Balance CI tests (#20485)

Marlin/src/inc/SanityCheck.h

@@ -1916,7 +1916,7 @@ static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal
 /**
  * LED Backlight Timeout
  */
-#if defined(LED_BACKLIGHT_TIMEOUT) && !(ENABLED(PSU_CONTROL) && EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1))
+#if defined(LED_BACKLIGHT_TIMEOUT) && !(ENABLED(PSU_CONTROL) && ANY(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1, FYSETC_242_OLED_12864))
   #error "LED_BACKLIGHT_TIMEOUT requires a FYSETC Mini Panel and a Power Switch."
 #endif
 

Marlin/src/pins/ramps/pins_FYSETC_F6_13.h

@@ -226,7 +226,7 @@
   #define DOGLCD_SCK                          17
   #define DOGLCD_A0                  LCD_PINS_DC
 
-  #define KILL_PIN                            -1  // NC
+  #undef KILL_PIN
   #define NEOPIXEL_PIN                        27
 
 #else
@@ -243,7 +243,6 @@
       #define LCD_BACKLIGHT_PIN               27
     #endif
 
-    #define KILL_PIN                          41
     #define LCD_RESET_PIN                     23  // Must be high or open for LCD to operate normally.
                                   // Seems to work best if left open.
 

buildroot/tests/FYSETC_F6_13-tests

@@ -14,5 +14,66 @@ opt_set MOTHERBOARD BOARD_FYSETC_F6_13
 opt_enable DGUS_LCD_UI_FYSETC
 exec_test $1 $2 "FYSETC F6 1.3 with DGUS" "$3"
 
+#
+# Delta Config (generic) + UBL + ALLEN_KEY + EEPROM_SETTINGS + OLED_PANEL_TINYBOY2
+#
+use_example_configs delta/generic
+opt_set MOTHERBOARD BOARD_FYSETC_F6_13
+opt_enable RESTORE_LEVELING_AFTER_G28 EEPROM_SETTINGS EEPROM_CHITCHAT \
+           Z_PROBE_ALLEN_KEY AUTO_BED_LEVELING_UBL \
+           OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY DELTA_CALIBRATION_MENU
+opt_set LCD_LANGUAGE ko_KR
+opt_set X_DRIVER_TYPE L6470
+opt_set Y_DRIVER_TYPE L6470
+opt_set Z_DRIVER_TYPE L6470
+opt_add L6470_CHAIN_SCK_PIN  53
+opt_add L6470_CHAIN_MISO_PIN 49
+opt_add L6470_CHAIN_MOSI_PIN 40
+opt_add L6470_CHAIN_SS_PIN   42
+opt_add "ENABLE_RESET_L64XX_CHIPS(V) NOOP"
+exec_test $1 $2 "DELTA, RAMPS, L6470, UBL, Allen Key, EEPROM, OLED_PANEL_TINYBOY2..." "$3"
+
+#
+# Test mixed TMC config
+#
+restore_configs
+opt_set MOTHERBOARD BOARD_FYSETC_F6_13
+opt_set LCD_LANGUAGE vi
+opt_set X_DRIVER_TYPE TMC2160
+opt_set Y_DRIVER_TYPE TMC5160
+opt_set Z_DRIVER_TYPE TMC2208_STANDALONE
+opt_set E0_DRIVER_TYPE TMC2130
+opt_set X_MIN_ENDSTOP_INVERTING true
+opt_set Y_MIN_ENDSTOP_INVERTING true
+opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \
+           MARLIN_BRICKOUT MARLIN_INVADERS MARLIN_SNAKE \
+           MONITOR_DRIVER_STATUS STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD \
+           USE_ZMIN_PLUG SENSORLESS_HOMING TMC_DEBUG M114_DETAIL
+exec_test $1 $2 "RAMPS | Mixed TMC | Sensorless | RRDFGSC | Games" "$3"
+
+#
+# Delta Config (FLSUN AC because it's complex)
+#
+use_example_configs delta/FLSUN/auto_calibrate
+opt_set MOTHERBOARD BOARD_FYSETC_F6_13
+exec_test $1 $2 "RAMPS 1.3 | DELTA | FLSUN AC Config" "$3"
+
+#
+# SCARA with Mixed TMC
+#
+use_example_configs SCARA/Morgan
+opt_set MOTHERBOARD BOARD_FYSETC_F6_13
+opt_set LCD_LANGUAGE es
+opt_enable USE_ZMIN_PLUG FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR PAUSE_BEFORE_DEPLOY_STOW \
+           FYSETC_242_OLED_12864 EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL Z_SAFE_HOMING \
+           STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD SENSORLESS_HOMING SQUARE_WAVE_STEPPING
+opt_set X_MAX_ENDSTOP_INVERTING false
+opt_set X_DRIVER_TYPE TMC2209
+opt_set Y_DRIVER_TYPE TMC2130
+opt_set Z_DRIVER_TYPE TMC2130_STANDALONE
+opt_set E0_DRIVER_TYPE TMC2660
+opt_add X_HARDWARE_SERIAL Serial2
+exec_test $1 $2 "FYSETC_F6 | SCARA | Mixed TMC | EEPROM" "$3"
+
 # clean up
 restore_configs

buildroot/tests/LPC1769-tests

@@ -12,22 +12,6 @@ set -e
 use_example_configs Azteeg/X5GT
 exec_test $1 $2 "Azteeg X5GT Example Configuration" "$3"
 
-restore_configs
-opt_set MOTHERBOARD BOARD_SMOOTHIEBOARD
-opt_set EXTRUDERS 2
-opt_set TEMP_SENSOR_1 -1
-opt_set TEMP_SENSOR_BED 5
-opt_enable VIKI2 SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
-           FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
-           LEVEL_BED_CORNERS LEVEL_CORNERS_USE_PROBE LEVEL_CORNERS_VERIFY_RAISED \
-           BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \
-           PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
-           Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \
-           LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES SDCARD_SORT_ALPHA EMERGENCY_PARSER
-opt_disable SD_PROCEDURE_DEPTH
-opt_set GRID_MAX_POINTS_X 16
-exec_test $1 $2 "Smoothieboard with many features" "$3"
-
 restore_configs
 opt_set MOTHERBOARD BOARD_SMOOTHIEBOARD
 opt_set EXTRUDERS 2
@@ -35,12 +19,12 @@ opt_set TEMP_SENSOR_1 -1
 opt_set TEMP_SENSOR_BED 5
 opt_enable TFTGLCD_PANEL_SPI SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
            FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
-           BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET \
+           BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET LEVEL_CORNERS_USE_PROBE LEVEL_CORNERS_VERIFY_RAISED \
            PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
            Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \
            LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES SDCARD_SORT_ALPHA EMERGENCY_PARSER
 opt_set GRID_MAX_POINTS_X 16
-exec_test $1 $2 "Smoothieboard with TFTGLCD_PANEL_SPI" "$3"
+exec_test $1 $2 "Smoothieboard with TFTGLCD_PANEL_SPI and many features" "$3"
 
 #restore_configs
 #opt_set MOTHERBOARD BOARD_AZTEEG_X5_MINI_WIFI

buildroot/tests/mega2560-tests

@@ -60,21 +60,6 @@ opt_disable SEGMENT_LEVELED_MOVES
 opt_enable BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET DOUBLECLICK_FOR_Z_BABYSTEPPING BABYSTEP_HOTEND_Z_OFFSET BABYSTEP_DISPLAY_TOTAL M114_DETAIL
 exec_test $1 $2 "Azteeg X3 Pro | EXTRUDERS 5 | RRDFGSC | UBL | LIN_ADVANCE | Sled Probe | Skew | JP-Kana | Babystep offsets ..." "$3"
 
-#
-# Test a Servo Probe
-# ...with AUTO_BED_LEVELING_3POINT, DEBUG_LEVELING_FEATURE, EEPROM_SETTINGS, EEPROM_CHITCHAT, EXTENDED_CAPABILITIES_REPORT, and AUTO_REPORT_TEMPERATURES
-#
-restore_configs
-opt_set LCD_LANGUAGE zh_CN
-opt_set MMU_MODEL PRUSA_MMU2S
-opt_set EXTRUDERS 5
-opt_set NUM_SERVOS 1
-opt_enable ZONESTAR_LCD Z_PROBE_SERVO_NR Z_SERVO_ANGLES DEACTIVATE_SERVOS_AFTER_MOVE BOOT_MARLIN_LOGO_ANIMATED \
-           AUTO_BED_LEVELING_3POINT DEBUG_LEVELING_FEATURE EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL \
-           NO_VOLUMETRICS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES AUTOTEMP G38_PROBE_TARGET JOYSTICK \
-           MMU2_MENUS DIRECT_STEPPING DETECT_BROKEN_ENDSTOP \
-           FILAMENT_RUNOUT_SENSOR NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE Z_SAFE_HOMING
-exec_test $1 $2 "RAMPS | ZONESTAR + Chinese | MMU2S | Servo | 3-Point + Debug | G38 ..." "$3"
 
 #
 # 5 runout sensors with distinct states
@@ -100,27 +85,6 @@ opt_set FIL_RUNOUT4_PIN 46
 opt_set FIL_RUNOUT5_PIN 47
 exec_test $1 $2 "Multiple runout sensors (x5) | Distinct runout states" "$3"
 
-#
-# Test MINIRAMBO with PWM_MOTOR_CURRENT and many features
-#
-restore_configs
-opt_set MOTHERBOARD BOARD_MEGACONTROLLER
-opt_set LCD_LANGUAGE de
-opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT \
-           MINIPANEL SDSUPPORT PCA9632 LCD_INFO_MENU SOUND_MENU_ITEM GCODE_REPEAT_MARKERS \
-           AUTO_BED_LEVELING_BILINEAR PROBE_MANUALLY LCD_BED_LEVELING G26_MESH_VALIDATION MESH_EDIT_MENU \
-           LIN_ADVANCE EXTRA_LIN_ADVANCE_K \
-           INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT EXPERIMENTAL_I2CBUS M100_FREE_MEMORY_WATCHER \
-           NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE \
-           ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE ADVANCED_PAUSE_CONTINUOUS_PURGE FILAMENT_LOAD_UNLOAD_GCODES \
-           PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 M114_DETAIL \
-           USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE
-opt_set CONTROLLERFAN_SPEED_IDLE 128
-opt_add M100_FREE_MEMORY_DUMPER
-opt_add M100_FREE_MEMORY_CORRUPTOR
-opt_set PWM_MOTOR_CURRENT "{ 1300, 1300, 1250 }"
-opt_set I2C_SLAVE_ADDRESS 63
-exec_test $1 $2 "MEGACONTROLLER | Minipanel | M100 | PWM_MOTOR_CURRENT | PRINTCOUNTER | Advanced Pause ..." "$3"
 
 #
 # Mixing Extruder with 5 steppers, Greek
@@ -150,31 +114,6 @@ exec_test $1 $2 "Azteeg X3 | Mixing Extruder (x5) | Gradient Mix | Greek" "$3"
 #opt_enable COREXY
 #exec_test $1 $2 "Stuff" "$3"
 
-#
-# Test many less common options
-#
-restore_configs
-opt_set MOTHERBOARD BOARD_MIGHTYBOARD_REVE
-opt_set TEMP_SENSOR_0 -2
-opt_set DIGIPOT_I2C_NUM_CHANNELS 5
-opt_set LCD_LANGUAGE it
-opt_set MIXING_STEPPERS 2
-opt_set SERVO_DELAY "{ 300, 300, 300 }"
-opt_enable COREYX USE_XMAX_PLUG MIXING_EXTRUDER GRADIENT_MIX \
-           BABYSTEPPING BABYSTEP_DISPLAY_TOTAL FILAMENT_LCD_DISPLAY \
-           REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER MENU_ADDAUTOSTART SDSUPPORT SDCARD_SORT_ALPHA \
-           ENDSTOP_NOISE_THRESHOLD FAN_SOFT_PWM \
-           FIX_MOUNTED_PROBE AUTO_BED_LEVELING_LINEAR DEBUG_LEVELING_FEATURE FILAMENT_WIDTH_SENSOR PROBE_OFFSET_WIZARD \
-           Z_SAFE_HOMING SHOW_TEMP_ADC_VALUES HOME_Y_BEFORE_X EMERGENCY_PARSER \
-           SD_ABORT_ON_ENDSTOP_HIT HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT ADVANCED_OK M114_DETAIL \
-           VOLUMETRIC_DEFAULT_ON NO_WORKSPACE_OFFSETS EXTRA_FAN_SPEED FWRETRACT \
-           USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE CONTROLLER_FAN_USE_Z_ONLY
-opt_set FAN_MIN_PWM 50
-opt_set FAN_KICKSTART_TIME 100
-opt_set XY_FREQUENCY_LIMIT 15
-opt_add FILWIDTH_PIN 5
-exec_test $1 $2 "Mightyboard Rev. E | CoreXY, Gradient Mix | Endstop Int. | Home Y > X | FW Retract ..." "$3"
-
 ######## Other Standard LCD/Panels ##############
 #
 # ULTRA_LCD
@@ -277,71 +216,15 @@ exec_test $1 $2 "Formbot/T_Rex_3 example configuration." "$3"
 #
 # BQ Hephestos 2
 #restore_configs
-#use_example_configs Hephestos_2
+#use_example_configs BQ/Hephestos_2
 #exec_test $1 $2 "Stuff" "$3"
 
-#
-# Delta Config (generic) + UBL + ALLEN_KEY + EEPROM_SETTINGS + OLED_PANEL_TINYBOY2
-#
-use_example_configs delta/generic
-opt_enable RESTORE_LEVELING_AFTER_G28 EEPROM_SETTINGS EEPROM_CHITCHAT \
-           Z_PROBE_ALLEN_KEY AUTO_BED_LEVELING_UBL \
-           OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY DELTA_CALIBRATION_MENU
-opt_set LCD_LANGUAGE ko_KR
-opt_set X_DRIVER_TYPE L6470
-opt_set Y_DRIVER_TYPE L6470
-opt_set Z_DRIVER_TYPE L6470
-opt_add L6470_CHAIN_SCK_PIN  53
-opt_add L6470_CHAIN_MISO_PIN 49
-opt_add L6470_CHAIN_MOSI_PIN 40
-opt_add L6470_CHAIN_SS_PIN   42
-opt_add "ENABLE_RESET_L64XX_CHIPS(V) NOOP"
-exec_test $1 $2 "DELTA, RAMPS, L6470, UBL, Allen Key, EEPROM, OLED_PANEL_TINYBOY2..." "$3"
-
-#
-# Delta Config (FLSUN AC because it's complex)
-#
-use_example_configs delta/FLSUN/auto_calibrate
-exec_test $1 $2 "RAMPS 1.3 | DELTA | FLSUN AC Config" "$3"
-
 #
 # Makibox Config  need to check board type for Teensy++ 2.0
 #
 #use_example_configs makibox
 #exec_test $1 $2 "Stuff" "$3"
 
-#
-# Test mixed TMC config
-#
-restore_configs
-opt_set LCD_LANGUAGE vi
-opt_set X_DRIVER_TYPE TMC2160
-opt_set Y_DRIVER_TYPE TMC5160
-opt_set Z_DRIVER_TYPE TMC2208_STANDALONE
-opt_set E0_DRIVER_TYPE TMC2130
-opt_set X_MIN_ENDSTOP_INVERTING true
-opt_set Y_MIN_ENDSTOP_INVERTING true
-opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \
-           MARLIN_BRICKOUT MARLIN_INVADERS MARLIN_SNAKE \
-           MONITOR_DRIVER_STATUS STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD \
-           USE_ZMIN_PLUG SENSORLESS_HOMING TMC_DEBUG M114_DETAIL
-exec_test $1 $2 "RAMPS | Mixed TMC | Sensorless | RRDFGSC | Games" "$3"
-
-#
-# SCARA with Mixed TMC
-#
-use_example_configs SCARA/Morgan
-opt_set LCD_LANGUAGE es
-opt_enable USE_ZMIN_PLUG FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR PAUSE_BEFORE_DEPLOY_STOW \
-           MKS_12864OLED EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL Z_SAFE_HOMING \
-           STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD SENSORLESS_HOMING SQUARE_WAVE_STEPPING
-opt_set X_MAX_ENDSTOP_INVERTING false
-opt_set X_DRIVER_TYPE TMC2209
-opt_set Y_DRIVER_TYPE TMC2130
-opt_set Z_DRIVER_TYPE TMC2130_STANDALONE
-opt_set E0_DRIVER_TYPE TMC2660
-exec_test $1 $2 "RAMPS | SCARA | Mixed TMC | EEPROM" "$3"
-
 #
 # tvrrug Config need to check board type for sanguino atmega644p
 #

buildroot/tests/mks_robin-tests

@@ -10,5 +10,13 @@ set -e
 use_example_configs Mks/Robin
 exec_test $1 $2 "MKS Robin config (FSMC Color UI)" "$3"
 
+#
+# MKS Robin LVGL FSMC
+#
+use_example_configs Mks/Robin
+opt_disable TFT_CLASSIC_UI TFT_COLOR_UI TOUCH_SCREEN TFT_RES_320x240
+opt_enable TFT_LVGL_UI TFT_RES_480x320
+exec_test $1 $2 "MKS Robin nano v1.2 LVGL FSMC" "$3"
+
 # cleanup
 restore_configs

buildroot/tests/mks_robin_nano35-tests

@@ -24,15 +24,6 @@ opt_disable TFT_INTERFACE_FSMC
 opt_enable TFT_INTERFACE_SPI
 exec_test $1 $2 "MKS Robin v2 nano Emulated DOGM SPI" "$3"
 
-#
-# MKS Robin nano v1.2 LVGL FSMC
-#
-use_example_configs Mks/Robin
-opt_set MOTHERBOARD BOARD_MKS_ROBIN_NANO
-opt_disable TFT_CLASSIC_UI TFT_COLOR_UI TOUCH_SCREEN TFT_RES_320x240
-opt_enable TFT_LVGL_UI TFT_RES_480x320
-exec_test $1 $2 "MKS Robin nano v1.2 LVGL FSMC" "$3"
-
 #
 # MKS Robin v2 nano LVGL SPI
 # (Robin v2 nano has no FSMC interface)

buildroot/tests/rambo-tests

@@ -81,5 +81,51 @@ opt_set Z_DRIVER_TYPE TMC2130
 opt_set E0_DRIVER_TYPE TMC2130
 exec_test $1 $2 "Einsy RAMBo with TMC2130" "$3"
 
+#
+# Test MINIRAMBO with PWM_MOTOR_CURRENT and many features
+#
+restore_configs
+opt_set MOTHERBOARD BOARD_MINIRAMBO
+opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \
+          SDSUPPORT PCA9632 SOUND_MENU_ITEM GCODE_REPEAT_MARKERS \
+          AUTO_BED_LEVELING_BILINEAR PROBE_MANUALLY LCD_BED_LEVELING G26_MESH_VALIDATION MESH_EDIT_MENU \
+          LIN_ADVANCE EXTRA_LIN_ADVANCE_K \
+          INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT EXPERIMENTAL_I2CBUS M100_FREE_MEMORY_WATCHER \
+          NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE \
+          ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE ADVANCED_PAUSE_CONTINUOUS_PURGE FILAMENT_LOAD_UNLOAD_GCODES \
+          PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 M114_DETAIL
+opt_set CONTROLLERFAN_SPEED_IDLE 128
+opt_add M100_FREE_MEMORY_DUMPER
+opt_add M100_FREE_MEMORY_CORRUPTOR
+opt_set PWM_MOTOR_CURRENT "{ 1300, 1300, 1250 }"
+opt_set I2C_SLAVE_ADDRESS 63
+exec_test $1 $2 "MINIRAMBO | RRDGFSC | M100 | PWM_MOTOR_CURRENT | PRINTCOUNTER | Advanced Pause ..." "$3"
+
+#
+# Test many less common options
+#
+restore_configs
+opt_set MOTHERBOARD BOARD_RAMBO
+opt_set TEMP_SENSOR_0 -2
+opt_set DIGIPOT_I2C_NUM_CHANNELS 5
+opt_set LCD_LANGUAGE it
+opt_set MIXING_STEPPERS 2
+opt_set SERVO_DELAY "{ 300, 300, 300 }"
+opt_enable COREYX USE_XMAX_PLUG MIXING_EXTRUDER GRADIENT_MIX \
+           BABYSTEPPING BABYSTEP_DISPLAY_TOTAL FILAMENT_LCD_DISPLAY \
+           REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER MENU_ADDAUTOSTART SDSUPPORT SDCARD_SORT_ALPHA \
+           ENDSTOP_NOISE_THRESHOLD FAN_SOFT_PWM \
+           FIX_MOUNTED_PROBE AUTO_BED_LEVELING_LINEAR DEBUG_LEVELING_FEATURE FILAMENT_WIDTH_SENSOR PROBE_OFFSET_WIZARD \
+           Z_SAFE_HOMING SHOW_TEMP_ADC_VALUES HOME_Y_BEFORE_X EMERGENCY_PARSER \
+           SD_ABORT_ON_ENDSTOP_HIT HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT ADVANCED_OK M114_DETAIL \
+           VOLUMETRIC_DEFAULT_ON NO_WORKSPACE_OFFSETS EXTRA_FAN_SPEED FWRETRACT \
+           USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE CONTROLLER_FAN_USE_Z_ONLY
+opt_set CONTROLLER_FAN_PIN X_MAX_PIN
+opt_set FAN_MIN_PWM 50
+opt_set FAN_KICKSTART_TIME 100
+opt_set XY_FREQUENCY_LIMIT 15
+opt_add FILWIDTH_PIN 5
+exec_test $1 $2 "Rambo | CoreXY, Gradient Mix | Endstop Int. | Home Y > X | FW Retract ..." "$3"
+
 # clean up
 restore_configs

buildroot/tests/sanguino1284p-tests

@@ -11,7 +11,11 @@ set -e
 #
 restore_configs
 opt_set MOTHERBOARD BOARD_SANGUINOLOLU_12
-exec_test $1 $2 "Default Configuration" "$3"
+opt_set LCD_LANGUAGE de
+opt_enable MINIPANEL USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE
+opt_set CONTROLLER_FAN_PIN 27
+exec_test $1 $2 "Default Configuration | MINIPANAL | CONTROLLER_FAN" "$3"
+
 
 # clean up
 restore_configs