Divide up Conditionals to get LCD items early
This commit is contained in:
Scott Lahteine
parent
33c7c6e11d
commit
b6d381f863
|
|
@ -5,7 +5,16 @@
|
|||
#ifndef CONDITIONALS_H
|
||||
#define CONDITIONALS_H
|
||||
|
||||
#include "Arduino.h"
|
||||
#ifndef AT90USB
|
||||
#define HardwareSerial_h // trick to disable the standard HWserial
|
||||
#endif
|
||||
|
||||
#if (ARDUINO >= 100)
|
||||
#include "Arduino.h"
|
||||
#else
|
||||
#include "WProgram.h"
|
||||
#endif
|
||||
|
||||
#include "pins.h"
|
||||
|
||||
/**
|
||||
|
|
@ -39,159 +48,6 @@
|
|||
#define QUICK_HOME //SCARA needs Quickhome
|
||||
#endif
|
||||
|
||||
|
||||
/**
|
||||
* LCD Controllers
|
||||
*/
|
||||
|
||||
#if defined (MAKRPANEL)
|
||||
#define DOGLCD
|
||||
#define SDSUPPORT
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#define DEFAULT_LCD_CONTRAST 17
|
||||
#endif
|
||||
|
||||
#if defined(miniVIKI) || defined(VIKI2)
|
||||
#define ULTRA_LCD //general LCD support, also 16x2
|
||||
#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
|
||||
#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
|
||||
|
||||
#ifdef miniVIKI
|
||||
#define DEFAULT_LCD_CONTRAST 95
|
||||
#else
|
||||
#define DEFAULT_LCD_CONTRAST 40
|
||||
#endif
|
||||
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#endif
|
||||
|
||||
#ifdef PANEL_ONE
|
||||
#define SDSUPPORT
|
||||
#define ULTIMAKERCONTROLLER
|
||||
#endif
|
||||
|
||||
#ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
#define DOGLCD
|
||||
#define U8GLIB_ST7920
|
||||
#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
#endif
|
||||
|
||||
#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
#ifdef REPRAPWORLD_KEYPAD
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
#ifdef RA_CONTROL_PANEL
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#define LCD_I2C_TYPE_PCA8574
|
||||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||||
#endif
|
||||
|
||||
/**
|
||||
* I2C PANELS
|
||||
*/
|
||||
|
||||
#ifdef LCD_I2C_SAINSMART_YWROBOT
|
||||
// This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
|
||||
// Make sure it is placed in the Arduino libraries directory.
|
||||
#define LCD_I2C_TYPE_PCF8575
|
||||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
|
||||
#ifdef LCD_I2C_PANELOLU2
|
||||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||||
// (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
|
||||
// Note: The PANELOLU2 encoder click input can either be directly connected to a pin
|
||||
// (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
|
||||
#define LCD_I2C_TYPE_MCP23017
|
||||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
|
||||
#ifndef ENCODER_PULSES_PER_STEP
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
#endif
|
||||
|
||||
#ifndef ENCODER_STEPS_PER_MENU_ITEM
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#endif
|
||||
|
||||
|
||||
#ifdef LCD_USE_I2C_BUZZER
|
||||
#define LCD_FEEDBACK_FREQUENCY_HZ 1000
|
||||
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||||
#ifdef LCD_I2C_VIKI
|
||||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||||
// Note: The pause/stop/resume LCD button pin should be connected to the Arduino
|
||||
// BTN_ENC pin (or set BTN_ENC to -1 if not used)
|
||||
#define LCD_I2C_TYPE_MCP23017
|
||||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
#ifdef SAV_3DLCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shiftregister
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
|
||||
#ifdef ULTIPANEL
|
||||
#define NEWPANEL //enable this if you have a click-encoder panel
|
||||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_HEIGHT 4
|
||||
#endif
|
||||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
#define LCD_HEIGHT 2
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Default LCD contrast for dogm-like LCD displays
|
||||
*/
|
||||
#if defined(DOGLCD) && !defined(DEFAULT_LCD_CONTRAST)
|
||||
#define DEFAULT_LCD_CONTRAST 32
|
||||
#endif
|
||||
|
||||
/**
|
||||
* AUTOSET LOCATIONS OF LIMIT SWITCHES
|
||||
* Added by ZetaPhoenix 09-15-2012
|
||||
|
|
|
|||
155
Marlin/Conditionals_lcd.h
Normal file
155
Marlin/Conditionals_lcd.h
Normal file
|
|
@ -0,0 +1,155 @@
|
|||
/**
|
||||
* Conditionals_lcd.h
|
||||
* LCD-oriented defines that depend on configuration.
|
||||
*/
|
||||
#ifndef CONDITIONALS_LCD_H
|
||||
#define CONDITIONALS_LCD_H
|
||||
|
||||
#if defined(MAKRPANEL)
|
||||
#define DOGLCD
|
||||
#define SDSUPPORT
|
||||
#define DEFAULT_LCD_CONTRAST 17
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
#if defined(miniVIKI) || defined(VIKI2)
|
||||
#define ULTRA_LCD //general LCD support, also 16x2
|
||||
#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
|
||||
#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
|
||||
|
||||
#ifdef miniVIKI
|
||||
#define DEFAULT_LCD_CONTRAST 95
|
||||
#else
|
||||
#define DEFAULT_LCD_CONTRAST 40
|
||||
#endif
|
||||
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#endif
|
||||
|
||||
#ifdef PANEL_ONE
|
||||
#define SDSUPPORT
|
||||
#define ULTIMAKERCONTROLLER
|
||||
#endif
|
||||
|
||||
#ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
#define DOGLCD
|
||||
#define U8GLIB_ST7920
|
||||
#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
#endif
|
||||
|
||||
#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
#ifdef REPRAPWORLD_KEYPAD
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
#ifdef RA_CONTROL_PANEL
|
||||
#define LCD_I2C_TYPE_PCA8574
|
||||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
/**
|
||||
* I2C PANELS
|
||||
*/
|
||||
|
||||
#ifdef LCD_I2C_SAINSMART_YWROBOT
|
||||
// This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
|
||||
// Make sure it is placed in the Arduino libraries directory.
|
||||
#define LCD_I2C_TYPE_PCF8575
|
||||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
|
||||
#ifdef LCD_I2C_PANELOLU2
|
||||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||||
// (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
|
||||
// Note: The PANELOLU2 encoder click input can either be directly connected to a pin
|
||||
// (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
|
||||
#define LCD_I2C_TYPE_MCP23017
|
||||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
|
||||
|
||||
#ifndef ENCODER_PULSES_PER_STEP
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
#endif
|
||||
|
||||
#ifndef ENCODER_STEPS_PER_MENU_ITEM
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#endif
|
||||
|
||||
#ifdef LCD_USE_I2C_BUZZER
|
||||
#define LCD_FEEDBACK_FREQUENCY_HZ 1000
|
||||
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
|
||||
#endif
|
||||
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||||
#ifdef LCD_I2C_VIKI
|
||||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||||
// Note: The pause/stop/resume LCD button pin should be connected to the Arduino
|
||||
// BTN_ENC pin (or set BTN_ENC to -1 if not used)
|
||||
#define LCD_I2C_TYPE_MCP23017
|
||||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
#ifdef SAV_3DLCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shiftregister
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
|
||||
#ifdef ULTIPANEL
|
||||
#define NEWPANEL //enable this if you have a click-encoder panel
|
||||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_HEIGHT 4
|
||||
#endif
|
||||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
#define LCD_HEIGHT 2
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Default LCD contrast for dogm-like LCD displays
|
||||
*/
|
||||
#if defined(DOGLCD) && !defined(DEFAULT_LCD_CONTRAST)
|
||||
#define DEFAULT_LCD_CONTRAST 32
|
||||
#endif
|
||||
|
||||
#endif //CONDITIONALS_LCD_H
|
||||
|
|
@ -713,6 +713,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -110,41 +110,41 @@
|
|||
// allowing faster printing speeds.
|
||||
//#define DUAL_X_CARRIAGE
|
||||
#ifdef DUAL_X_CARRIAGE
|
||||
// Configuration for second X-carriage
|
||||
// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
|
||||
// the second x-carriage always homes to the maximum endstop.
|
||||
#define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
|
||||
#define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
|
||||
#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
|
||||
#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
|
||||
// However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software
|
||||
// override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
|
||||
// without modifying the firmware (through the "M218 T1 X???" command).
|
||||
// Remember: you should set the second extruder x-offset to 0 in your slicer.
|
||||
// Configuration for second X-carriage
|
||||
// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
|
||||
// the second x-carriage always homes to the maximum endstop.
|
||||
#define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
|
||||
#define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
|
||||
#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
|
||||
#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
|
||||
// However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software
|
||||
// override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
|
||||
// without modifying the firmware (through the "M218 T1 X???" command).
|
||||
// Remember: you should set the second extruder x-offset to 0 in your slicer.
|
||||
|
||||
// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h)
|
||||
#define X2_ENABLE_PIN 29
|
||||
#define X2_STEP_PIN 25
|
||||
#define X2_DIR_PIN 23
|
||||
// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h)
|
||||
#define X2_ENABLE_PIN 29
|
||||
#define X2_STEP_PIN 25
|
||||
#define X2_DIR_PIN 23
|
||||
|
||||
// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
|
||||
// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
|
||||
// as long as it supports dual x-carriages. (M605 S0)
|
||||
// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
|
||||
// that additional slicer support is not required. (M605 S1)
|
||||
// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
|
||||
// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
|
||||
// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
|
||||
// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
|
||||
// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
|
||||
// as long as it supports dual x-carriages. (M605 S0)
|
||||
// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
|
||||
// that additional slicer support is not required. (M605 S1)
|
||||
// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
|
||||
// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
|
||||
// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
|
||||
|
||||
// This is the default power-up mode which can be later using M605.
|
||||
#define DEFAULT_DUAL_X_CARRIAGE_MODE 0
|
||||
// This is the default power-up mode which can be later using M605.
|
||||
#define DEFAULT_DUAL_X_CARRIAGE_MODE 0
|
||||
|
||||
// Default settings in "Auto-park Mode"
|
||||
#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
|
||||
#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
|
||||
// Default settings in "Auto-park Mode"
|
||||
#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
|
||||
#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
|
||||
|
||||
// Default x offset in duplication mode (typically set to half print bed width)
|
||||
#define DEFAULT_DUPLICATION_X_OFFSET 100
|
||||
// Default x offset in duplication mode (typically set to half print bed width)
|
||||
#define DEFAULT_DUPLICATION_X_OFFSET 100
|
||||
|
||||
#endif //DUAL_X_CARRIAGE
|
||||
|
||||
|
|
@ -163,20 +163,15 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#endif
|
||||
|
||||
//Comment to disable setting feedrate multiplier via encoder
|
||||
#ifdef ULTIPANEL
|
||||
#define ULTIPANEL_FEEDMULTIPLY
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
|
@ -301,7 +296,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
|
||||
#if defined SDSUPPORT
|
||||
#ifdef SDSUPPORT
|
||||
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
|
|
@ -331,9 +326,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -20,11 +20,6 @@
|
|||
|
||||
#include "fastio.h"
|
||||
#include "Configuration.h"
|
||||
#include "pins.h"
|
||||
|
||||
#ifndef AT90USB
|
||||
#define HardwareSerial_h // trick to disable the standard HWserial
|
||||
#endif
|
||||
|
||||
#if (ARDUINO >= 100)
|
||||
#include "Arduino.h"
|
||||
|
|
@ -191,17 +186,17 @@ void ClearToSend();
|
|||
|
||||
void get_coordinates();
|
||||
#ifdef DELTA
|
||||
void calculate_delta(float cartesian[3]);
|
||||
void calculate_delta(float cartesian[3]);
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
extern int delta_grid_spacing[2];
|
||||
void adjust_delta(float cartesian[3]);
|
||||
extern int delta_grid_spacing[2];
|
||||
void adjust_delta(float cartesian[3]);
|
||||
#endif
|
||||
extern float delta[3];
|
||||
void prepare_move_raw();
|
||||
extern float delta[3];
|
||||
void prepare_move_raw();
|
||||
#endif
|
||||
#ifdef SCARA
|
||||
void calculate_delta(float cartesian[3]);
|
||||
void calculate_SCARA_forward_Transform(float f_scara[3]);
|
||||
void calculate_delta(float cartesian[3]);
|
||||
void calculate_SCARA_forward_Transform(float f_scara[3]);
|
||||
#endif
|
||||
void reset_bed_level();
|
||||
void prepare_move();
|
||||
|
|
@ -209,7 +204,7 @@ void kill();
|
|||
void Stop();
|
||||
|
||||
#ifdef FILAMENT_RUNOUT_SENSOR
|
||||
void filrunout();
|
||||
void filrunout();
|
||||
#endif
|
||||
|
||||
bool IsStopped();
|
||||
|
|
@ -223,7 +218,7 @@ void clamp_to_software_endstops(float target[3]);
|
|||
void refresh_cmd_timeout(void);
|
||||
|
||||
#ifdef FAST_PWM_FAN
|
||||
void setPwmFrequency(uint8_t pin, int val);
|
||||
void setPwmFrequency(uint8_t pin, int val);
|
||||
#endif
|
||||
|
||||
#ifndef CRITICAL_SECTION_START
|
||||
|
|
@ -242,14 +237,14 @@ extern float volumetric_multiplier[EXTRUDERS]; // reciprocal of cross-sectional
|
|||
extern float current_position[NUM_AXIS] ;
|
||||
extern float add_homing[3];
|
||||
#ifdef DELTA
|
||||
extern float endstop_adj[3];
|
||||
extern float delta_radius;
|
||||
extern float delta_diagonal_rod;
|
||||
extern float delta_segments_per_second;
|
||||
void recalc_delta_settings(float radius, float diagonal_rod);
|
||||
extern float endstop_adj[3];
|
||||
extern float delta_radius;
|
||||
extern float delta_diagonal_rod;
|
||||
extern float delta_segments_per_second;
|
||||
void recalc_delta_settings(float radius, float diagonal_rod);
|
||||
#endif
|
||||
#ifdef SCARA
|
||||
extern float axis_scaling[3]; // Build size scaling
|
||||
extern float axis_scaling[3]; // Build size scaling
|
||||
#endif
|
||||
extern float min_pos[3];
|
||||
extern float max_pos[3];
|
||||
|
|
@ -257,12 +252,12 @@ extern bool axis_known_position[3];
|
|||
extern float zprobe_zoffset;
|
||||
extern int fanSpeed;
|
||||
#ifdef BARICUDA
|
||||
extern int ValvePressure;
|
||||
extern int EtoPPressure;
|
||||
extern int ValvePressure;
|
||||
extern int EtoPPressure;
|
||||
#endif
|
||||
|
||||
#ifdef FAN_SOFT_PWM
|
||||
extern unsigned char fanSpeedSoftPwm;
|
||||
extern unsigned char fanSpeedSoftPwm;
|
||||
#endif
|
||||
|
||||
#ifdef FILAMENT_SENSOR
|
||||
|
|
@ -276,10 +271,10 @@ extern unsigned char fanSpeedSoftPwm;
|
|||
#endif
|
||||
|
||||
#ifdef FWRETRACT
|
||||
extern bool autoretract_enabled;
|
||||
extern bool retracted[EXTRUDERS];
|
||||
extern float retract_length, retract_length_swap, retract_feedrate, retract_zlift;
|
||||
extern float retract_recover_length, retract_recover_length_swap, retract_recover_feedrate;
|
||||
extern bool autoretract_enabled;
|
||||
extern bool retracted[EXTRUDERS];
|
||||
extern float retract_length, retract_length_swap, retract_feedrate, retract_zlift;
|
||||
extern float retract_recover_length, retract_recover_length_swap, retract_recover_feedrate;
|
||||
#endif
|
||||
|
||||
extern unsigned long starttime;
|
||||
|
|
@ -289,11 +284,10 @@ extern unsigned long stoptime;
|
|||
extern uint8_t active_extruder;
|
||||
|
||||
#ifdef DIGIPOT_I2C
|
||||
extern void digipot_i2c_set_current( int channel, float current );
|
||||
extern void digipot_i2c_init();
|
||||
#endif
|
||||
|
||||
extern void digipot_i2c_set_current( int channel, float current );
|
||||
extern void digipot_i2c_init();
|
||||
#endif
|
||||
|
||||
extern void calculate_volumetric_multipliers();
|
||||
|
||||
#endif //MARLIN_H
|
||||
|
|
|
|||
|
|
@ -33,9 +33,7 @@ struct pin_map_t {
|
|||
uint8_t bit;
|
||||
};
|
||||
//------------------------------------------------------------------------------
|
||||
#if defined(__AVR_ATmega1280__)\
|
||||
|| defined(__AVR_ATmega2560__)
|
||||
// Mega
|
||||
#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__) // Mega
|
||||
|
||||
// Two Wire (aka I2C) ports
|
||||
uint8_t const SDA_PIN = 20; // D1
|
||||
|
|
@ -43,6 +41,7 @@ uint8_t const SCL_PIN = 21; // D0
|
|||
|
||||
#undef MOSI_PIN
|
||||
#undef MISO_PIN
|
||||
#undef SCK_PIN
|
||||
// SPI port
|
||||
uint8_t const SS_PIN = 53; // B0
|
||||
uint8_t const MOSI_PIN = 51; // B2
|
||||
|
|
|
|||
|
|
@ -756,6 +756,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -180,7 +180,7 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
|
|
@ -188,14 +188,9 @@
|
|||
|
||||
// @section lcd
|
||||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#endif
|
||||
|
||||
//Comment to disable setting feedrate multiplier via encoder
|
||||
#ifdef ULTIPANEL
|
||||
#define ULTIPANEL_FEEDMULTIPLY
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
|
|
@ -368,9 +363,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -692,6 +692,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -689,6 +689,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//#define FILAMENT_LCD_DISPLAY
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -163,20 +163,15 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#endif
|
||||
|
||||
//Comment to disable setting feedrate multiplier via encoder
|
||||
#ifdef ULTIPANEL
|
||||
#define ULTIPANEL_FEEDMULTIPLY
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
|
@ -351,9 +346,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -720,6 +720,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -167,20 +167,15 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#endif
|
||||
|
||||
//Comment to disable setting feedrate multiplier via encoder
|
||||
#ifdef ULTIPANEL
|
||||
#define ULTIPANEL_FEEDMULTIPLY
|
||||
#define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
|
@ -335,9 +330,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8*60 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -724,6 +724,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -163,20 +163,15 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#endif
|
||||
|
||||
//Comment to disable setting feedrate multiplier via encoder
|
||||
#ifdef ULTIPANEL
|
||||
#define ULTIPANEL_FEEDMULTIPLY
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
|
@ -331,9 +326,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -750,6 +750,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -165,20 +165,15 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 240
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 10*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#endif
|
||||
|
||||
//Comment to disable setting feedrate multiplier via encoder
|
||||
#ifdef ULTIPANEL
|
||||
#define ULTIPANEL_FEEDMULTIPLY
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 10*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
|
@ -335,9 +330,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -717,6 +717,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -167,20 +167,15 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#endif
|
||||
|
||||
//Comment to disable setting feedrate multiplier via encoder
|
||||
#ifdef ULTIPANEL
|
||||
#define ULTIPANEL_FEEDMULTIPLY
|
||||
#define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
|
@ -335,9 +330,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8*60 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -734,6 +734,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -166,7 +166,7 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
|
|
@ -174,7 +174,7 @@
|
|||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
|
@ -330,9 +330,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -736,6 +736,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -166,7 +166,7 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
|
|
@ -174,7 +174,7 @@
|
|||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
|
@ -329,9 +329,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -715,6 +715,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -165,20 +165,15 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#endif
|
||||
|
||||
//Comment to disable setting feedrate multiplier via encoder
|
||||
#ifdef ULTIPANEL
|
||||
#define ULTIPANEL_FEEDMULTIPLY
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
|
@ -332,9 +327,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -722,6 +722,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
|
||||
#include "Conditionals_lcd.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
|
|
|||
|
|
@ -167,20 +167,15 @@
|
|||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle. Set to 0 to deactivate.
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#endif
|
||||
|
||||
// Comment to disable setting feedrate multiplier via encoder
|
||||
#ifdef ULTIPANEL
|
||||
#define ULTIPANEL_FEEDMULTIPLY
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
|
|
@ -339,9 +334,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
//#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
|
|
|
|||
|
|
@ -5,8 +5,6 @@
|
|||
#ifndef PINS_H
|
||||
#define PINS_H
|
||||
|
||||
#include "boards.h"
|
||||
|
||||
// Preset optional pins
|
||||
#define X_MS1_PIN -1
|
||||
#define X_MS2_PIN -1
|
||||
|
|
|
|||
|
|
@ -1,4 +1,3 @@
|
|||
#include "temperature.h"
|
||||
#include "ultralcd.h"
|
||||
#ifdef ULTRA_LCD
|
||||
#include "Marlin.h"
|
||||
|
|
|
|||
|
|
@ -14,10 +14,10 @@
|
|||
void lcd_reset_alert_level();
|
||||
bool lcd_detected(void);
|
||||
|
||||
#ifdef DOGLCD
|
||||
extern int lcd_contrast;
|
||||
void lcd_setcontrast(uint8_t value);
|
||||
#endif
|
||||
#ifdef DOGLCD
|
||||
extern int lcd_contrast;
|
||||
void lcd_setcontrast(uint8_t value);
|
||||
#endif
|
||||
|
||||
static unsigned char blink = 0; // Variable for visualization of fan rotation in GLCD
|
||||
|
||||
|
|
@ -28,27 +28,26 @@
|
|||
#define LCD_TIMEOUT_TO_STATUS 15000
|
||||
|
||||
#ifdef ULTIPANEL
|
||||
void lcd_buttons_update();
|
||||
extern volatile uint8_t buttons; //the last checked buttons in a bit array.
|
||||
#ifdef REPRAPWORLD_KEYPAD
|
||||
extern volatile uint8_t buttons_reprapworld_keypad; // to store the keypad shift register values
|
||||
#endif
|
||||
void lcd_buttons_update();
|
||||
extern volatile uint8_t buttons; //the last checked buttons in a bit array.
|
||||
#ifdef REPRAPWORLD_KEYPAD
|
||||
extern volatile uint8_t buttons_reprapworld_keypad; // to store the keypad shift register values
|
||||
#endif
|
||||
#else
|
||||
FORCE_INLINE void lcd_buttons_update() {}
|
||||
FORCE_INLINE void lcd_buttons_update() {}
|
||||
#endif
|
||||
|
||||
extern int plaPreheatHotendTemp;
|
||||
extern int plaPreheatHPBTemp;
|
||||
extern int plaPreheatFanSpeed;
|
||||
|
||||
extern int absPreheatHotendTemp;
|
||||
extern int absPreheatHPBTemp;
|
||||
extern int absPreheatFanSpeed;
|
||||
|
||||
|
||||
extern bool cancel_heatup;
|
||||
|
||||
#ifdef FILAMENT_LCD_DISPLAY
|
||||
extern unsigned long message_millis;
|
||||
extern unsigned long message_millis;
|
||||
#endif
|
||||
|
||||
void lcd_buzz(long duration,uint16_t freq);
|
||||
|
|
|
|||
Loading…
Reference in a new issue