diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h index 1430375482..ec85970ac4 100644 --- a/Marlin/src/core/boards.h +++ b/Marlin/src/core/boards.h @@ -352,19 +352,20 @@ #define BOARD_CREALITY_V431_D 4049 // Creality v4.3.1d (STM32F103RC / STM32F103RE) #define BOARD_CREALITY_V452 4050 // Creality v4.5.2 (STM32F103RC / STM32F103RE) #define BOARD_CREALITY_V453 4051 // Creality v4.5.3 (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V24S1 4052 // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender 7 -#define BOARD_CREALITY_V24S1_301 4053 // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) as found in the Ender 3 S1 -#define BOARD_TRIGORILLA_PRO 4054 // Trigorilla Pro (STM32F103ZE) -#define BOARD_FLY_MINI 4055 // FLYmaker FLY MINI (STM32F103RC) -#define BOARD_FLSUN_HISPEED 4056 // FLSUN HiSpeedV1 (STM32F103VE) -#define BOARD_BEAST 4057 // STM32F103RE Libmaple-based controller -#define BOARD_MINGDA_MPX_ARM_MINI 4058 // STM32F103ZE Mingda MD-16 -#define BOARD_GTM32_PRO_VD 4059 // STM32F103VE controller -#define BOARD_ZONESTAR_ZM3E2 4060 // Zonestar ZM3E2 (STM32F103RC) -#define BOARD_ZONESTAR_ZM3E4 4061 // Zonestar ZM3E4 V1 (STM32F103VC) -#define BOARD_ZONESTAR_ZM3E4V2 4062 // Zonestar ZM3E4 V2 (STM32F103VC) -#define BOARD_ERYONE_ERY32_MINI 4063 // Eryone Ery32 mini (STM32F103VE) -#define BOARD_PANDA_PI_V29 4064 // Panda Pi V2.9 - Standalone (STM32F103RC) +#define BOARD_CREALITY_V24S1 4052 // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender-7 +#define BOARD_CREALITY_V24S1_301 4053 // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) v301 as found in the Ender-3 S1 +#define BOARD_CREALITY_V25S1 4054 // Creality v2.5.S1 (STM32F103RE) as found in the CR-10 Smart Pro +#define BOARD_TRIGORILLA_PRO 4055 // Trigorilla Pro (STM32F103ZE) +#define BOARD_FLY_MINI 4056 // FLYmaker FLY MINI (STM32F103RC) +#define BOARD_FLSUN_HISPEED 4057 // FLSUN HiSpeedV1 (STM32F103VE) +#define BOARD_BEAST 4058 // STM32F103RE Libmaple-based controller +#define BOARD_MINGDA_MPX_ARM_MINI 4059 // STM32F103ZE Mingda MD-16 +#define BOARD_GTM32_PRO_VD 4060 // STM32F103VE controller +#define BOARD_ZONESTAR_ZM3E2 4061 // Zonestar ZM3E2 (STM32F103RC) +#define BOARD_ZONESTAR_ZM3E4 4062 // Zonestar ZM3E4 V1 (STM32F103VC) +#define BOARD_ZONESTAR_ZM3E4V2 4063 // Zonestar ZM3E4 V2 (STM32F103VC) +#define BOARD_ERYONE_ERY32_MINI 4064 // Eryone Ery32 mini (STM32F103VE) +#define BOARD_PANDA_PI_V29 4065 // Panda Pi V2.9 - Standalone (STM32F103RC) // // ARM Cortex-M4F diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index 01e5ee41e3..aecf17284a 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -583,6 +583,8 @@ #include "stm32f1/pins_CREALITY_V24S1.h" // STM32F1 env:STM32F103RE_creality env:STM32F103RE_creality_xfer env:STM32F103RC_creality env:STM32F103RC_creality_xfer env:STM32F103RE_creality_maple #elif MB(CREALITY_V24S1_301) #include "stm32f1/pins_CREALITY_V24S1_301.h" // STM32F1 env:STM32F103RE_creality env:STM32F103RE_creality_xfer env:STM32F103RC_creality env:STM32F103RC_creality_xfer env:STM32F103RE_creality_maple +#elif MB(CREALITY_V25S1) + #include "stm32f1/pins_CREALITY_V25S1.h" // STM32F1 env:STM32F103RE_creality_smartPro env:STM32F103RE_creality_smartPro_maple #elif MB(TRIGORILLA_PRO) #include "stm32f1/pins_TRIGORILLA_PRO.h" // STM32F1 env:trigorilla_pro env:trigorilla_pro_maple #elif MB(FLY_MINI) diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V24S1.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V24S1.h index 9d7e0f695b..0d2ad835d3 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V24S1.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V24S1.h @@ -22,7 +22,7 @@ #pragma once /** - * Creality v2.4.S1 (STM32F103RE / STM32F103RC) v101 as found in the Ender 7 board pin assignments + * Creality v2.4.S1 (STM32F103RE / STM32F103RC) v101 as found in the Ender 7 */ #define BOARD_INFO_NAME "Creality v2.4.S1 V101" diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V25S1.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V25S1.h new file mode 100644 index 0000000000..0425a45d1d --- /dev/null +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V25S1.h @@ -0,0 +1,152 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Creality v2.5.S1 (STM32F103RE / STM32F103RC) as found in the CR-10 Smart Pro + */ + +#include "env_validate.h" + +#if HAS_MULTI_HOTEND || E_STEPPERS > 1 + #error "Creality V2.5.S1 only supports one hotend / E-stepper. Comment out this line to continue." +#endif + +#define BOARD_INFO_NAME "Creality v2.5.S1" +#define DEFAULT_MACHINE_NAME "Creality3D" + +// +// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role +// +#define DISABLE_DEBUG + +// +// EEPROM +// +#if NO_EEPROM_SELECTED + #define IIC_BL24CXX_EEPROM // EEPROM on I2C-0 + //#define SDCARD_EEPROM_EMULATION + //#define FLASH_EEPROM_EMULATION +#endif + +#if ENABLED(IIC_BL24CXX_EEPROM) + #define IIC_EEPROM_SDA PA11 + #define IIC_EEPROM_SCL PA12 + #define MARLIN_EEPROM_SIZE 0x800 // 2K (24C16) +#elif EITHER(SDCARD_EEPROM_EMULATION, FLASH_EEPROM_EMULATION) + #define MARLIN_EEPROM_SIZE 0x800 // 2K +#endif + +// +// Limit Switches +// +#define X_STOP_PIN PC4 +#define Y_STOP_PIN PC5 + +#if ENABLED(BLTOUCH) + #define Z_STOP_PIN -1 + #define SERVO0_PIN PC14 // BLTouch OUT PIN + #ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN PC15 // BLTouch IN PIN + #endif +#else + #define Z_STOP_PIN PC15 + #if ENABLED(PROBE_ACTIVATION_SWITCH) + #define PROBE_TARE_PIN PC14 + #define PROBE_ACTIVATION_SWITCH_PIN PB2 + #endif +#endif + +// +// Filament Runout Sensor +// +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define FIL_RUNOUT_PIN PA15 // "Pulled-high" +#endif + +// +// Steppers +// +#define X_STEP_PIN PB8 +#define X_DIR_PIN PB7 +#define X_ENABLE_PIN PC3 + +#define Y_STEP_PIN PB6 +#define Y_DIR_PIN PB5 +#define Y_ENABLE_PIN X_ENABLE_PIN + +#define Z_STEP_PIN PB4 +#define Z_DIR_PIN PB3 +#define Z_ENABLE_PIN X_ENABLE_PIN + +#define E0_STEP_PIN PC2 +#define E0_DIR_PIN PB9 +#define E0_ENABLE_PIN X_ENABLE_PIN + +// +// Temperature Sensors +// +#define TEMP_0_PIN PB1 // TH1 +#define TEMP_BED_PIN PB0 // TB1 + +// +// Heaters / Fans +// +#define HEATER_0_PIN PB14 // HEATER1 +#define HEATER_BED_PIN PB13 // HOT BED + +#define FAN_PIN PB15 // FAN +#ifndef E0_AUTO_FAN_PIN + #define E0_AUTO_FAN_PIN PC13 // FAN +#endif +#define FAN_SOFT_PWM_REQUIRED + +// +// SD Card +// +#define SD_DETECT_PIN PC7 +#define SDCARD_CONNECTION ONBOARD +#define ON_BOARD_SPI_DEVICE 1 +#define ONBOARD_SD_CS_PIN PC12 // SDSS +#define SDIO_SUPPORT +#define NO_SD_HOST_DRIVE // This board's SD is only seen by the printer + +// +// Misc. Functions +// +#define CASE_LIGHT_PIN PA7 + +// +// Suicide Power +// +#define PS_ON_PIN PA0 +#define MOTOR_CIRCUIT_PIN PA1 + +// +// Motor Protect +// +#define MOTOR_PROTECT_PIN PC0 + +// +// WiFi Reset +// +#define RESET_WIFI_PIN PB12 diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h index b2534beab6..1b95032b36 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h @@ -40,6 +40,11 @@ #define BOARD_NO_NATIVE_USB +// +// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role +// +#define DISABLE_DEBUG + // // EEPROM // @@ -122,11 +127,6 @@ #endif #define E0_ENABLE_PIN X_ENABLE_PIN -// -// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role -// -#define DISABLE_DEBUG - // // Temperature Sensors // diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h index 87101ecccd..1c9a0a8f99 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h @@ -40,34 +40,24 @@ #define BOARD_NO_NATIVE_USB +// +// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role +// +#define DISABLE_DEBUG + // // EEPROM // #if NO_EEPROM_SELECTED - // FLASH - //#define FLASH_EEPROM_EMULATION - - // I2C - #define IIC_BL24CXX_EEPROM // EEPROM on I2C-0 used only for display settings - #if ENABLED(IIC_BL24CXX_EEPROM) - #define IIC_EEPROM_SDA PA11 - #define IIC_EEPROM_SCL PA12 - #define MARLIN_EEPROM_SIZE 0x800 // 2K (24C16) - #else - #define SDCARD_EEPROM_EMULATION // SD EEPROM until all EEPROM is BL24CXX - #define MARLIN_EEPROM_SIZE 0x800 // 2K - #endif - - // SPI - //#define SPI_EEPROM // EEPROM on SPI-0 - //#define SPI_CHAN_EEPROM1 ? - //#define SPI_EEPROM1_CS_PIN ? - - // 2K EEPROM - //#define SPI_EEPROM2_CS_PIN ? - - // 32Mb FLASH - //#define SPI_FLASH_CS_PIN ? + #define IIC_BL24CXX_EEPROM // EEPROM on I2C-0 +#endif +#if ENABLED(IIC_BL24CXX_EEPROM) + #define IIC_EEPROM_SDA PA11 + #define IIC_EEPROM_SCL PA12 + #define MARLIN_EEPROM_SIZE 0x800 // 2K (24C16) +#else + #define SDCARD_EEPROM_EMULATION // SD EEPROM until all EEPROM is BL24CXX + #define MARLIN_EEPROM_SIZE 0x800 // 2K #endif // @@ -82,7 +72,9 @@ #define Y_STOP_PIN PA7 #define Z_STOP_PIN PA5 -#define Z_MIN_PROBE_PIN PA5 // BLTouch IN +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN PA5 // BLTouch IN +#endif // // Filament Runout Sensor @@ -94,42 +86,37 @@ // // Steppers // -#define X_ENABLE_PIN PC3 #ifndef X_STEP_PIN #define X_STEP_PIN PC2 #endif #ifndef X_DIR_PIN #define X_DIR_PIN PB9 #endif +#define X_ENABLE_PIN PC3 -#define Y_ENABLE_PIN PC3 #ifndef Y_STEP_PIN #define Y_STEP_PIN PB8 #endif #ifndef Y_DIR_PIN #define Y_DIR_PIN PB7 #endif +#define Y_ENABLE_PIN X_ENABLE_PIN -#define Z_ENABLE_PIN PC3 #ifndef Z_STEP_PIN #define Z_STEP_PIN PB6 #endif #ifndef Z_DIR_PIN #define Z_DIR_PIN PB5 #endif +#define Z_ENABLE_PIN X_ENABLE_PIN -#define E0_ENABLE_PIN PC3 #ifndef E0_STEP_PIN #define E0_STEP_PIN PB4 #endif #ifndef E0_DIR_PIN #define E0_DIR_PIN PB3 #endif - -// -// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role -// -#define DISABLE_DEBUG +#define E0_ENABLE_PIN X_ENABLE_PIN // // Temperature Sensors diff --git a/buildroot/share/PlatformIO/ldscripts/crealityPro.ld b/buildroot/share/PlatformIO/ldscripts/crealityPro.ld new file mode 100644 index 0000000000..442c5c7507 --- /dev/null +++ b/buildroot/share/PlatformIO/ldscripts/crealityPro.ld @@ -0,0 +1,14 @@ +MEMORY +{ + ram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K - 40 + rom (rx) : ORIGIN = 0x08010000, LENGTH = 512K - 64K +} + +/* Provide memory region aliases for common.inc */ +REGION_ALIAS("REGION_TEXT", rom); +REGION_ALIAS("REGION_DATA", ram); +REGION_ALIAS("REGION_BSS", ram); +REGION_ALIAS("REGION_RODATA", rom); + +/* Let common.inc handle the real work. */ +INCLUDE common.inc \ No newline at end of file diff --git a/ini/stm32f1-maple.ini b/ini/stm32f1-maple.ini index 9ea848f1b6..f0a0f93758 100644 --- a/ini/stm32f1-maple.ini +++ b/ini/stm32f1-maple.ini @@ -147,6 +147,14 @@ extra_scripts = ${common_stm32f1.extra_scripts} debug_tool = jlink upload_protocol = jlink +# +# Creality (STM32F103RET6) +# +[env:STM32F103RE_creality_smartPro_maple] +extends = env:STM32F103RE_creality_maple +board_build.address = 0x08010000 +board_build.ldscript = crealityPro.ld + # # BigTree SKR Mini E3 V2.0 & DIP / SKR CR6 (STM32F103RET6 ARM Cortex-M3) # diff --git a/ini/stm32f1.ini b/ini/stm32f1.ini index 9002f81a81..464048adcb 100644 --- a/ini/stm32f1.ini +++ b/ini/stm32f1.ini @@ -153,6 +153,11 @@ board = genericSTM32F103RE extends = STM32F103Rx_creality_xfer board = genericSTM32F103RE +[env:STM32F103RE_creality_smartPro] +extends = STM32F103Rx_creality +board_build.offset = 0x10000 +board_upload.offset_address = 0x08010000 + # # Creality 256K (STM32F103RC) #