN 54 // A0 + #define Y_ENABLE_PIN 5 + #define Y_MIN_PIN 41 + #define Y_MAX_PIN 38 //15 + + #define Z_STEP_PIN 56 // A2 + #define Z_DIR_PIN 60 // A6 + #define Z_ENABLE_PIN 55 // A1 + #define Z_MIN_PIN 18 + #define Z_MAX_PIN 19 + + #define E0_STEP_PIN 35 + #define E0_DIR_PIN 36 + #define E0_ENABLE_PIN 34 + + #define E1_STEP_PIN 29 + #define E1_DIR_PIN 39 + #define E1_ENABLE_PIN 28 + + #define E2_STEP_PIN 23 + #define E2_DIR_PIN 24 + #define E2_ENABLE_PIN 22 + + #define SDPOWER -1 + #define SDSS 53 + #define LED_PIN 13 + + #define FAN_PIN 7 + #define FAN2_PIN 6 + #define PS_ON_PIN 12 + #define KILL_PIN -1 + + #define HEATER_0_PIN 9 // EXTRUDER 1 + #define HEATER_1_PIN 8 // EXTRUDER 2 + #define HEATER_2_PIN -1 + + #if TEMP_SENSOR_0 == -1 + #define TEMP_0_PIN 4 // ANALOG NUMBERING + #else + #define TEMP_0_PIN 13 // ANALOG NUMBERING + #endif + + + #if TEMP_SENSOR_1 == -1 + #define TEMP_1_PIN 8 // ANALOG NUMBERING + #else + #define TEMP_1_PIN 15 // ANALOG NUMBERING + #endif + + #define TEMP_2_PIN -1 // ANALOG NUMBERING + + #define HEATER_BED_PIN 10 // BED + + #if TEMP_SENSOR_BED == -1 + #define TEMP_BED_PIN 8 // ANALOG NUMBERING + #else + #define TEMP_BED_PIN 14 // ANALOG NUMBERING + #endif + + #define BEEPER 64 + + + #define LCD_PINS_RS 14 + #define LCD_PINS_ENABLE 15 + #define LCD_PINS_D4 30 + #define LCD_PINS_D5 31 + #define LCD_PINS_D6 32 + #define LCD_PINS_D7 33 + + + //buttons are directly attached using keypad + #define BTN_EN1 61 + #define BTN_EN2 59 + #define BTN_ENC 43 //the click + + #define BLEN_C 2 + #define BLEN_B 1 + #define BLEN_A 0 + + #define SDCARDDETECT -1 // Megatronics does not use this port + + //encoder rotation values + #define encrot0 0 + #define encrot1 2 + #define encrot2 3 + #define encrot3 1 + +#endif + + +/**************************************************************************************** +* Minitronics v1.0 +* +****************************************************************************************/ +#if MOTHERBOARD == 702 + #define KNOWN_BOARD 1 + + + #ifndef __AVR_ATmega1281__ + #error Oops! Make sure you have 'Minitronics ' selected from the 'Tools -> Boards' menu. + #endif + + #define LARGE_FLASH true + + #define X_STEP_PIN 48 + #define X_DIR_PIN 47 + #define X_ENABLE_PIN 49 + #define X_MIN_PIN 5 + #define X_MAX_PIN -1 //2 //Max endstops default to disabled "-1", set to commented value to enable. + + #define Y_STEP_PIN 39 // A6 + #define Y_DIR_PIN 40 // A0 + #define Y_ENABLE_PIN 38 + #define Y_MIN_PIN 2 + #define Y_MAX_PIN -1 //15 + + #define Z_STEP_PIN 42 // A2 + #define Z_DIR_PIN 43 // A6 + #define Z_ENABLE_PIN 41 // A1 + #define Z_MIN_PIN 6 + #define Z_MAX_PIN -1 + + #define E0_STEP_PIN 45 + #define E0_DIR_PIN 44 + #define E0_ENABLE_PIN 27 + + #define E1_STEP_PIN 36 + #define E1_DIR_PIN 35 + #define E1_ENABLE_PIN 37 + + #define E2_STEP_PIN -1 + #define E2_DIR_PIN -1 + #define E2_ENABLE_PIN -1 + + #define SDPOWER -1 + #define SDSS 16 + #define LED_PIN 46 + + #define FAN_PIN 9 + #define FAN2_PIN -1 + #define PS_ON_PIN -1 + #define KILL_PIN -1 + + #define HEATER_0_PIN 7 // EXTRUDER 1 + #define HEATER_1_PIN 8 // EXTRUDER 2 + #define HEATER_2_PIN -1 + + + #define TEMP_0_PIN 7 // ANALOG NUMBERING + #define TEMP_1_PIN 6 // ANALOG NUMBERING + #define TEMP_2_PIN -1 // ANALOG NUMBERING + + #define HEATER_BED_PIN 3 // BED + #define TEMP_BED_PIN 6 // ANALOG NUMBERING + + #define BEEPER -1 + + + #define LCD_PINS_RS -1 + #define LCD_PINS_ENABLE -1 + #define LCD_PINS_D4 -1 + #define LCD_PINS_D5 -1 + #define LCD_PINS_D6 -1 + #define LCD_PINS_D7 -1 + + + //buttons are directly attached using keypad + #define BTN_EN1 -1 + #define BTN_EN2 -1 + #define BTN_ENC -1 //the click + + #define BLEN_C 2 + #define BLEN_B 1 + #define BLEN_A 0 + + #define SDCARDDETECT -1 // Megatronics does not use this port + + //encoder rotation values + #define encrot0 0 + #define encrot1 2 + #define encrot2 3 + #define encrot3 1 + +#endif + + + #ifndef KNOWN_BOARD #error Unknown MOTHERBOARD value in configuration.h #endif //List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those! -#define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN, HEATER_0_PIN, +#define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN, HEATER_0_PIN, #if EXTRUDERS > 1 #define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN, HEATER_1_PIN, #else @@ -1645,3 +1847,4 @@ _E0_PINS _E1_PINS _E2_PINS \ analogInputToDigitalPin(TEMP_0_PIN), analogInputToDigitalPin(TEMP_1_PIN), analogInputToDigitalPin(TEMP_2_PIN), analogInputToDigitalPin(TEMP_BED_PIN) } #endif + diff --git a/Marlin/planner.cpp b/Marlin/planner.cpp index e45c9d7ff9..fcebab938a 100644 --- a/Marlin/planner.cpp +++ b/Marlin/planner.cpp @@ -98,7 +98,7 @@ volatile unsigned char block_buffer_tail; // Index of the block to pro //=============================private variables ============================ //=========================================================================== #ifdef PREVENT_DANGEROUS_EXTRUDE -bool allow_cold_extrude=false; +float extrude_min_temp=EXTRUDE_MINTEMP; #endif #ifdef XY_FREQUENCY_LIMIT #define MAX_FREQ_TIME (1000000.0/XY_FREQUENCY_LIMIT) @@ -439,12 +439,20 @@ void check_axes_activity() unsigned char z_active = 0; unsigned char e_active = 0; unsigned char tail_fan_speed = fanSpeed; + #ifdef BARICUDA + unsigned char tail_valve_pressure = ValvePressure; + unsigned char tail_e_to_p_pressure = EtoPPressure; + #endif block_t *block; if(block_buffer_tail != block_buffer_head) { uint8_t block_index = block_buffer_tail; tail_fan_speed = block_buffer[block_index].fan_speed; + #ifdef BARICUDA + tail_valve_pressure = block_buffer[block_index].valve_pressure; + tail_e_to_p_pressure = block_buffer[block_index].e_to_p_pressure; + #endif while(block_index != block_buffer_head) { block = &block_buffer[block_index]; @@ -464,7 +472,7 @@ void check_axes_activity() disable_e1(); disable_e2(); } -#if FAN_PIN > -1 +#if defined(FAN_PIN) && FAN_PIN > -1 #ifndef FAN_SOFT_PWM #ifdef FAN_KICKSTART_TIME static unsigned long fan_kick_end; @@ -486,6 +494,16 @@ void check_axes_activity() #ifdef AUTOTEMP getHighESpeed(); #endif + +#ifdef BARICUDA + #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1 + analogWrite(HEATER_1_PIN,tail_valve_pressure); + #endif + + #if defined(HEATER_2_PIN) && HEATER_2_PIN > -1 + analogWrite(HEATER_2_PIN,tail_e_to_p_pressure); + #endif +#endif } @@ -519,7 +537,7 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa #ifdef PREVENT_DANGEROUS_EXTRUDE if(target[E_AXIS]!=position[E_AXIS]) { - if(degHotend(active_extruder)fan_speed = fanSpeed; + #ifdef BARICUDA + block->valve_pressure = ValvePressure; + block->e_to_p_pressure = EtoPPressure; + #endif // Compute direction bits for this block block->direction_bits = 0; @@ -582,8 +604,16 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa block->active_extruder = extruder; //enable active axes + #ifdef COREXY + if((block->steps_x != 0) || (block->steps_y != 0)) + { + enable_x(); + enable_y(); + } + #else if(block->steps_x != 0) enable_x(); if(block->steps_y != 0) enable_y(); + #endif #ifndef Z_LATE_ENABLE if(block->steps_z != 0) enable_z(); #endif @@ -888,12 +918,12 @@ uint8_t movesplanned() return (block_buffer_head-block_buffer_tail + BLOCK_BUFFER_SIZE) & (BLOCK_BUFFER_SIZE - 1); } -void allow_cold_extrudes(bool allow) -{ #ifdef PREVENT_DANGEROUS_EXTRUDE - allow_cold_extrude=allow; -#endif +void set_extrude_min_temp(float temp) +{ + extrude_min_temp=temp; } +#endif // Calculate the steps/s^2 acceleration rates, based on the mm/s^s void reset_acceleration_rates() diff --git a/Marlin/planner.h b/Marlin/planner.h index 9a904e5776..597eeb1c00 100644 --- a/Marlin/planner.h +++ b/Marlin/planner.h @@ -60,6 +60,10 @@ typedef struct { unsigned long final_rate; // The minimal rate at exit unsigned long acceleration_st; // acceleration steps/sec^2 unsigned long fan_speed; + #ifdef BARICUDA + unsigned long valve_pressure; + unsigned long e_to_p_pressure; + #endif volatile char busy; } block_t; @@ -135,7 +139,9 @@ FORCE_INLINE bool blocks_queued() return true; } -void allow_cold_extrudes(bool allow); +#ifdef PREVENT_DANGEROUS_EXTRUDE +void set_extrude_min_temp(float temp); +#endif void reset_acceleration_rates(); #endif diff --git a/Marlin/stepper.cpp b/Marlin/stepper.cpp index 10e8fae2dd..e25ba6453d 100644 --- a/Marlin/stepper.cpp +++ b/Marlin/stepper.cpp @@ -29,7 +29,7 @@ #include "language.h" #include "cardreader.h" #include "speed_lookuptable.h" -#if DIGIPOTSS_PIN > -1 +#if defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1 #include #endif @@ -353,7 +353,7 @@ ISR(TIMER1_COMPA_vect) count_direction[X_AXIS]=-1; CHECK_ENDSTOPS { - #if X_MIN_PIN > -1 + #if defined(X_MIN_PIN) && X_MIN_PIN > -1 bool x_min_endstop=(READ(X_MIN_PIN) != X_ENDSTOPS_INVERTING); if(x_min_endstop && old_x_min_endstop && (current_block->steps_x > 0)) { endstops_trigsteps[X_AXIS] = count_position[X_AXIS]; @@ -372,7 +372,7 @@ ISR(TIMER1_COMPA_vect) count_direction[X_AXIS]=1; CHECK_ENDSTOPS { - #if X_MAX_PIN > -1 + #if defined(X_MAX_PIN) && X_MAX_PIN > -1 bool x_max_endstop=(READ(X_MAX_PIN) != X_ENDSTOPS_INVERTING); if(x_max_endstop && old_x_max_endstop && (current_block->steps_x > 0)){ endstops_trigsteps[X_AXIS] = count_position[X_AXIS]; @@ -391,7 +391,7 @@ ISR(TIMER1_COMPA_vect) count_direction[Y_AXIS]=-1; CHECK_ENDSTOPS { - #if Y_MIN_PIN > -1 + #if defined(Y_MIN_PIN) && Y_MIN_PIN > -1 bool y_min_endstop=(READ(Y_MIN_PIN) != Y_ENDSTOPS_INVERTING); if(y_min_endstop && old_y_min_endstop && (current_block->steps_y > 0)) { endstops_trigsteps[Y_AXIS] = count_position[Y_AXIS]; @@ -409,7 +409,7 @@ ISR(TIMER1_COMPA_vect) count_direction[Y_AXIS]=1; CHECK_ENDSTOPS { - #if Y_MAX_PIN > -1 + #if defined(Y_MAX_PIN) && Y_MAX_PIN > -1 bool y_max_endstop=(READ(Y_MAX_PIN) != Y_ENDSTOPS_INVERTING); if(y_max_endstop && old_y_max_endstop && (current_block->steps_y > 0)){ endstops_trigsteps[Y_AXIS] = count_position[Y_AXIS]; @@ -452,7 +452,7 @@ ISR(TIMER1_COMPA_vect) count_direction[Z_AXIS]=-1; CHECK_ENDSTOPS { - #if Z_MIN_PIN > -1 + #if defined(Z_MIN_PIN) && Z_MIN_PIN > -1 bool z_min_endstop=(READ(Z_MIN_PIN) != Z_ENDSTOPS_INVERTING); if(z_min_endstop && old_z_min_endstop && (current_block->steps_z > 0)) { endstops_trigsteps[Z_AXIS] = count_position[Z_AXIS]; @@ -473,7 +473,7 @@ ISR(TIMER1_COMPA_vect) count_direction[Z_AXIS]=1; CHECK_ENDSTOPS { - #if Z_MAX_PIN > -1 + #if defined(Z_MAX_PIN) && Z_MAX_PIN > -1 bool z_max_endstop=(READ(Z_MAX_PIN) != Z_ENDSTOPS_INVERTING); if(z_max_endstop && old_z_max_endstop && (current_block->steps_z > 0)) { endstops_trigsteps[Z_AXIS] = count_position[Z_AXIS]; @@ -743,20 +743,20 @@ void st_init() microstep_init(); //Initialize Microstepping Pins //Initialize Dir Pins - #if X_DIR_PIN > -1 + #if defined(X_DIR_PIN) && X_DIR_PIN > -1 SET_OUTPUT(X_DIR_PIN); #endif - #if Y_DIR_PIN > -1 + #if defined(Y_DIR_PIN) && Y_DIR_PIN > -1 SET_OUTPUT(Y_DIR_PIN); #endif - #if Z_DIR_PIN > -1 + #if defined(Z_DIR_PIN) && Z_DIR_PIN > -1 SET_OUTPUT(Z_DIR_PIN); - #if defined(Z_DUAL_STEPPER_DRIVERS) && (Z2_DIR_PIN > -1) + #if defined(Z_DUAL_STEPPER_DRIVERS) && defined(Z2_DIR_PIN) && (Z2_DIR_PIN > -1) SET_OUTPUT(Z2_DIR_PIN); #endif #endif - #if E0_DIR_PIN > -1 + #if defined(E0_DIR_PIN) && E0_DIR_PIN > -1 SET_OUTPUT(E0_DIR_PIN); #endif #if defined(E1_DIR_PIN) && (E1_DIR_PIN > -1) @@ -768,24 +768,24 @@ void st_init() //Initialize Enable Pins - steppers default to disabled. - #if (X_ENABLE_PIN > -1) + #if defined(X_ENABLE_PIN) && X_ENABLE_PIN > -1 SET_OUTPUT(X_ENABLE_PIN); if(!X_ENABLE_ON) WRITE(X_ENABLE_PIN,HIGH); #endif - #if (Y_ENABLE_PIN > -1) + #if defined(Y_ENABLE_PIN) && Y_ENABLE_PIN > -1 SET_OUTPUT(Y_ENABLE_PIN); if(!Y_ENABLE_ON) WRITE(Y_ENABLE_PIN,HIGH); #endif - #if (Z_ENABLE_PIN > -1) + #if defined(Z_ENABLE_PIN) && Z_ENABLE_PIN > -1 SET_OUTPUT(Z_ENABLE_PIN); if(!Z_ENABLE_ON) WRITE(Z_ENABLE_PIN,HIGH); - #if defined(Z_DUAL_STEPPER_DRIVERS) && (Z2_ENABLE_PIN > -1) + #if defined(Z_DUAL_STEPPER_DRIVERS) && defined(Z2_ENABLE_PIN) && (Z2_ENABLE_PIN > -1) SET_OUTPUT(Z2_ENABLE_PIN); if(!Z_ENABLE_ON) WRITE(Z2_ENABLE_PIN,HIGH); #endif #endif - #if (E0_ENABLE_PIN > -1) + #if defined(E0_ENABLE_PIN) && (E0_ENABLE_PIN > -1) SET_OUTPUT(E0_ENABLE_PIN); if(!E_ENABLE_ON) WRITE(E0_ENABLE_PIN,HIGH); #endif @@ -800,42 +800,42 @@ void st_init() //endstops and pullups - #if X_MIN_PIN > -1 + #if defined(X_MIN_PIN) && X_MIN_PIN > -1 SET_INPUT(X_MIN_PIN); #ifdef ENDSTOPPULLUP_XMIN WRITE(X_MIN_PIN,HIGH); #endif #endif - #if Y_MIN_PIN > -1 + #if defined(Y_MIN_PIN) && Y_MIN_PIN > -1 SET_INPUT(Y_MIN_PIN); #ifdef ENDSTOPPULLUP_YMIN WRITE(Y_MIN_PIN,HIGH); #endif #endif - #if Z_MIN_PIN > -1 + #if defined(Z_MIN_PIN) && Z_MIN_PIN > -1 SET_INPUT(Z_MIN_PIN); #ifdef ENDSTOPPULLUP_ZMIN WRITE(Z_MIN_PIN,HIGH); #endif #endif - #if X_MAX_PIN > -1 + #if defined(X_MAX_PIN) && X_MAX_PIN > -1 SET_INPUT(X_MAX_PIN); #ifdef ENDSTOPPULLUP_XMAX WRITE(X_MAX_PIN,HIGH); #endif #endif - #if Y_MAX_PIN > -1 + #if defined(Y_MAX_PIN) && Y_MAX_PIN > -1 SET_INPUT(Y_MAX_PIN); #ifdef ENDSTOPPULLUP_YMAX WRITE(Y_MAX_PIN,HIGH); #endif #endif - #if Z_MAX_PIN > -1 + #if defined(Z_MAX_PIN) && Z_MAX_PIN > -1 SET_INPUT(Z_MAX_PIN); #ifdef ENDSTOPPULLUP_ZMAX WRITE(Z_MAX_PIN,HIGH); @@ -844,26 +844,26 @@ void st_init() //Initialize Step Pins - #if (X_STEP_PIN > -1) + #if defined(X_STEP_PIN) && (X_STEP_PIN > -1) SET_OUTPUT(X_STEP_PIN); WRITE(X_STEP_PIN,INVERT_X_STEP_PIN); disable_x(); #endif - #if (Y_STEP_PIN > -1) + #if defined(Y_STEP_PIN) && (Y_STEP_PIN > -1) SET_OUTPUT(Y_STEP_PIN); WRITE(Y_STEP_PIN,INVERT_Y_STEP_PIN); disable_y(); #endif - #if (Z_STEP_PIN > -1) + #if defined(Z_STEP_PIN) && (Z_STEP_PIN > -1) SET_OUTPUT(Z_STEP_PIN); WRITE(Z_STEP_PIN,INVERT_Z_STEP_PIN); - #if defined(Z_DUAL_STEPPER_DRIVERS) && (Z2_STEP_PIN > -1) + #if defined(Z_DUAL_STEPPER_DRIVERS) && defined(Z2_STEP_PIN) && (Z2_STEP_PIN > -1) SET_OUTPUT(Z2_STEP_PIN); WRITE(Z2_STEP_PIN,INVERT_Z_STEP_PIN); #endif disable_z(); #endif - #if (E0_STEP_PIN > -1) + #if defined(E0_STEP_PIN) && (E0_STEP_PIN > -1) SET_OUTPUT(E0_STEP_PIN); WRITE(E0_STEP_PIN,INVERT_E_STEP_PIN); disable_e0(); @@ -879,10 +879,6 @@ void st_init() disable_e2(); #endif - #ifdef CONTROLLERFAN_PIN - SET_OUTPUT(CONTROLLERFAN_PIN); //Set pin used for driver cooling fan - #endif - // waveform generation = 0100 = CTC TCCR1B &= ~(1< -1 + #if defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1 digitalWrite(DIGIPOTSS_PIN,LOW); // take the SS pin low to select the chip SPI.transfer(address); // send in the address and value via SPI: SPI.transfer(value); @@ -989,7 +985,7 @@ void digitalPotWrite(int address, int value) // From Arduino DigitalPotControl e void digipot_init() //Initialize Digipot Motor Current { - #if DIGIPOTSS_PIN > -1 + #if defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1 const uint8_t digipot_motor_current[] = DIGIPOT_MOTOR_CURRENT; SPI.begin(); @@ -1002,7 +998,7 @@ void digipot_init() //Initialize Digipot Motor Current void digipot_current(uint8_t driver, int current) { - #if DIGIPOTSS_PIN > -1 + #if defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1 const uint8_t digipot_ch[] = DIGIPOT_CHANNELS; digitalPotWrite(digipot_ch[driver], current); #endif @@ -1010,7 +1006,7 @@ void digipot_current(uint8_t driver, int current) void microstep_init() { - #if X_MS1_PIN > -1 + #if defined(X_MS1_PIN) && X_MS1_PIN > -1 const uint8_t microstep_modes[] = MICROSTEP_MODES; pinMode(X_MS2_PIN,OUTPUT); pinMode(Y_MS2_PIN,OUTPUT); diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp index 44c144cde7..ed0a47be2d 100644 --- a/Marlin/temperature.cpp +++ b/Marlin/temperature.cpp @@ -40,10 +40,13 @@ int target_temperature[EXTRUDERS] = { 0 }; int target_temperature_bed = 0; int current_temperature_raw[EXTRUDERS] = { 0 }; -float current_temperature[EXTRUDERS] = { 0 }; +float current_temperature[EXTRUDERS] = { 0.0 }; int current_temperature_bed_raw = 0; -float current_temperature_bed = 0; - +float current_temperature_bed = 0.0; +#ifdef TEMP_SENSOR_1_AS_REDUNDANT + int redundant_temperature_raw = 0; + float redundant_temperature = 0.0; +#endif #ifdef PIDTEMP float Kp=DEFAULT_Kp; float Ki=(DEFAULT_Ki*PID_dT); @@ -99,17 +102,20 @@ static volatile bool temp_meas_ready = false; #ifdef FAN_SOFT_PWM static unsigned char soft_pwm_fan; #endif +#if (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1) || \ + (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1) || \ + (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) + static unsigned long extruder_autofan_last_check; +#endif - - #if EXTRUDERS > 3 -# error Unsupported number of extruders + # error Unsupported number of extruders #elif EXTRUDERS > 2 -# define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1, v2, v3 } + # define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1, v2, v3 } #elif EXTRUDERS > 1 -# define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1, v2 } + # define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1, v2 } #else -# define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1 } + # define ARRAY_BY_EXTRUDERS(v1, v2, v3) { v1 } #endif // Init min and max temp with extreme values to prevent false errors during startup @@ -121,8 +127,14 @@ static int maxttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS( 16383, 16383, 16383 ); #ifdef BED_MAXTEMP static int bed_maxttemp_raw = HEATER_BED_RAW_HI_TEMP; #endif -static void *heater_ttbl_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( (void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE, (void *)HEATER_2_TEMPTABLE ); -static uint8_t heater_ttbllen_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN ); + +#ifdef TEMP_SENSOR_1_AS_REDUNDANT + static void *heater_ttbl_map[2] = {(void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE }; + static uint8_t heater_ttbllen_map[2] = { HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN }; +#else + static void *heater_ttbl_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( (void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE, (void *)HEATER_2_TEMPTABLE ); + static uint8_t heater_ttbllen_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN ); +#endif static float analog2temp(int raw, uint8_t e); static float analog2tempBed(int raw); @@ -154,28 +166,28 @@ void PID_autotune(float temp, int extruder, int ncycles) float Kp, Ki, Kd; float max = 0, min = 10000; - if ((extruder > EXTRUDERS) + if ((extruder > EXTRUDERS) #if (TEMP_BED_PIN <= -1) - ||(extruder < 0) - #endif - ){ - SERIAL_ECHOLN("PID Autotune failed. Bad extruder number."); - return; - } + ||(extruder < 0) + #endif + ){ + SERIAL_ECHOLN("PID Autotune failed. Bad extruder number."); + return; + } SERIAL_ECHOLN("PID Autotune start"); disable_heater(); // switch off all heaters. - if (extruder<0) - { - soft_pwm_bed = (MAX_BED_POWER)/2; - bias = d = (MAX_BED_POWER)/2; - } - else - { - soft_pwm[extruder] = (PID_MAX)/2; - bias = d = (PID_MAX)/2; + if (extruder<0) + { + soft_pwm_bed = (MAX_BED_POWER)/2; + bias = d = (MAX_BED_POWER)/2; + } + else + { + soft_pwm[extruder] = (PID_MAX)/2; + bias = d = (PID_MAX)/2; } @@ -193,10 +205,10 @@ void PID_autotune(float temp, int extruder, int ncycles) if(heating == true && input > temp) { if(millis() - t2 > 5000) { heating=false; - if (extruder<0) - soft_pwm_bed = (bias - d) >> 1; - else - soft_pwm[extruder] = (bias - d) >> 1; + if (extruder<0) + soft_pwm_bed = (bias - d) >> 1; + else + soft_pwm[extruder] = (bias - d) >> 1; t1=millis(); t_high=t1 - t2; max=temp; @@ -247,10 +259,10 @@ void PID_autotune(float temp, int extruder, int ncycles) */ } } - if (extruder<0) - soft_pwm_bed = (bias + d) >> 1; - else - soft_pwm[extruder] = (bias + d) >> 1; + if (extruder<0) + soft_pwm_bed = (bias + d) >> 1; + else + soft_pwm[extruder] = (bias + d) >> 1; cycles++; min=temp; } @@ -261,14 +273,14 @@ void PID_autotune(float temp, int extruder, int ncycles) return; } if(millis() - temp_millis > 2000) { - int p; - if (extruder<0){ - p=soft_pwm_bed; - SERIAL_PROTOCOLPGM("ok B:"); - }else{ - p=soft_pwm[extruder]; - SERIAL_PROTOCOLPGM("ok T:"); - } + int p; + if (extruder<0){ + p=soft_pwm_bed; + SERIAL_PROTOCOLPGM("ok B:"); + }else{ + p=soft_pwm[extruder]; + SERIAL_PROTOCOLPGM("ok T:"); + } SERIAL_PROTOCOL(input); SERIAL_PROTOCOLPGM(" @:"); @@ -306,6 +318,78 @@ int getHeaterPower(int heater) { return soft_pwm[heater]; } +#if (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1) || \ + (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1) || \ + (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) + + #if defined(FAN_PIN) && FAN_PIN > -1 + #if EXTRUDER_0_AUTO_FAN_PIN == FAN_PIN + #error "You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to FAN_PIN" + #endif + #if EXTRUDER_1_AUTO_FAN_PIN == FAN_PIN + #error "You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to FAN_PIN" + #endif + #if EXTRUDER_2_AUTO_FAN_PIN == FAN_PIN + #error "You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to FAN_PIN" + #endif + #endif + +void setExtruderAutoFanState(int pin, bool state) +{ + unsigned char newFanSpeed = (state != 0) ? EXTRUDER_AUTO_FAN_SPEED : 0; + // this idiom allows both digital and PWM fan outputs (see M42 handling). + pinMode(pin, OUTPUT); + digitalWrite(pin, newFanSpeed); + analogWrite(pin, newFanSpeed); +} + +void checkExtruderAutoFans() +{ + uint8_t fanState = 0; + + // which fan pins need to be turned on? + #if defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1 + if (current_temperature[0] > EXTRUDER_AUTO_FAN_TEMPERATURE) + fanState |= 1; + #endif + #if defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1 + if (current_temperature[1] > EXTRUDER_AUTO_FAN_TEMPERATURE) + { + if (EXTRUDER_1_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN) + fanState |= 1; + else + fanState |= 2; + } + #endif + #if defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1 + if (current_temperature[2] > EXTRUDER_AUTO_FAN_TEMPERATURE) + { + if (EXTRUDER_2_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN) + fanState |= 1; + else if (EXTRUDER_2_AUTO_FAN_PIN == EXTRUDER_1_AUTO_FAN_PIN) + fanState |= 2; + else + fanState |= 4; + } + #endif + + // update extruder auto fan states + #if defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1 + setExtruderAutoFanState(EXTRUDER_0_AUTO_FAN_PIN, (fanState & 1) != 0); + #endif + #if defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1 + if (EXTRUDER_1_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN) + setExtruderAutoFanState(EXTRUDER_1_AUTO_FAN_PIN, (fanState & 2) != 0); + #endif + #if defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1 + if (EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN + && EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_1_AUTO_FAN_PIN) + setExtruderAutoFanState(EXTRUDER_2_AUTO_FAN_PIN, (fanState & 4) != 0); + #endif +} + +#endif // any extruder auto fan pins set + void manage_heater() { float pid_input; @@ -396,10 +480,31 @@ void manage_heater() } } #endif - + #ifdef TEMP_SENSOR_1_AS_REDUNDANT + if(fabs(current_temperature[0] - redundant_temperature) > MAX_REDUNDANT_TEMP_SENSOR_DIFF) { + disable_heater(); + if(IsStopped() == false) { + SERIAL_ERROR_START; + SERIAL_ERRORLNPGM("Extruder switched off. Temperature difference between temp sensors is too high !"); + LCD_ALERTMESSAGEPGM("Err: REDUNDANT TEMP ERROR"); + } + #ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE + Stop(); + #endif + } + #endif } // End extruder for loop - + #if (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1) || \ + (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1) || \ + (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) + if(millis() - extruder_autofan_last_check > 2500) // only need to check fan state very infrequently + { + checkExtruderAutoFans(); + extruder_autofan_last_check = millis(); + } + #endif + #ifndef PIDTEMPBED if(millis() - previous_millis_bed_heater < BED_CHECK_INTERVAL) return; @@ -481,7 +586,11 @@ void manage_heater() // Derived from RepRap FiveD extruder::getTemperature() // For hot end temperature measurement. static float analog2temp(int raw, uint8_t e) { +#ifdef TEMP_SENSOR_1_AS_REDUNDANT + if(e > EXTRUDERS) +#else if(e >= EXTRUDERS) +#endif { SERIAL_ERROR_START; SERIAL_ERROR((int)e); @@ -560,7 +669,9 @@ static void updateTemperaturesFromRawValues() current_temperature[e] = analog2temp(current_temperature_raw[e], e); } current_temperature_bed = analog2tempBed(current_temperature_bed_raw); - + #ifdef TEMP_SENSOR_1_AS_REDUNDANT + redundant_temperature = analog2temp(redundant_temperature_raw, 1); + #endif //Reset the watchdog after we know we have a temperature measurement. watchdog_reset(); @@ -571,6 +682,12 @@ static void updateTemperaturesFromRawValues() void tp_init() { +#if (MOTHERBOARD == 80) && ((TEMP_SENSOR_0==-1)||(TEMP_SENSOR_1==-1)||(TEMP_SENSOR_2==-1)||(TEMP_SENSOR_BED==-1)) + //disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector + MCUCR=(1< -1) + #if defined(HEATER_0_PIN) && (HEATER_0_PIN > -1) SET_OUTPUT(HEATER_0_PIN); #endif - #if (HEATER_1_PIN > -1) + #if defined(HEATER_1_PIN) && (HEATER_1_PIN > -1) SET_OUTPUT(HEATER_1_PIN); #endif - #if (HEATER_2_PIN > -1) + #if defined(HEATER_2_PIN) && (HEATER_2_PIN > -1) SET_OUTPUT(HEATER_2_PIN); #endif - #if (HEATER_BED_PIN > -1) + #if defined(HEATER_BED_PIN) && (HEATER_BED_PIN > -1) SET_OUTPUT(HEATER_BED_PIN); #endif - #if (FAN_PIN > -1) + #if defined(FAN_PIN) && (FAN_PIN > -1) SET_OUTPUT(FAN_PIN); #ifdef FAST_PWM_FAN setPwmFrequency(FAN_PIN, 1); // No prescaling. Pwm frequency = F_CPU/256/8 @@ -629,28 +746,28 @@ void tp_init() #ifdef DIDR2 DIDR2 = 0; #endif - #if (TEMP_0_PIN > -1) + #if defined(TEMP_0_PIN) && (TEMP_0_PIN > -1) #if TEMP_0_PIN < 8 DIDR0 |= 1 << TEMP_0_PIN; #else DIDR2 |= 1<<(TEMP_0_PIN - 8); #endif #endif - #if (TEMP_1_PIN > -1) + #if defined(TEMP_1_PIN) && (TEMP_1_PIN > -1) #if TEMP_1_PIN < 8 DIDR0 |= 1< -1) + #if defined(TEMP_2_PIN) && (TEMP_2_PIN > -1) #if TEMP_2_PIN < 8 DIDR0 |= 1 << TEMP_2_PIN; #else - DIDR2 = 1<<(TEMP_2_PIN - 8); + DIDR2 |= 1<<(TEMP_2_PIN - 8); #endif #endif - #if (TEMP_BED_PIN > -1) + #if defined(TEMP_BED_PIN) && (TEMP_BED_PIN > -1) #if TEMP_BED_PIN < 8 DIDR0 |= 1< 1) && defined(HEATER_1_MINTEMP) minttemp[1] = HEATER_1_MINTEMP; - while(analog2temp(minttemp_raw[1], 1) > HEATER_1_MINTEMP) { + while(analog2temp(minttemp_raw[1], 1) < HEATER_1_MINTEMP) { #if HEATER_1_RAW_LO_TEMP < HEATER_1_RAW_HI_TEMP minttemp_raw[1] += OVERSAMPLENR; #else @@ -710,7 +827,7 @@ void tp_init() #if (EXTRUDERS > 2) && defined(HEATER_2_MINTEMP) minttemp[2] = HEATER_2_MINTEMP; - while(analog2temp(minttemp_raw[2], 2) > HEATER_2_MINTEMP) { + while(analog2temp(minttemp_raw[2], 2) < HEATER_2_MINTEMP) { #if HEATER_2_RAW_LO_TEMP < HEATER_2_RAW_HI_TEMP minttemp_raw[2] += OVERSAMPLENR; #else @@ -771,34 +888,34 @@ void disable_heater() for(int i=0;i -1 + #if defined(TEMP_0_PIN) && TEMP_0_PIN > -1 target_temperature[0]=0; soft_pwm[0]=0; - #if HEATER_0_PIN > -1 + #if defined(HEATER_0_PIN) && HEATER_0_PIN > -1 WRITE(HEATER_0_PIN,LOW); #endif #endif - #if TEMP_1_PIN > -1 + #if defined(TEMP_1_PIN) && TEMP_1_PIN > -1 target_temperature[1]=0; soft_pwm[1]=0; - #if HEATER_1_PIN > -1 + #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1 WRITE(HEATER_1_PIN,LOW); #endif #endif - #if TEMP_2_PIN > -1 + #if defined(TEMP_2_PIN) && TEMP_2_PIN > -1 target_temperature[2]=0; soft_pwm[2]=0; - #if HEATER_2_PIN > -1 + #if defined(HEATER_2_PIN) && HEATER_2_PIN > -1 WRITE(HEATER_2_PIN,LOW); #endif #endif - #if TEMP_BED_PIN > -1 + #if defined(TEMP_BED_PIN) && TEMP_BED_PIN > -1 target_temperature_bed=0; soft_pwm_bed=0; - #if HEATER_BED_PIN > -1 + #if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1 WRITE(HEATER_BED_PIN,LOW); #endif #endif @@ -934,7 +1051,7 @@ ISR(TIMER0_COMPB_vect) soft_pwm_2 = soft_pwm[2]; if(soft_pwm_2 > 0) WRITE(HEATER_2_PIN,1); #endif - #if HEATER_BED_PIN > -1 + #if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1 soft_pwm_b = soft_pwm_bed; if(soft_pwm_b > 0) WRITE(HEATER_BED_PIN,1); #endif @@ -950,7 +1067,7 @@ ISR(TIMER0_COMPB_vect) #if EXTRUDERS > 2 if(soft_pwm_2 <= pwm_count) WRITE(HEATER_2_PIN,0); #endif - #if HEATER_BED_PIN > -1 + #if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1 if(soft_pwm_b <= pwm_count) WRITE(HEATER_BED_PIN,0); #endif #ifdef FAN_SOFT_PWM @@ -962,7 +1079,7 @@ ISR(TIMER0_COMPB_vect) switch(temp_state) { case 0: // Prepare TEMP_0 - #if (TEMP_0_PIN > -1) + #if defined(TEMP_0_PIN) && (TEMP_0_PIN > -1) #if TEMP_0_PIN > 7 ADCSRB = 1< -1) + #if defined(TEMP_0_PIN) && (TEMP_0_PIN > -1) raw_temp_0_value += ADC; #endif #ifdef HEATER_0_USES_MAX6675 // TODO remove the blocking @@ -984,7 +1101,7 @@ ISR(TIMER0_COMPB_vect) temp_state = 2; break; case 2: // Prepare TEMP_BED - #if (TEMP_BED_PIN > -1) + #if defined(TEMP_BED_PIN) && (TEMP_BED_PIN > -1) #if TEMP_BED_PIN > 7 ADCSRB = 1< -1) + #if defined(TEMP_BED_PIN) && (TEMP_BED_PIN > -1) raw_temp_bed_value += ADC; #endif temp_state = 4; break; case 4: // Prepare TEMP_1 - #if (TEMP_1_PIN > -1) + #if defined(TEMP_1_PIN) && (TEMP_1_PIN > -1) #if TEMP_1_PIN > 7 ADCSRB = 1< -1) + #if defined(TEMP_1_PIN) && (TEMP_1_PIN > -1) raw_temp_1_value += ADC; #endif temp_state = 6; break; case 6: // Prepare TEMP_2 - #if (TEMP_2_PIN > -1) + #if defined(TEMP_2_PIN) && (TEMP_2_PIN > -1) #if TEMP_2_PIN > 7 ADCSRB = 1< -1) + #if defined(TEMP_2_PIN) && (TEMP_2_PIN > -1) raw_temp_2_value += ADC; #endif temp_state = 0; @@ -1055,6 +1172,9 @@ ISR(TIMER0_COMPB_vect) #if EXTRUDERS > 1 current_temperature_raw[1] = raw_temp_1_value; #endif +#ifdef TEMP_SENSOR_1_AS_REDUNDANT + redundant_temperature_raw = raw_temp_1_value; +#endif #if EXTRUDERS > 2 current_temperature_raw[2] = raw_temp_2_value; #endif diff --git a/Marlin/temperature.h b/Marlin/temperature.h index 7cc62aa529..75ffcd06bf 100644 --- a/Marlin/temperature.h +++ b/Marlin/temperature.h @@ -37,6 +37,9 @@ extern int target_temperature[EXTRUDERS]; extern float current_temperature[EXTRUDERS]; extern int target_temperature_bed; extern float current_temperature_bed; +#ifdef TEMP_SENSOR_1_AS_REDUNDANT + extern float redundant_temperature; +#endif #ifdef PIDTEMP extern float Kp,Ki,Kd,Kc; diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index fe0619fb85..4a9042116f 100644 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -76,7 +76,14 @@ static void menu_action_setting_edit_callback_float51(const char* pstr, float* p static void menu_action_setting_edit_callback_float52(const char* pstr, float* ptr, float minValue, float maxValue, menuFunc_t callbackFunc); static void menu_action_setting_edit_callback_long5(const char* pstr, unsigned long* ptr, unsigned long minValue, unsigned long maxValue, menuFunc_t callbackFunc); -#define ENCODER_STEPS_PER_MENU_ITEM 5 +#define ENCODER_FEEDRATE_DEADZONE 10 + +#if !defined(LCD_I2C_VIKI) + #define ENCODER_STEPS_PER_MENU_ITEM 5 +#else + #define ENCODER_STEPS_PER_MENU_ITEM 2 // VIKI LCD rotary encoder uses a different number of steps per rotation +#endif + /* Helper macros for menus */ #define START_MENU() do { \ @@ -112,14 +119,18 @@ static void menu_action_setting_edit_callback_long5(const char* pstr, unsigned l } } while(0) /** Used variables to keep track of the menu */ +#ifndef REPRAPWORLD_KEYPAD volatile uint8_t buttons;//Contains the bits of the currently pressed buttons. +#else +volatile uint16_t buttons;//Contains the bits of the currently pressed buttons (extended). +#endif uint8_t currentMenuViewOffset; /* scroll offset in the current menu */ uint32_t blocking_enc; uint8_t lastEncoderBits; int8_t encoderDiff; /* encoderDiff is updated from interrupt context and added to encoderPosition every LCD update */ uint32_t encoderPosition; -#if (SDCARDDETECT > -1) +#if (SDCARDDETECT > 0) bool lcd_oldcardstatus; #endif #endif//ULTIPANEL @@ -157,10 +168,34 @@ static void lcd_status_screen() if (LCD_CLICKED) { currentMenu = lcd_main_menu; + encoderPosition = 0; lcd_quick_feedback(); } - feedmultiply += int(encoderPosition); - encoderPosition = 0; + + // Dead zone at 100% feedrate + if (feedmultiply < 100 && (feedmultiply + int(encoderPosition)) > 100 || + feedmultiply > 100 && (feedmultiply + int(encoderPosition)) < 100) + { + encoderPosition = 0; + feedmultiply = 100; + } + + if (feedmultiply == 100 && int(encoderPosition) > ENCODER_FEEDRATE_DEADZONE) + { + feedmultiply += int(encoderPosition) - ENCODER_FEEDRATE_DEADZONE; + encoderPosition = 0; + } + else if (feedmultiply == 100 && int(encoderPosition) < -ENCODER_FEEDRATE_DEADZONE) + { + feedmultiply += int(encoderPosition) + ENCODER_FEEDRATE_DEADZONE; + encoderPosition = 0; + } + else if (feedmultiply != 100) + { + feedmultiply += int(encoderPosition); + encoderPosition = 0; + } + if (feedmultiply < 10) feedmultiply = 10; if (feedmultiply > 999) @@ -221,14 +256,14 @@ static void lcd_main_menu() }else{ MENU_ITEM(submenu, MSG_CARD_MENU, lcd_sdcard_menu); #if SDCARDDETECT < 1 - MENU_ITEM(gcode, MSG_CNG_SDCARD, PSTR("M21")); // SD-card changed by user -#endif + MENU_ITEM(gcode, MSG_CNG_SDCARD, PSTR("M21")); // SD-card changed by user +#endif } }else{ MENU_ITEM(submenu, MSG_NO_CARD, lcd_sdcard_menu); -#if SDCARDDETECT < 1 - MENU_ITEM(gcode, MSG_INIT_SDCARD, PSTR("M21")); // Manually initialize the SD-card via user interface -#endif +#if SDCARDDETECT < 1 + MENU_ITEM(gcode, MSG_INIT_SDCARD, PSTR("M21")); // Manually initialize the SD-card via user interface +#endif } #endif END_MENU(); @@ -251,6 +286,7 @@ void lcd_preheat_pla() setTargetBed(plaPreheatHPBTemp); fanSpeed = plaPreheatFanSpeed; lcd_return_to_status(); + setWatch(); // heater sanity check timer } void lcd_preheat_abs() @@ -261,6 +297,16 @@ void lcd_preheat_abs() setTargetBed(absPreheatHPBTemp); fanSpeed = absPreheatFanSpeed; lcd_return_to_status(); + setWatch(); // heater sanity check timer +} + +static void lcd_cooldown() +{ + setTargetHotend0(0); + setTargetHotend1(0); + setTargetHotend2(0); + setTargetBed(0); + lcd_return_to_status(); } static void lcd_tune_menu() @@ -298,7 +344,7 @@ static void lcd_prepare_menu() //MENU_ITEM(gcode, MSG_SET_ORIGIN, PSTR("G92 X0 Y0 Z0")); MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla); MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs); - MENU_ITEM(gcode, MSG_COOLDOWN, PSTR("M104 S0\nM140 S0")); + MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown); MENU_ITEM(submenu, MSG_MOVE_AXIS, lcd_move_menu); END_MENU(); } @@ -459,10 +505,10 @@ static void lcd_control_menu() static void lcd_control_temperature_menu() { - // set up temp variables - undo the default scaling - raw_Ki = unscalePID_i(Ki); - raw_Kd = unscalePID_d(Kd); - + // set up temp variables - undo the default scaling + raw_Ki = unscalePID_i(Ki); + raw_Kd = unscalePID_d(Kd); + START_MENU(); MENU_ITEM(back, MSG_CONTROL, lcd_control_menu); MENU_ITEM_EDIT(int3, MSG_NOZZLE, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15); @@ -484,7 +530,7 @@ static void lcd_control_temperature_menu() #endif #ifdef PIDTEMP MENU_ITEM_EDIT(float52, MSG_PID_P, &Kp, 1, 9990); - // i is typically a small value so allows values below 1 + // i is typically a small value so allows values below 1 MENU_ITEM_EDIT_CALLBACK(float52, MSG_PID_I, &raw_Ki, 0.01, 9990, copy_and_scalePID_i); MENU_ITEM_EDIT_CALLBACK(float52, MSG_PID_D, &raw_Kd, 1, 9990, copy_and_scalePID_d); # ifdef PID_ADD_EXTRUSION_RATE @@ -687,6 +733,24 @@ menu_edit_type(float, float51, ftostr51, 10) menu_edit_type(float, float52, ftostr52, 100) menu_edit_type(unsigned long, long5, ftostr5, 0.01) +#ifdef REPRAPWORLD_KEYPAD + static void reprapworld_keypad_move_y_down() { + encoderPosition = 1; + move_menu_scale = REPRAPWORLD_KEYPAD_MOVE_STEP; + lcd_move_y(); + } + static void reprapworld_keypad_move_y_up() { + encoderPosition = -1; + move_menu_scale = REPRAPWORLD_KEYPAD_MOVE_STEP; + lcd_move_y(); + } + static void reprapworld_keypad_move_home() { + //enquecommand_P((PSTR("G28"))); // move all axis home + // TODO gregor: move all axis home, i have currently only one axis on my prusa i3 + enquecommand_P((PSTR("G28 Y"))); + } +#endif + /** End of menus **/ static void lcd_quick_feedback() @@ -745,11 +809,20 @@ void lcd_init() #ifdef NEWPANEL pinMode(BTN_EN1,INPUT); pinMode(BTN_EN2,INPUT); - pinMode(BTN_ENC,INPUT); pinMode(SDCARDDETECT,INPUT); WRITE(BTN_EN1,HIGH); WRITE(BTN_EN2,HIGH); + #if BTN_ENC > 0 + pinMode(BTN_ENC,INPUT); WRITE(BTN_ENC,HIGH); + #endif + #ifdef REPRAPWORLD_KEYPAD + pinMode(SHIFT_CLK,OUTPUT); + pinMode(SHIFT_LD,OUTPUT); + pinMode(SHIFT_OUT,INPUT); + WRITE(SHIFT_OUT,HIGH); + WRITE(SHIFT_LD,HIGH); + #endif #else pinMode(SHIFT_CLK,OUTPUT); pinMode(SHIFT_LD,OUTPUT); @@ -759,12 +832,14 @@ void lcd_init() WRITE(SHIFT_LD,HIGH); WRITE(SHIFT_EN,LOW); #endif//!NEWPANEL -#if (SDCARDDETECT > -1) +#if (SDCARDDETECT > 0) WRITE(SDCARDDETECT, HIGH); lcd_oldcardstatus = IS_SD_INSERTED; -#endif//(SDCARDDETECT > -1) +#endif//(SDCARDDETECT > 0) lcd_buttons_update(); +#ifdef ULTIPANEL encoderDiff = 0; +#endif } void lcd_update() @@ -773,7 +848,11 @@ void lcd_update() lcd_buttons_update(); - #if (SDCARDDETECT > -1) + #ifdef LCD_HAS_SLOW_BUTTONS + buttons |= lcd_implementation_read_slow_buttons(); // buttons which take too long to read in interrupt context + #endif + + #if (SDCARDDETECT > 0) if((IS_SD_INSERTED != lcd_oldcardstatus)) { lcdDrawUpdate = 2; @@ -796,6 +875,17 @@ void lcd_update() if (lcd_next_update_millis < millis()) { #ifdef ULTIPANEL + #ifdef REPRAPWORLD_KEYPAD + if (REPRAPWORLD_KEYPAD_MOVE_Y_DOWN) { + reprapworld_keypad_move_y_down(); + } + if (REPRAPWORLD_KEYPAD_MOVE_Y_UP) { + reprapworld_keypad_move_y_up(); + } + if (REPRAPWORLD_KEYPAD_MOVE_HOME) { + reprapworld_keypad_move_home(); + } + #endif if (encoderDiff) { lcdDrawUpdate = 1; @@ -808,21 +898,26 @@ void lcd_update() #endif//ULTIPANEL #ifdef DOGLCD // Changes due to different driver architecture of the DOGM display - blink++; // Variable for fan animation and alive dot - u8g.firstPage(); - do { - u8g.setFont(u8g_font_6x10_marlin); - u8g.setPrintPos(125,0); - if (blink % 2) u8g.setColorIndex(1); else u8g.setColorIndex(0); // Set color for the alive dot - u8g.drawPixel(127,63); // draw alive dot - u8g.setColorIndex(1); // black on white - (*currentMenu)(); - if (!lcdDrawUpdate) break; // Terminate display update, when nothing new to draw. This must be done before the last dogm.next() - } while( u8g.nextPage() ); + blink++; // Variable for fan animation and alive dot + u8g.firstPage(); + do + { + u8g.setFont(u8g_font_6x10_marlin); + u8g.setPrintPos(125,0); + if (blink % 2) u8g.setColorIndex(1); else u8g.setColorIndex(0); // Set color for the alive dot + u8g.drawPixel(127,63); // draw alive dot + u8g.setColorIndex(1); // black on white + (*currentMenu)(); + if (!lcdDrawUpdate) break; // Terminate display update, when nothing new to draw. This must be done before the last dogm.next() + } while( u8g.nextPage() ); #else (*currentMenu)(); #endif +#ifdef LCD_HAS_STATUS_INDICATORS + lcd_implementation_update_indicators(); +#endif + #ifdef ULTIPANEL if(timeoutToStatus < millis() && currentMenu != lcd_status_screen) { @@ -873,8 +968,24 @@ void lcd_buttons_update() uint8_t newbutton=0; if(READ(BTN_EN1)==0) newbutton|=EN_A; if(READ(BTN_EN2)==0) newbutton|=EN_B; + #if BTN_ENC > 0 if((blocking_enc>1; + if(READ(SHIFT_OUT)) + newbutton_reprapworld_keypad|=(1<<7); + WRITE(SHIFT_CLK,HIGH); + WRITE(SHIFT_CLK,LOW); + } + newbutton |= ((~newbutton_reprapworld_keypad) << REPRAPWORLD_BTN_OFFSET); //invert it, because a pressed switch produces a logical 0 + #endif buttons = newbutton; #else //read it from the shift register uint8_t newbutton=0; @@ -930,6 +1041,18 @@ void lcd_buttons_update() } lastEncoderBits = enc; } + +void lcd_buzz(long duration, uint16_t freq) +{ +#ifdef LCD_USE_I2C_BUZZER + lcd.buzz(duration,freq); +#endif +} + +bool lcd_clicked() +{ + return LCD_CLICKED; +} #endif//ULTIPANEL /********************************/ @@ -1131,7 +1254,7 @@ void copy_and_scalePID_i() { Ki = scalePID_i(raw_Ki); updatePID(); -} +} // Callback for after editing PID d value // grab the pid d value out of the temp variable; scale it; then update the PID driver @@ -1139,6 +1262,6 @@ void copy_and_scalePID_d() { Kd = scalePID_d(raw_Kd); updatePID(); -} - +} + #endif //ULTRA_LCD diff --git a/Marlin/ultralcd.h b/Marlin/ultralcd.h index 28de229726..5d3c3c0bee 100644 --- a/Marlin/ultralcd.h +++ b/Marlin/ultralcd.h @@ -22,7 +22,6 @@ #ifdef ULTIPANEL void lcd_buttons_update(); - extern volatile uint8_t buttons; //the last checked buttons in a bit array. #else FORCE_INLINE void lcd_buttons_update() {} #endif @@ -35,25 +34,8 @@ extern int absPreheatHPBTemp; extern int absPreheatFanSpeed; - #ifdef NEWPANEL - #define EN_C (1< -#define LCD_CLASS LiquidCrystal +extern volatile uint16_t buttons; //an extended version of the last checked buttons in a bit array. +#endif + +//////////////////////////////////// +// Setup button and encode mappings for each panel (into 'buttons' variable) +// +// This is just to map common functions (across different panels) onto the same +// macro name. The mapping is independent of whether the button is directly connected or +// via a shift/i2c register. + +#ifdef ULTIPANEL +// All Ultipanels might have an encoder - so this is always be mapped onto first two bits +#define BLEN_B 1 +#define BLEN_A 0 + +#define EN_B (1< -1 + // encoder click is directly connected + #define BLEN_C 2 + #define EN_C (1< -1 + // the pause/stop/restart button is connected to BTN_ENC when used + #define B_ST (EN_C) // Map the pause/stop/resume button into its normalized functional name + #define LCD_CLICKED (buttons&(B_MI|B_RI|B_ST)) // pause/stop button also acts as click until we implement proper pause/stop. + #else + #define LCD_CLICKED (buttons&(B_MI|B_RI)) + #endif + + // I2C buttons take too long to read inside an interrupt context and so we read them during lcd_update + #define LCD_HAS_SLOW_BUTTONS + +#elif defined(LCD_I2C_PANELOLU2) + // encoder click can be read through I2C if not directly connected + #if BTN_ENC <= 0 + #define B_I2C_BTN_OFFSET 3 // (the first three bit positions reserved for EN_A, EN_B, EN_C) + + #define B_MI (PANELOLU2_ENCODER_C< + #include + #include + #define LCD_CLASS LiquidCrystal_I2C + LCD_CLASS lcd(LCD_I2C_ADDRESS,LCD_I2C_PIN_EN,LCD_I2C_PIN_RW,LCD_I2C_PIN_RS,LCD_I2C_PIN_D4,LCD_I2C_PIN_D5,LCD_I2C_PIN_D6,LCD_I2C_PIN_D7); + +#elif defined(LCD_I2C_TYPE_MCP23017) + //for the LED indicators (which maybe mapped to different things in lcd_implementation_update_indicators()) + #define LED_A 0x04 //100 + #define LED_B 0x02 //010 + #define LED_C 0x01 //001 + + #define LCD_HAS_STATUS_INDICATORS + + #include + #include + #define LCD_CLASS LiquidTWI2 + LCD_CLASS lcd(LCD_I2C_ADDRESS); + +#elif defined(LCD_I2C_TYPE_MCP23008) + #include + #include + #define LCD_CLASS LiquidTWI2 + LCD_CLASS lcd(LCD_I2C_ADDRESS); + +#else + // Standard directly connected LCD implementations + #if LANGUAGE_CHOICE == 6 + #include "LiquidCrystalRus.h" + #define LCD_CLASS LiquidCrystalRus + #else + #include + #define LCD_CLASS LiquidCrystal + #endif + LCD_CLASS lcd(LCD_PINS_RS, LCD_PINS_ENABLE, LCD_PINS_D4, LCD_PINS_D5,LCD_PINS_D6,LCD_PINS_D7); //RS,Enable,D4,D5,D6,D7 #endif /* Custom characters defined in the first 8 characters of the LCD */ @@ -25,7 +204,6 @@ #define LCD_STR_CLOCK "\x07" #define LCD_STR_ARROW_RIGHT "\x7E" /* from the default character set */ -LCD_CLASS lcd(LCD_PINS_RS, LCD_PINS_ENABLE, LCD_PINS_D4, LCD_PINS_D5,LCD_PINS_D6,LCD_PINS_D7); //RS,Enable,D4,D5,D6,D7 static void lcd_implementation_init() { byte bedTemp[8] = @@ -111,7 +289,27 @@ static void lcd_implementation_init() B00000, B00000 }; //thanks Sonny Mounicou + +#if defined(LCDI2C_TYPE_PCF8575) lcd.begin(LCD_WIDTH, LCD_HEIGHT); + #ifdef LCD_I2C_PIN_BL + lcd.setBacklightPin(LCD_I2C_PIN_BL,POSITIVE); + lcd.setBacklight(HIGH); + #endif + +#elif defined(LCD_I2C_TYPE_MCP23017) + lcd.setMCPType(LTI_TYPE_MCP23017); + lcd.begin(LCD_WIDTH, LCD_HEIGHT); + lcd.setBacklight(0); //set all the LEDs off to begin with + +#elif defined(LCD_I2C_TYPE_MCP23008) + lcd.setMCPType(LTI_TYPE_MCP23008); + lcd.begin(LCD_WIDTH, LCD_HEIGHT); + +#else + lcd.begin(LCD_WIDTH, LCD_HEIGHT); +#endif + lcd.createChar(LCD_STR_BEDTEMP[0], bedTemp); lcd.createChar(LCD_STR_DEGREE[0], degree); lcd.createChar(LCD_STR_THERMOMETER[0], thermometer); @@ -299,13 +497,13 @@ static void lcd_implementation_drawmenu_generic(uint8_t row, const char* pstr, c char c; //Use all characters in narrow LCDs #if LCD_WIDTH < 20 - uint8_t n = LCD_WIDTH - 1 - 1; + uint8_t n = LCD_WIDTH - 1 - 1; #else - uint8_t n = LCD_WIDTH - 1 - 2; + uint8_t n = LCD_WIDTH - 1 - 2; #endif lcd.setCursor(0, row); lcd.print(pre_char); - while((c = pgm_read_byte(pstr)) != '\0') + while( ((c = pgm_read_byte(pstr)) != '\0') && (n>0) ) { lcd.print(c); pstr++; @@ -321,13 +519,13 @@ static void lcd_implementation_drawmenu_setting_edit_generic(uint8_t row, const char c; //Use all characters in narrow LCDs #if LCD_WIDTH < 20 - uint8_t n = LCD_WIDTH - 1 - 1 - strlen(data); + uint8_t n = LCD_WIDTH - 1 - 1 - strlen(data); #else - uint8_t n = LCD_WIDTH - 1 - 2 - strlen(data); + uint8_t n = LCD_WIDTH - 1 - 2 - strlen(data); #endif lcd.setCursor(0, row); lcd.print(pre_char); - while((c = pgm_read_byte(pstr)) != '\0') + while( ((c = pgm_read_byte(pstr)) != '\0') && (n>0) ) { lcd.print(c); pstr++; @@ -343,13 +541,13 @@ static void lcd_implementation_drawmenu_setting_edit_generic_P(uint8_t row, cons char c; //Use all characters in narrow LCDs #if LCD_WIDTH < 20 - uint8_t n = LCD_WIDTH - 1 - 1 - strlen_P(data); + uint8_t n = LCD_WIDTH - 1 - 1 - strlen_P(data); #else - uint8_t n = LCD_WIDTH - 1 - 2 - strlen_P(data); + uint8_t n = LCD_WIDTH - 1 - 2 - strlen_P(data); #endif lcd.setCursor(0, row); lcd.print(pre_char); - while((c = pgm_read_byte(pstr)) != '\0') + while( ((c = pgm_read_byte(pstr)) != '\0') && (n>0) ) { lcd.print(c); pstr++; @@ -402,9 +600,9 @@ void lcd_implementation_drawedit(const char* pstr, char* value) lcd_printPGM(pstr); lcd.print(':'); #if LCD_WIDTH < 20 - lcd.setCursor(LCD_WIDTH - strlen(value), 1); + lcd.setCursor(LCD_WIDTH - strlen(value), 1); #else - lcd.setCursor(LCD_WIDTH -1 - strlen(value), 1); + lcd.setCursor(LCD_WIDTH -1 - strlen(value), 1); #endif lcd.print(value); } @@ -419,7 +617,7 @@ static void lcd_implementation_drawmenu_sdfile_selected(uint8_t row, const char* filename = longFilename; longFilename[LCD_WIDTH-1] = '\0'; } - while((c = *filename) != '\0') + while( ((c = *filename) != '\0') && (n>0) ) { lcd.print(c); filename++; @@ -439,7 +637,7 @@ static void lcd_implementation_drawmenu_sdfile(uint8_t row, const char* pstr, co filename = longFilename; longFilename[LCD_WIDTH-1] = '\0'; } - while((c = *filename) != '\0') + while( ((c = *filename) != '\0') && (n>0) ) { lcd.print(c); filename++; @@ -460,7 +658,7 @@ static void lcd_implementation_drawmenu_sddirectory_selected(uint8_t row, const filename = longFilename; longFilename[LCD_WIDTH-2] = '\0'; } - while((c = *filename) != '\0') + while( ((c = *filename) != '\0') && (n>0) ) { lcd.print(c); filename++; @@ -481,7 +679,7 @@ static void lcd_implementation_drawmenu_sddirectory(uint8_t row, const char* pst filename = longFilename; longFilename[LCD_WIDTH-2] = '\0'; } - while((c = *filename) != '\0') + while( ((c = *filename) != '\0') && (n>0) ) { lcd.print(c); filename++; @@ -501,15 +699,50 @@ static void lcd_implementation_drawmenu_sddirectory(uint8_t row, const char* pst static void lcd_implementation_quick_feedback() { -#if BEEPER > -1 +#ifdef LCD_USE_I2C_BUZZER + lcd.buzz(60,1000/6); +#elif defined(BEEPER) && BEEPER > -1 SET_OUTPUT(BEEPER); for(int8_t i=0;i<10;i++) { - WRITE(BEEPER,HIGH); - delay(3); - WRITE(BEEPER,LOW); - delay(3); + WRITE(BEEPER,HIGH); + delay(3); + WRITE(BEEPER,LOW); + delay(3); } #endif } + +#ifdef LCD_HAS_STATUS_INDICATORS +static void lcd_implementation_update_indicators() +{ + #if defined(LCD_I2C_PANELOLU2) || defined(LCD_I2C_VIKI) + //set the LEDS - referred to as backlights by the LiquidTWI2 library + static uint8_t ledsprev = 0; + uint8_t leds = 0; + if (target_temperature_bed > 0) leds |= LED_A; + if (target_temperature[0] > 0) leds |= LED_B; + if (fanSpeed) leds |= LED_C; + #if EXTRUDERS > 1 + if (target_temperature[1] > 0) leds |= LED_C; + #endif + if (leds != ledsprev) { + lcd.setBacklight(leds); + ledsprev = leds; + } + #endif +} +#endif + +#ifdef LCD_HAS_SLOW_BUTTONS +static uint8_t lcd_implementation_read_slow_buttons() +{ + #ifdef LCD_I2C_TYPE_MCP23017 + // Reading these buttons this is likely to be too slow to call inside interrupt context + // so they are called during normal lcd_update + return lcd.readButtons() << B_I2C_BTN_OFFSET; + #endif +} +#endif + #endif//ULTRA_LCD_IMPLEMENTATION_HITACHI_HD44780_H diff --git a/Marlin/ultralcd_st7920_u8glib_rrd.h b/Marlin/ultralcd_st7920_u8glib_rrd.h new file mode 100644 index 0000000000..e198a858ac --- /dev/null +++ b/Marlin/ultralcd_st7920_u8glib_rrd.h @@ -0,0 +1,131 @@ +#ifndef ULCDST7920_H +#define ULCDST7920_H + +#include "Marlin.h" + +#ifdef U8GLIB_ST7920 + +//set optimization so ARDUINO optimizes this file +#pragma GCC optimize (3) + +#define ST7920_CLK_PIN LCD_PINS_D4 +#define ST7920_DAT_PIN LCD_PINS_ENABLE +#define ST7920_CS_PIN LCD_PINS_RS + +//#define PAGE_HEIGHT 8 //128 byte frambuffer +//#define PAGE_HEIGHT 16 //256 byte frambuffer +#define PAGE_HEIGHT 32 //512 byte framebuffer + +#define WIDTH 128 +#define HEIGHT 64 + +#include + +static void ST7920_SWSPI_SND_8BIT(uint8_t val) +{ + uint8_t i; + for( i=0; i<8; i++ ) + { + WRITE(ST7920_CLK_PIN,0); + WRITE(ST7920_DAT_PIN,val&0x80); + val<<=1; + WRITE(ST7920_CLK_PIN,1); + } +} + +#define ST7920_CS() {WRITE(ST7920_CS_PIN,1);u8g_10MicroDelay();} +#define ST7920_NCS() {WRITE(ST7920_CS_PIN,0);} +#define ST7920_SET_CMD() {ST7920_SWSPI_SND_8BIT(0xf8);u8g_10MicroDelay();} +#define ST7920_SET_DAT() {ST7920_SWSPI_SND_8BIT(0xfa);u8g_10MicroDelay();} +#define ST7920_WRITE_BYTE(a) {ST7920_SWSPI_SND_8BIT((a)&0xf0);ST7920_SWSPI_SND_8BIT((a)<<4);u8g_10MicroDelay();} +#define ST7920_WRITE_BYTES(p,l) {uint8_t i;for(i=0;idev_mem); + y = pb->p.page_y0; + ptr = (uint8_t*)pb->buf; + + ST7920_CS(); + for( i = 0; i < PAGE_HEIGHT; i ++ ) + { + ST7920_SET_CMD(); + if ( y < 32 ) + { + ST7920_WRITE_BYTE(0x80 | y); //y + ST7920_WRITE_BYTE(0x80); //x=0 + } + else + { + ST7920_WRITE_BYTE(0x80 | (y-32)); //y + ST7920_WRITE_BYTE(0x80 | 8); //x=64 + } + + ST7920_SET_DAT(); + ST7920_WRITE_BYTES(ptr,WIDTH/8); //ptr is incremented inside of macro + y++; + } + ST7920_NCS(); + } + break; + } +#if PAGE_HEIGHT == 8 + return u8g_dev_pb8h1_base_fn(u8g, dev, msg, arg); +#elif PAGE_HEIGHT == 16 + return u8g_dev_pb16h1_base_fn(u8g, dev, msg, arg); +#else + return u8g_dev_pb32h1_base_fn(u8g, dev, msg, arg); +#endif +} + +uint8_t u8g_dev_st7920_128x64_rrd_buf[WIDTH*(PAGE_HEIGHT/8)] U8G_NOCOMMON; +u8g_pb_t u8g_dev_st7920_128x64_rrd_pb = {{PAGE_HEIGHT,HEIGHT,0,0,0},WIDTH,u8g_dev_st7920_128x64_rrd_buf}; +u8g_dev_t u8g_dev_st7920_128x64_rrd_sw_spi = {u8g_dev_rrd_st7920_128x64_fn,&u8g_dev_st7920_128x64_rrd_pb,&u8g_com_null_fn}; + +class U8GLIB_ST7920_128X64_RRD : public U8GLIB +{ + public: + U8GLIB_ST7920_128X64_RRD(uint8_t dummy) : U8GLIB(&u8g_dev_st7920_128x64_rrd_sw_spi) {} +}; + + +#endif //U8GLIB_ST7920 +#endif //ULCDST7920_H diff --git a/README.md b/README.md index 309fdd1d1d..abfb8278ec 100644 --- a/README.md +++ b/README.md @@ -1,12 +1,8 @@ -WARNING: --------- -THIS IS RELEASE CANDIDATE 2 FOR MARLIN 1.0.0 +========================== +Marlin 3D Printer Firmware +========================== -The configuration is now split in two files -Configuration.h for the normal settings -Configuration_adv.h for the advanced settings - -Gen7T is not supported. +[![Flattr this git repo](http://api.flattr.com/button/flattr-badge-large.png)](https://flattr.com/submit/auto?user_id=ErikZalm&url=https://github.com/ErikZalm/Marlin&title=Marlin&language=&tags=github&category=software) Quick Information =================== @@ -46,6 +42,7 @@ Features: * PID tuning * CoreXY kinematics (www.corexy.com/theory.html) * Configurable serial port to support connection of wireless adaptors. +* Automatic operation of extruder/cold-end cooling fans based on nozzle temperature The default baudrate is 250000. This baudrate has less jitter and hence errors than the usual 115200 baud, but is less supported by drivers and host-environments. @@ -129,57 +126,98 @@ necessary for backwards compatibility. An interrupt is used to manage ADC conversions, and enforce checking for critical temperatures. This leads to less blocking in the heater management routine. +Implemented G Codes: +==================== -Non-standard M-Codes, different to an old version of sprinter: -============================================================== -Movement: +* G0 -> G1 +* G1 - Coordinated Movement X Y Z E +* G2 - CW ARC +* G3 - CCW ARC +* G4 - Dwell S or P +* G10 - retract filament according to settings of M207 +* G11 - retract recover filament according to settings of M208 +* G28 - Home all Axis +* G90 - Use Absolute Coordinates +* G91 - Use Relative Coordinates +* G92 - Set current position to cordinates given -* G2 - CW ARC -* G3 - CCW ARC +RepRap M Codes +* M0 - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled) +* M1 - Same as M0 +* M104 - Set extruder target temp +* M105 - Read current temp +* M106 - Fan on +* M107 - Fan off +* M109 - Wait for extruder current temp to reach target temp. +* M114 - Display current position -General: +Custom M Codes +* M17 - Enable/Power all stepper motors +* M18 - Disable all stepper motors; same as M84 +* M20 - List SD card +* M21 - Init SD card +* M22 - Release SD card +* M23 - Select SD file (M23 filename.g) +* M24 - Start/resume SD print +* M25 - Pause SD print +* M26 - Set SD position in bytes (M26 S12345) +* M27 - Report SD print status +* M28 - Start SD write (M28 filename.g) +* M29 - Stop SD write +* M30 - Delete file from SD (M30 filename.g) +* M31 - Output time since last M109 or SD card start to serial +* M42 - Change pin status via gcode Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used. +* M80 - Turn on Power Supply +* M81 - Turn off Power Supply +* M82 - Set E codes absolute (default) +* M83 - Set E codes relative while in Absolute Coordinates (G90) mode +* M84 - Disable steppers until next move, or use S to specify an inactivity timeout, after which the steppers will be disabled. S0 to disable the timeout. +* M85 - Set inactivity shutdown timer with parameter S. To disable set zero (default) +* M92 - Set axis_steps_per_unit - same syntax as G92 +* M114 - Output current position to serial port +* M115 - Capabilities string +* M117 - display message +* M119 - Output Endstop status to serial port +* M126 - Solenoid Air Valve Open (BariCUDA support by jmil) +* M127 - Solenoid Air Valve Closed (BariCUDA vent to atmospheric pressure by jmil) +* M128 - EtoP Open (BariCUDA EtoP = electricity to air pressure transducer by jmil) +* M129 - EtoP Closed (BariCUDA EtoP = electricity to air pressure transducer by jmil) +* M140 - Set bed target temp +* M190 - Wait for bed current temp to reach target temp. +* M200 - Set filament diameter +* M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000) +* M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!! +* M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec +* M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate +* M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk +* M206 - set additional homeing offset +* M207 - set retract length S[positive mm] F[feedrate mm/sec] Z[additional zlift/hop] +* M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/sec] +* M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction. +* M218 - set hotend offset (in mm): T X Y +* M220 S- set speed factor override percentage +* M221 S- set extrude factor override percentage +* M240 - Trigger a camera to take a photograph +* M280 - set servo position absolute. P: servo index, S: angle or microseconds +* M300 - Play beepsound S P +* M301 - Set PID parameters P I and D +* M302 - Allow cold extrudes +* M303 - PID relay autotune S sets the target temperature. (default target temperature = 150C) +* M304 - Set bed PID parameters P I and D +* M400 - Finish all moves +* M500 - stores paramters in EEPROM +* M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +* M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +* M503 - print the current settings (from memory not from eeprom) +* M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) +* M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] +* M907 - Set digital trimpot motor current using axis codes. +* M908 - Control digital trimpot directly. +* M350 - Set microstepping mode. +* M351 - Toggle MS1 MS2 pins directly. +* M928 - Start SD logging (M928 filename.g) - ended by M29 +* M999 - Restart after being stopped by error -* M17 - Enable/Power all stepper motors. Compatibility to ReplicatorG. -* M18 - Disable all stepper motors; same as M84.Compatibility to ReplicatorG. -* M30 - Print time since last M109 or SD card start to serial -* M42 - Change pin status via gcode -* M80 - Turn on Power Supply -* M81 - Turn off Power Supply -* M114 - Output current position to serial port -* M119 - Output Endstop status to serial port - -Movement variables: - -* M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!! -* M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec -* M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate -* M206 - set home offsets. This sets the X,Y,Z coordinates of the endstops (and is added to the {X,Y,Z}_HOME_POS configuration options (and is also added to the coordinates, if any, provided to G82, as with earlier firmware) -* M220 - set build speed mulitplying S:factor in percent ; aka "realtime tuneing in the gcode". So you can slow down if you have islands in one height-range, and speed up otherwise. -* M221 - set the extrude multiplying S:factor in percent -* M400 - Finish all buffered moves. - -Temperature variables: -* M301 - Set PID parameters P I and D -* M302 - Allow cold extrudes -* M303 - PID relay autotune S sets the target temperature. (default target temperature = 150C) - -Advance: - -* M200 - Set filament diameter for advance -* M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk - -EEPROM: - -* M500 - stores paramters in EEPROM. This parameters are stored: axis_steps_per_unit, max_feedrate, max_acceleration ,acceleration,retract_acceleration, - minimumfeedrate,mintravelfeedrate,minsegmenttime, jerk velocities, PID -* M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). -* M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. -* M503 - print the current settings (from memory not from eeprom) - -MISC: - -* M240 - Trigger a camera to take a photograph -* M999 - Restart after being stopped by error Configuring and compilation: ============================ @@ -190,12 +228,7 @@ Install the arduino software IDE/toolset v23 (Some configurations also work with For gen6/gen7 and sanguinololu the Sanguino directory in the Marlin dir needs to be copied to the arduino environment. copy ArduinoAddons\Arduino_x.x.x\sanguino \hardware\Sanguino -Install Ultimaker's RepG 25 build - http://software.ultimaker.com -For SD handling and as better substitute (apart from stl manipulation) download -the very nice Kliment's printrun/pronterface https://github.com/kliment/Printrun - -Copy the Ultimaker Marlin firmware +Copy the Marlin firmware https://github.com/ErikZalm/Marlin/tree/Marlin_v1 (Use the download button) @@ -209,15 +242,8 @@ Click the Verify/Compile button Click the Upload button If all goes well the firmware is uploading -Start Ultimaker's Custom RepG 25 -Make sure Show Experimental Profiles is enabled in Preferences -Select Sprinter as the Driver - -Press the Connect button. - -KNOWN ISSUES: RepG will display: Unknown: marlin x.y.z - That's ok. Enjoy Silky Smooth Printing. +