Add Filament Change accelerations to example configs
This commit is contained in:
Scott Lahteine
parent
dcb1f1f452
commit
71d3523254
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 1 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
//#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 1 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
//#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 4 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 420 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 8 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 4 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 420 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 8 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 120 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 120 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,38 +900,44 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 4 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 41 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 430 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 41 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 430 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 20 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 4 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 41 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 430 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 41 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 430 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 20 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 4 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 0 // (mm) An unretract is done, then this length is purged.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 4 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 0 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 4 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 420 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 8 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 4 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 420 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 8 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 120 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 120 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,38 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -901,39 +901,44 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -908,39 +908,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -913,39 +913,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 5 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 600 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 100 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 5 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 600 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 100 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -902,39 +902,44 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -902,39 +902,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -902,39 +902,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -902,39 +902,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -902,39 +902,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -902,39 +902,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -907,39 +907,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -902,39 +902,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -900,39 +900,45 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -901,39 +901,44 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
Loading…
Reference in a new issue