Various typo fixes - only in comments, no code changes.
This commit is contained in:
Mark Hanford
parent
7dcd350941
commit
ab0d3c4fb3
|
|
@ -8,7 +8,7 @@
|
|||
//===========================================================================
|
||||
//============================= DELTA Printer ===============================
|
||||
//===========================================================================
|
||||
// For a Delta printer rplace the configuration files wilth the files in the
|
||||
// For a Delta printer replace the configuration files with the files in the
|
||||
// example_configurations/delta directory.
|
||||
//
|
||||
|
||||
|
|
@ -106,7 +106,7 @@
|
|||
// 0 is not used
|
||||
// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
|
||||
// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
|
||||
// 3 is mendel-parts thermistor (4.7k pullup)
|
||||
// 3 is Mendel-parts thermistor (4.7k pullup)
|
||||
// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
|
||||
// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
|
||||
// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
|
||||
|
|
@ -116,7 +116,7 @@
|
|||
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
|
||||
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
|
||||
// 20 is the PT100 circuit found in the Ultimainboard V2.x
|
||||
// 60 is 100k Maker's Tool Works Kapton Bed Thermister
|
||||
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor
|
||||
//
|
||||
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
|
||||
// (but gives greater accuracy and more stable PID)
|
||||
|
|
@ -177,13 +177,13 @@
|
|||
#define K1 0.95 //smoothing factor within the PID
|
||||
#define PID_dT ((OVERSAMPLENR * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
|
||||
// If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
// Ultimaker
|
||||
#define DEFAULT_Kp 22.2
|
||||
#define DEFAULT_Ki 1.08
|
||||
#define DEFAULT_Kd 114
|
||||
|
||||
// Makergear
|
||||
// MakerGear
|
||||
// #define DEFAULT_Kp 7.0
|
||||
// #define DEFAULT_Ki 0.1
|
||||
// #define DEFAULT_Kd 12
|
||||
|
|
@ -252,7 +252,7 @@
|
|||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
#ifndef ENDSTOPPULLUPS
|
||||
// fine Enstop settings: Individual Pullups. will be ignored if ENDSTOPPULLUPS is defined
|
||||
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
||||
// #define ENDSTOPPULLUP_XMAX
|
||||
// #define ENDSTOPPULLUP_YMAX
|
||||
// #define ENDSTOPPULLUP_ZMAX
|
||||
|
|
@ -336,7 +336,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define BACK_PROBE_BED_POSITION 180
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
|
||||
// these are the offsets to the prob relative to the extruder tip (Hotend - Probe)
|
||||
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
|
||||
|
|
@ -357,7 +357,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
// #define PROBE_SERVO_DEACTIVATION_DELAY 300
|
||||
|
||||
|
||||
//If you have enabled the Bed Auto Levelling and are using the same Z Probe for Z Homing,
|
||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||
|
||||
#define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area.
|
||||
|
|
@ -391,7 +391,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
|
||||
//Manual homing switch locations:
|
||||
// For deltabots this means top and center of the cartesian print volume.
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
|
|
@ -405,7 +405,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker
|
||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
||||
|
|
@ -426,11 +426,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//===========================================================================
|
||||
|
||||
// EEPROM
|
||||
// the microcontroller can store settings in the EEPROM, e.g. max velocity...
|
||||
// M500 - stores paramters in EEPROM
|
||||
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
||||
// M500 - stores parameters in EEPROM
|
||||
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
//define this to enable eeprom support
|
||||
//define this to enable EEPROM support
|
||||
//#define EEPROM_SETTINGS
|
||||
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
// please keep turned on if you can.
|
||||
|
|
@ -446,14 +446,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
|
||||
//LCD and SD support
|
||||
//#define ULTRA_LCD //general lcd support, also 16x2
|
||||
//#define ULTRA_LCD //general LCD support, also 16x2
|
||||
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
|
||||
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
||||
//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
|
||||
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
|
||||
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
|
||||
//#define ULTIMAKERCONTROLLER //as available from the ultimaker online store.
|
||||
//#define ULTIPANEL //the ultipanel as on thingiverse
|
||||
//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
|
||||
//#define ULTIPANEL //the UltiPanel as on Thingiverse
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||
|
||||
|
|
@ -594,7 +594,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define LCD_WIDTH 20
|
||||
#define LCD_HEIGHT 4
|
||||
#endif
|
||||
#else //no panel but just lcd
|
||||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 20
|
||||
|
|
@ -616,8 +616,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||
//#define FAST_PWM_FAN
|
||||
|
||||
// Temperature status leds that display the hotend and bet temperature.
|
||||
// If alle hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
|
||||
// Temperature status LEDs that display the hotend and bet temperature.
|
||||
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
|
||||
// Otherwise the RED led is on. There is 1C hysteresis.
|
||||
//#define TEMP_STAT_LEDS
|
||||
|
||||
|
|
|
|||
|
|
@ -20,7 +20,7 @@
|
|||
|
||||
#ifdef PIDTEMP
|
||||
// this adds an experimental additional term to the heating power, proportional to the extrusion speed.
|
||||
// if Kc is choosen well, the additional required power due to increased melting should be compensated.
|
||||
// if Kc is chosen well, the additional required power due to increased melting should be compensated.
|
||||
#define PID_ADD_EXTRUSION_RATE
|
||||
#ifdef PID_ADD_EXTRUSION_RATE
|
||||
#define DEFAULT_Kc (1) //heating power=Kc*(e_speed)
|
||||
|
|
@ -34,7 +34,7 @@
|
|||
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
|
||||
// you exit the value by any M109 without F*
|
||||
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
|
||||
// on an ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
#define AUTOTEMP
|
||||
#ifdef AUTOTEMP
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98
|
||||
|
|
@ -283,11 +283,11 @@
|
|||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
|
||||
#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
|
||||
// if a file is deleted, it frees a block. hence, the order is not purely cronological. To still have auto0.g accessible, there is again the option to do that.
|
||||
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
|
||||
// using:
|
||||
//#define MENU_ADDAUTOSTART
|
||||
|
||||
// The hardware watchdog should reset the Microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||
//#define USE_WATCHDOG
|
||||
|
||||
#ifdef USE_WATCHDOG
|
||||
|
|
@ -301,7 +301,7 @@
|
|||
//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
|
||||
|
||||
// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
|
||||
// it can e.g. be used to change z-positions in the print startup phase in realtime
|
||||
// it can e.g. be used to change z-positions in the print startup phase in real-time
|
||||
// does not respect endstops!
|
||||
//#define BABYSTEPPING
|
||||
#ifdef BABYSTEPPING
|
||||
|
|
@ -324,8 +324,8 @@
|
|||
//
|
||||
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
|
||||
//
|
||||
// hooke's law says: force = k * distance
|
||||
// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant
|
||||
// Hooke's law says: force = k * distance
|
||||
// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
|
||||
// so: v ^ 2 is proportional to number of steps we advance the extruder
|
||||
//#define ADVANCE
|
||||
|
||||
|
|
@ -379,7 +379,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
//===========================================================================
|
||||
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
|
||||
#if defined SDSUPPORT
|
||||
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#else
|
||||
|
|
@ -387,12 +387,12 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#endif
|
||||
|
||||
|
||||
//The ASCII buffer for recieving from the serial:
|
||||
//The ASCII buffer for receiving from the serial:
|
||||
#define MAX_CMD_SIZE 96
|
||||
#define BUFSIZE 4
|
||||
|
||||
|
||||
// Firmware based and LCD controled retract
|
||||
// Firmware based and LCD controlled retract
|
||||
// M207 and M208 can be used to define parameters for the retraction.
|
||||
// The retraction can be called by the slicer using G10 and G11
|
||||
// until then, intended retractions can be detected by moves that only extrude and the direction.
|
||||
|
|
|
|||
Loading…
Reference in a new issue