HIGH/LOW naming of pin state settings (#19089)

2020-08-22 06:13:43 +02:00 · 2020-08-22 06:13:43 +02:00 · 8652a7bdd2
parent 93167afaf5
commit 8652a7bdd2
7 changed files with 21 additions and 17 deletions
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@ -330,7 +330,7 @@
 //#define PSU_NAME "Power Supply"

 #if ENABLED(PSU_CONTROL)
-  #define PSU_ACTIVE_HIGH false     // Set 'false' for ATX, 'true' for X-Box
+  #define PSU_ACTIVE_STATE LOW      // Set 'LOW' for ATX, 'HIGH' for X-Box

  //#define PSU_DEFAULT_OFF         // Keep power off until enabled directly with M80
  //#define PSU_POWERUP_DELAY 250   // (ms) Delay for the PSU to warm up to full power
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@ -2851,7 +2851,7 @@
 //#define SPINDLE_FEATURE
 //#define LASER_FEATURE
 #if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
-  #define SPINDLE_LASER_ACTIVE_HIGH     false  // Set to "true" if the on/off function is active HIGH
+  #define SPINDLE_LASER_ACTIVE_STATE    LOW    // Set to "HIGH" if the on/off function is active HIGH
  #define SPINDLE_LASER_PWM             true   // Set to "true" if your controller supports setting the speed/power
  #define SPINDLE_LASER_PWM_INVERT      false  // Set to "true" if the speed/power goes up when you want it to go slower

--- a/Marlin/src/HAL/DUE/usb/arduino_due_x.h
+++ b/Marlin/src/HAL/DUE/usb/arduino_due_x.h
@ -93,5 +93,5 @@
 #define USB_VBOF_GPIO               (PIO_PB10_IDX)
 #define USB_VBOF_FLAGS              (PIO_PERIPH_A | PIO_DEFAULT)
 /*! Active level of the USB_VBOF output pin. */
-#define USB_VBOF_ACTIVE_LEVEL       LOW
+#define USB_VBOF_ACTIVE_STATE       LOW
 /* ------------------------------------------------------------------------ */
--- a/Marlin/src/MarlinCore.h
+++ b/Marlin/src/MarlinCore.h
@ -89,8 +89,8 @@ extern bool wait_for_heatup;

 #if ENABLED(PSU_CONTROL)
  extern bool powersupply_on;
-  #define PSU_PIN_ON()  do{ OUT_WRITE(PS_ON_PIN,  PSU_ACTIVE_HIGH); powersupply_on = true; }while(0)
-  #define PSU_PIN_OFF() do{ OUT_WRITE(PS_ON_PIN, !PSU_ACTIVE_HIGH); powersupply_on = false; }while(0)
+  #define PSU_PIN_ON()  do{ OUT_WRITE(PS_ON_PIN,  PSU_ACTIVE_STATE); powersupply_on = true;  }while(0)
+  #define PSU_PIN_OFF() do{ OUT_WRITE(PS_ON_PIN, !PSU_ACTIVE_STATE); powersupply_on = false; }while(0)
  #if ENABLED(AUTO_POWER_CONTROL)
    #define PSU_ON()  powerManager.power_on()
    #define PSU_OFF() powerManager.power_off()
--- a/Marlin/src/feature/spindle_laser.cpp
+++ b/Marlin/src/feature/spindle_laser.cpp
@ -37,7 +37,7 @@ cutter_power_t SpindleLaser::menuPower,                               // Power s
               SpindleLaser::unitPower;                               // LCD status power in PWM, PERCENT, or RPM

 #if ENABLED(MARLIN_DEV_MODE)
-  cutter_frequency_t SpindleLaser::frequency;                         // setting PWM frequency; range: 2K - 50K
+  cutter_frequency_t SpindleLaser::frequency;                         // PWM frequency setting; range: 2K - 50K
 #endif
 #define SPINDLE_LASER_PWM_OFF ((SPINDLE_LASER_PWM_INVERT) ? 255 : 0)

@ -45,13 +45,13 @@ cutter_power_t SpindleLaser::menuPower,                               // Power s
 // Init the cutter to a safe OFF state
 //
 void SpindleLaser::init() {
-  OUT_WRITE(SPINDLE_LASER_ENA_PIN, !SPINDLE_LASER_ACTIVE_HIGH);       // Init spindle to off
+  OUT_WRITE(SPINDLE_LASER_ENA_PIN, !SPINDLE_LASER_ACTIVE_STATE);      // Init spindle to off
  #if ENABLED(SPINDLE_CHANGE_DIR)
    OUT_WRITE(SPINDLE_DIR_PIN, SPINDLE_INVERT_DIR ? 255 : 0);         // Init rotation to clockwise (M3)
  #endif
  #if ENABLED(SPINDLE_LASER_PWM)
    SET_PWM(SPINDLE_LASER_PWM_PIN);
-    analogWrite(pin_t(SPINDLE_LASER_PWM_PIN), SPINDLE_LASER_PWM_OFF); // set to lowest speed
+    analogWrite(pin_t(SPINDLE_LASER_PWM_PIN), SPINDLE_LASER_PWM_OFF); // Set to lowest speed
  #endif
  #if ENABLED(HAL_CAN_SET_PWM_FREQ) && defined(SPINDLE_LASER_FREQUENCY)
    set_pwm_frequency(pin_t(SPINDLE_LASER_PWM_PIN), SPINDLE_LASER_FREQUENCY);
@ -64,14 +64,14 @@ void SpindleLaser::init() {
   * Set the cutter PWM directly to the given ocr value
   */
  void SpindleLaser::set_ocr(const uint8_t ocr) {
-    WRITE(SPINDLE_LASER_ENA_PIN, SPINDLE_LASER_ACTIVE_HIGH);        // turn spindle on
+    WRITE(SPINDLE_LASER_ENA_PIN, SPINDLE_LASER_ACTIVE_STATE);         // Turn spindle on
    analogWrite(pin_t(SPINDLE_LASER_PWM_PIN), ocr ^ SPINDLE_LASER_PWM_OFF);
    #if NEEDS_HARDWARE_PWM && SPINDLE_LASER_FREQUENCY
      set_pwm_duty(pin_t(SPINDLE_LASER_PWM_PIN), ocr ^ SPINDLE_LASER_PWM_OFF);
    #endif
  }
  void SpindleLaser::ocr_off() {
-    WRITE(SPINDLE_LASER_ENA_PIN, !SPINDLE_LASER_ACTIVE_HIGH);       // Turn spindle off
+    WRITE(SPINDLE_LASER_ENA_PIN, !SPINDLE_LASER_ACTIVE_STATE);        // Turn spindle off
    analogWrite(pin_t(SPINDLE_LASER_PWM_PIN), SPINDLE_LASER_PWM_OFF); // Only write low byte
  }
 #endif
@ -98,7 +98,7 @@ void SpindleLaser::apply_power(const uint8_t opwr) {
      isReady = false;
    }
  #else
-    WRITE(SPINDLE_LASER_ENA_PIN, enabled() == SPINDLE_LASER_ACTIVE_HIGH);
+    WRITE(SPINDLE_LASER_ENA_PIN, enabled() ? SPINDLE_LASER_ACTIVE_STATE : !SPINDLE_LASER_ACTIVE_STATE);
    isReady = true;
  #endif
 }
--- a/Marlin/src/inc/Conditionals_post.h
+++ b/Marlin/src/inc/Conditionals_post.h
@ -403,7 +403,7 @@
 #ifndef PSU_NAME
  #if DISABLED(PSU_CONTROL)
    #define PSU_NAME "Generic"  // No control
-  #elif PSU_ACTIVE_HIGH
+  #elif PSU_ACTIVE_STATE
    #define PSU_NAME "XBox"     // X-Box 360 (203W)
  #else
    #define PSU_NAME "ATX"      // ATX style
--- a/Marlin/src/inc/SanityCheck.h
+++ b/Marlin/src/inc/SanityCheck.h
@ -419,8 +419,10 @@
  #error "SPINDLE_DIR_CHANGE is now SPINDLE_CHANGE_DIR. Please update your Configuration_adv.h."
 #elif defined(SPINDLE_STOP_ON_DIR_CHANGE)
  #error "SPINDLE_STOP_ON_DIR_CHANGE is now SPINDLE_CHANGE_DIR_STOP. Please update your Configuration_adv.h."
+#elif defined(SPINDLE_LASER_ACTIVE_HIGH)
+  #error "SPINDLE_LASER_ACTIVE_HIGH is now SPINDLE_LASER_ACTIVE_STATE. Please update your Configuration_adv.h."
 #elif defined(SPINDLE_LASER_ENABLE_INVERT)
-  #error "SPINDLE_LASER_ENABLE_INVERT is now SPINDLE_LASER_ACTIVE_HIGH. Please update your Configuration_adv.h."
+  #error "SPINDLE_LASER_ENABLE_INVERT is now SPINDLE_LASER_ACTIVE_STATE. Please update your Configuration_adv.h."
 #elif defined(CUTTER_POWER_DISPLAY)
  #error "CUTTER_POWER_DISPLAY is now CUTTER_POWER_UNIT. Please update your Configuration_adv.h."
 #elif defined(CHAMBER_HEATER_PIN)
@ -441,10 +443,12 @@
  #error "USB_SD_DISABLED is now NO_SD_HOST_DRIVE. Please update your Configuration_adv.h."
 #elif defined(USB_SD_ONBOARD)
  #error "USB_SD_ONBOARD is obsolete. Disable NO_SD_HOST_DRIVE instead."
+#elif defined(PSU_ACTIVE_HIGH)
+  #error "PSU_ACTIVE_HIGH is now PSU_ACTIVE_STATE. Please update your configuration."
 #elif POWER_SUPPLY == 1
-  #error "Replace POWER_SUPPLY 1 by enabling PSU_CONTROL and setting PSU_ACTIVE_HIGH to 'false'."
+  #error "Replace POWER_SUPPLY 1 by enabling PSU_CONTROL and setting PSU_ACTIVE_STATE to 'LOW'."
 #elif POWER_SUPPLY == 2
-  #error "Replace POWER_SUPPLY 2 by enabling PSU_CONTROL and setting PSU_ACTIVE_HIGH to 'true'."
+  #error "Replace POWER_SUPPLY 2 by enabling PSU_CONTROL and setting PSU_ACTIVE_STATE to 'HIGH'."
 #elif defined(POWER_SUPPLY)
  #error "POWER_SUPPLY is now obsolete. Please remove it from Configuration.h."
 #elif defined(MKS_ROBIN_TFT)
@ -2923,8 +2927,8 @@ static_assert(   _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
 * Ensure this option is set intentionally
 */
 #if ENABLED(PSU_CONTROL)
-  #ifndef PSU_ACTIVE_HIGH
-    #error "PSU_CONTROL requires PSU_ACTIVE_HIGH to be defined as 'true' or 'false'."
+  #ifndef PSU_ACTIVE_STATE
+    #error "PSU_CONTROL requires PSU_ACTIVE_STATE to be defined as 'HIGH' or 'LOW'."
  #elif !PIN_EXISTS(PS_ON)
    #error "PSU_CONTROL requires PS_ON_PIN."
  #endif