From 995ed90248bc018a867aff337cec78b573459666 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Tue, 4 Apr 2017 18:06:19 -0500 Subject: [PATCH] Clean up Filament Width Sensor comments --- Marlin/Configuration.h | 44 +++++++++++-------- .../Cartesio/Configuration.h | 44 +++++++++++-------- .../Felix/Configuration.h | 44 +++++++++++-------- .../Felix/DUAL/Configuration.h | 44 +++++++++++-------- .../Hephestos/Configuration.h | 44 +++++++++++-------- .../Hephestos_2/Configuration.h | 44 +++++++++++-------- .../K8200/Configuration.h | 44 +++++++++++-------- .../K8400/Configuration.h | 44 +++++++++++-------- .../K8400/Dual-head/Configuration.h | 44 +++++++++++-------- .../RepRapWorld/Megatronics/Configuration.h | 44 +++++++++++-------- .../RigidBot/Configuration.h | 44 +++++++++++-------- .../SCARA/Configuration.h | 44 +++++++++++-------- .../TAZ4/Configuration.h | 44 +++++++++++-------- .../TinyBoy2/Configuration.h | 44 +++++++++++-------- .../WITBOX/Configuration.h | 44 +++++++++++-------- .../adafruit/ST7565/Configuration.h | 44 +++++++++++-------- .../delta/flsun_kossel_mini/Configuration.h | 44 +++++++++++-------- .../delta/generic/Configuration.h | 44 +++++++++++-------- .../delta/kossel_mini/Configuration.h | 44 +++++++++++-------- .../delta/kossel_pro/Configuration.h | 44 +++++++++++-------- .../delta/kossel_xl/Configuration.h | 44 +++++++++++-------- .../makibox/Configuration.h | 44 +++++++++++-------- .../tvrrug/Round2/Configuration.h | 44 +++++++++++-------- 23 files changed, 575 insertions(+), 437 deletions(-) diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 15d7238f5c..c9e54c59df 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -1547,33 +1547,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/Cartesio/Configuration.h b/Marlin/example_configurations/Cartesio/Configuration.h index 05c1036bb2..20b1e495a0 100644 --- a/Marlin/example_configurations/Cartesio/Configuration.h +++ b/Marlin/example_configurations/Cartesio/Configuration.h @@ -1546,33 +1546,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index 1b3704f2e2..a124a5112e 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -1530,33 +1530,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h index 771ece9b3e..d4f4e94637 100644 --- a/Marlin/example_configurations/Felix/DUAL/Configuration.h +++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h @@ -1530,33 +1530,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index 15ad5c2478..8352c2ebc0 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -1538,33 +1538,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h index 9a415d782d..3a48bb0397 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration.h @@ -1541,33 +1541,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 2.00 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.60 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 2.00 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.60 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index 2e78a8c955..632fcf9bbe 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -1580,33 +1580,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/K8400/Configuration.h b/Marlin/example_configurations/K8400/Configuration.h index 98cf55e871..6e9128649f 100644 --- a/Marlin/example_configurations/K8400/Configuration.h +++ b/Marlin/example_configurations/K8400/Configuration.h @@ -1547,33 +1547,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/K8400/Dual-head/Configuration.h b/Marlin/example_configurations/K8400/Dual-head/Configuration.h index 381f771f2b..4c83230a9a 100644 --- a/Marlin/example_configurations/K8400/Dual-head/Configuration.h +++ b/Marlin/example_configurations/K8400/Dual-head/Configuration.h @@ -1547,33 +1547,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index c86a4f8a32..cc55485632 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -1547,33 +1547,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index 4a49291849..084b687829 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -1548,33 +1548,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 063c1e2471..a0526e18f5 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -1562,33 +1562,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index bf9420d8f0..458809ec10 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -1567,33 +1567,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/TinyBoy2/Configuration.h b/Marlin/example_configurations/TinyBoy2/Configuration.h index e99110a2f1..ed78b74517 100644 --- a/Marlin/example_configurations/TinyBoy2/Configuration.h +++ b/Marlin/example_configurations/TinyBoy2/Configuration.h @@ -1598,33 +1598,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index 68c15d8885..eea8a48bfb 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -1538,33 +1538,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index dc612f96b6..4ee1e54a12 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -1547,33 +1547,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h b/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h index 310b102e33..b23be9c14c 100644 --- a/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/flsun_kossel_mini/Configuration.h @@ -1654,33 +1654,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index c14266b676..56210c2b37 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -1638,33 +1638,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 36b95d8c38..649f1f64a0 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -1634,33 +1634,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index 64ebb80fbb..badea5b730 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -1641,33 +1641,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h index dd35df765d..f33c23837b 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h @@ -1649,33 +1649,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index 8db0a52a7a..598fefbeae 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -1550,33 +1550,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index 8285c43a05..74b984fa99 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -1543,33 +1543,39 @@ // With this option servos are powered only during movement, then turned off to prevent jitter. //#define DEACTIVATE_SERVOS_AFTER_MOVE -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) +/** + * Filament Width Sensor * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ //#define FILAMENT_WIDTH_SENSOR -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. #if ENABLED(FILAMENT_WIDTH_SENSOR) - #define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) - #define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber - #define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm - #define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm - #define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. - #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially - //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. //#define FILAMENT_LCD_DISPLAY #endif