From e78274a7f462ac596d2d618e319da4a5908e16a5 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Mon, 22 Aug 2016 17:05:22 -0500 Subject: [PATCH] Consistent order/formatting of pins files --- Marlin/pins_3DRAG.h | 47 ++++++---- Marlin/pins_5DPRINT.h | 58 ++++++++----- Marlin/pins_99.h | 43 ++++++--- Marlin/pins_A4JP.h | 155 ++++++++++++++++++--------------- Marlin/pins_AZTEEG_X3_PRO.h | 84 ++++++++++-------- Marlin/pins_BRAINWAVE.h | 25 ++++-- Marlin/pins_BRAINWAVE_PRO.h | 30 +++++-- Marlin/pins_CHEAPTRONIC.h | 88 ++++++++++--------- Marlin/pins_CNCONTROLS_11.h | 134 +++++++++++++++------------- Marlin/pins_CNCONTROLS_12.h | 159 +++++++++++++++++++--------------- Marlin/pins_ELEFU_3.h | 82 +++++++++++------- Marlin/pins_GEN3_MONOLITHIC.h | 62 +++++++------ Marlin/pins_GEN3_PLUS.h | 46 ++++++---- Marlin/pins_GEN6.h | 73 +++++++++------- Marlin/pins_GEN7_12.h | 98 ++++++++++++--------- Marlin/pins_LEAPFROG.h | 57 ++++++++---- Marlin/pins_MEGACONTROLLER.h | 138 +++++++++++++++++------------ Marlin/pins_MEGATRONICS.h | 51 ++++++++--- Marlin/pins_MEGATRONICS_2.h | 123 ++++++++++++++++---------- Marlin/pins_MEGATRONICS_3.h | 134 ++++++++++++++++------------ Marlin/pins_MINIRAMBO.h | 138 +++++++++++++++++------------ Marlin/pins_MINITRONICS.h | 121 ++++++++++++++------------ Marlin/pins_RAMBO.h | 134 +++++++++++++++------------- Marlin/pins_RAMPS.h | 47 ++++++---- Marlin/pins_RAMPS_OLD.h | 55 ++++++++---- Marlin/pins_RUMBA.h | 60 ++++++++----- Marlin/pins_SETHI.h | 69 ++++++++------- Marlin/pins_ULTIMAIN_2.h | 104 ++++++++++++---------- Marlin/pins_ULTIMAKER.h | 83 +++++++++++------- Marlin/pins_ULTIMAKER_OLD.h | 85 +++++++++++------- 30 files changed, 1553 insertions(+), 1030 deletions(-) diff --git a/Marlin/pins_3DRAG.h b/Marlin/pins_3DRAG.h index d0445f564f..726ac375fa 100644 --- a/Marlin/pins_3DRAG.h +++ b/Marlin/pins_3DRAG.h @@ -42,20 +42,35 @@ #include "pins_RAMPS.h" -#define HEATER_2_PIN 6 - -#undef Z_ENABLE_PIN -#define Z_ENABLE_PIN 63 - +// +// Limit Switches +// #undef Z_MAX_PIN #define Z_MAX_PIN -1 +// +// Steppers +// +#undef Z_ENABLE_PIN +#define Z_ENABLE_PIN 63 + +// +// SD Card +// #undef SDSS #define SDSS 25//53 +// +// Heaters / Fans +// +#define HEATER_2_PIN 6 + +// +// LCD / Controller +// #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) #undef BEEPER_PIN - #define BEEPER_PIN -1 + #define BEEPER_PIN -1 #undef LCD_PINS_RS #undef LCD_PINS_ENABLE @@ -63,23 +78,23 @@ #undef LCD_PINS_D5 #undef LCD_PINS_D6 #undef LCD_PINS_D7 - #define LCD_PINS_RS 27 - #define LCD_PINS_ENABLE 29 - #define LCD_PINS_D4 37 - #define LCD_PINS_D5 35 - #define LCD_PINS_D6 33 - #define LCD_PINS_D7 31 + #define LCD_PINS_RS 27 + #define LCD_PINS_ENABLE 29 + #define LCD_PINS_D4 37 + #define LCD_PINS_D5 35 + #define LCD_PINS_D6 33 + #define LCD_PINS_D7 31 // Buttons #undef BTN_EN1 #undef BTN_EN2 #undef BTN_ENC - #define BTN_EN1 16 - #define BTN_EN2 17 - #define BTN_ENC 23 + #define BTN_EN1 16 + #define BTN_EN2 17 + #define BTN_ENC 23 #else - #define BEEPER_PIN 33 + #define BEEPER_PIN 33 #endif // ULTRA_LCD && NEWPANEL diff --git a/Marlin/pins_5DPRINT.h b/Marlin/pins_5DPRINT.h index dae7e2034f..9bb67ecb92 100644 --- a/Marlin/pins_5DPRINT.h +++ b/Marlin/pins_5DPRINT.h @@ -35,45 +35,59 @@ #define LARGE_FLASH true +// +// Limit Switches +// +#define X_STOP_PIN 37 +#define Y_STOP_PIN 36 +#define Z_STOP_PIN 39 + +// +// Steppers +// #define X_STEP_PIN 0 #define X_DIR_PIN 1 #define X_ENABLE_PIN 23 -#define X_STOP_PIN 37 #define Y_STEP_PIN 2 #define Y_DIR_PIN 3 #define Y_ENABLE_PIN 19 -#define Y_STOP_PIN 36 #define Z_STEP_PIN 4 #define Z_DIR_PIN 5 #define Z_ENABLE_PIN 18 -#define Z_STOP_PIN 39 #define E0_STEP_PIN 6 #define E0_DIR_PIN 7 #define E0_ENABLE_PIN 17 -#define HEATER_0_PIN 21 // Extruder -#define HEATER_BED_PIN 20 // Bed +// Microstepping pins - Mapping not from fastio.h (?) +#define X_MS1_PIN 25 +#define X_MS2_PIN 26 +#define Y_MS1_PIN 9 +#define Y_MS2_PIN 8 +#define Z_MS1_PIN 7 +#define Z_MS2_PIN 6 +#define E0_MS1_PIN 5 +#define E0_MS2_PIN 4 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 1 // Analog +#define TEMP_BED_PIN 0 // Analog + +// +// Heaters / Fans +// +#define HEATER_0_PIN 21 +#define HEATER_BED_PIN 20 + // You may need to change FAN_PIN to 16 because Marlin isn't using fastio.h // for the fan and Teensyduino uses a different pin mapping. -#define FAN_PIN 16 // Fan +#define FAN_PIN 16 -#define TEMP_0_PIN 1 // Extruder / Analog pin numbering -#define TEMP_BED_PIN 0 // Bed / Analog pin numbering - -// The SDSS pin uses a different pin mapping from file fastio.h +// +// SD Card +// #define SDSS 20 - -// Microstepping pins -// Note that the pin mapping is not from fastio.h -// See Sd2PinMap.h for the pin configurations ??? -#define X_MS1_PIN 25 -#define X_MS2_PIN 26 -#define Y_MS1_PIN 9 -#define Y_MS2_PIN 8 -#define Z_MS1_PIN 7 -#define Z_MS2_PIN 6 -#define E0_MS1_PIN 5 -#define E0_MS2_PIN 4 diff --git a/Marlin/pins_99.h b/Marlin/pins_99.h index 6b7d1e8911..f5d7ec32e9 100644 --- a/Marlin/pins_99.h +++ b/Marlin/pins_99.h @@ -23,31 +23,46 @@ /** * Board 99 pin assignments */ + #define BOARD_NAME "99 Unknown" - + +// +// Limit Switches +// +#define X_STOP_PIN 16 +#define Y_STOP_PIN 67 +#define Z_STOP_PIN 59 + +// +// Steppers +// #define X_STEP_PIN 2 #define X_DIR_PIN 3 -#define X_ENABLE_PIN -1 -#define X_STOP_PIN 16 +#define X_ENABLE_PIN -1 #define Y_STEP_PIN 5 #define Y_DIR_PIN 6 #define Y_ENABLE_PIN -1 -#define Y_STOP_PIN 67 -#define Z_STEP_PIN 62 -#define Z_DIR_PIN 63 +#define Z_STEP_PIN 62 +#define Z_DIR_PIN 63 #define Z_ENABLE_PIN -1 -#define Z_STOP_PIN 59 -#define E0_STEP_PIN 65 -#define E0_DIR_PIN 66 +#define E0_STEP_PIN 65 +#define E0_DIR_PIN 66 #define E0_ENABLE_PIN -1 +// +// Temperature Sensors +// +#define TEMP_0_PIN 6 // ANALOG INPUT - NOT DIGITAL OUTPUT +#define TEMP_BED_PIN 10 + +// +// Heaters / Fans +// +#define HEATER_0_PIN 13 +#define HEATER_BED_PIN 4 + #define SDSS 53 #define PS_ON_PIN 9 - -#define HEATER_0_PIN 13 -#define TEMP_0_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! -#define HEATER_BED_PIN 4 -#define TEMP_BED_PIN 10 diff --git a/Marlin/pins_A4JP.h b/Marlin/pins_A4JP.h index 990abc3092..28db6c8eae 100644 --- a/Marlin/pins_A4JP.h +++ b/Marlin/pins_A4JP.h @@ -30,39 +30,15 @@ #define BOARD_NAME "AJ4P" -// Servo support +// +// Servos +// #define SERVO0_PIN 22 // Motor header MX1 #define SERVO1_PIN 23 // Motor header MX2 #define SERVO2_PIN 24 // Motor header MX3 #define SERVO3_PIN 5 // PWM header pin 5 -#if ENABLED(Z_PROBE_SLED) - #define SLED_PIN -1 -#endif - -//Fan_2 2 - -/***************** -#if ENABLED(ULTRA_LCD) - - #define KILL_PIN -1 //was 80 Glen maybe a mistake - -#endif // ULTRA_LCD */ - -#if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define BEEPER_PIN 44 - // Pins for DOGM SPI LCD Support - #define DOGLCD_A0 70 - #define DOGLCD_CS 71 - #define LCD_SCREEN_ROT_180 - - #define SD_DETECT_PIN -1 // Pin 72 if using easy adapter board - - #if ENABLED(TEMP_STAT_LEDS) - #define STAT_LED_RED 22 - #define STAT_LED_BLUE 32 - #endif -#endif // VIKI2/miniVIKI +#define SLED_PIN -1 #define FILWIDTH_PIN 3 // ANALOG NUMBERING @@ -71,57 +47,81 @@ ************************************************/ #define LARGE_FLASH true -#define X_STEP_PIN 37 -#define X_DIR_PIN 48 -#define X_MIN_PIN 12 -#define X_MAX_PIN 24 -#define X_ENABLE_PIN 29 -#define X_MS1_PIN 40 -#define X_MS2_PIN 41 -#define Y_STEP_PIN 36 -#define Y_DIR_PIN 49 -#define Y_MIN_PIN 11 -#define Y_MAX_PIN 23 -#define Y_ENABLE_PIN 28 -#define Y_MS1_PIN 69 -#define Y_MS2_PIN 39 -#define Z_STEP_PIN 35 -#define Z_DIR_PIN 47 -#define Z_MIN_PIN 10 -#define Z_MAX_PIN 30 -#define Z_ENABLE_PIN 27 -#define Z_MS1_PIN 68 -#define Z_MS2_PIN 67 -#define HEATER_BED_PIN 3 -#define TEMP_BED_PIN 7 //2014/02/04 0:T0 / 1:T1 / 2:T2 / 7:T3 -#define HEATER_0_PIN 9 -#define TEMP_0_PIN 0 -#define HEATER_1_PIN 7 +// +// Limit Switches +// +#define X_MIN_PIN 12 +#define X_MAX_PIN 24 +#define Y_MIN_PIN 11 +#define Y_MAX_PIN 23 +#define Z_MIN_PIN 10 +#define Z_MAX_PIN 30 -#define E0_STEP_PIN 34 -#define E0_DIR_PIN 43 -#define E0_ENABLE_PIN 26 -#define E0_MS1_PIN 65 -#define E0_MS2_PIN 66 -#define E1_STEP_PIN 33 -#define E1_DIR_PIN 42 -#define E1_ENABLE_PIN 25 -#define E1_MS1_PIN 63 -#define E1_MS2_PIN 64 +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 30 +#endif -#define DIGIPOTSS_PIN 38 +// +// Steppers +// +#define X_STEP_PIN 37 +#define X_DIR_PIN 48 +#define X_ENABLE_PIN 29 +#define X_MS1_PIN 40 +#define X_MS2_PIN 41 + +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 49 +#define Y_ENABLE_PIN 28 +#define Y_MS1_PIN 69 +#define Y_MS2_PIN 39 + +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_ENABLE_PIN 27 +#define Z_MS1_PIN 68 +#define Z_MS2_PIN 67 + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 +#define E0_MS1_PIN 65 +#define E0_MS2_PIN 66 + +#define E1_STEP_PIN 33 +#define E1_DIR_PIN 42 +#define E1_ENABLE_PIN 25 +#define E1_MS1_PIN 63 +#define E1_MS2_PIN 64 + +#define DIGIPOTSS_PIN 38 #define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping +// +// Heaters / Fans +// +#define HEATER_0_PIN 9 +#define HEATER_1_PIN 7 +#define HEATER_BED_PIN 3 + +#define FAN_PIN 8 +#define FAN0_PIN 6 +#define FAN1_PIN 2 + +#define TEMP_0_PIN 0 +#define TEMP_BED_PIN 7 + #define SDSS 53 #define LED_PIN 13 -#define FAN_PIN 8 #define PS_ON_PIN 4 -#define FAN_0_PIN 6 //Glen -#define FAN_1_PIN 2 //Glen - -// 2015/12/23 +// +// LCD / Controller +// #define LCD_PINS_RS 70 //ext2_5 #define LCD_PINS_ENABLE 71 //ext2_7 #define LCD_PINS_D4 72 ///////Ext2 9 ? @@ -139,3 +139,18 @@ #define BTN_DOWN 85 //ext2_6 #define HOME_PIN BTN_HOME + +#if ENABLED(VIKI2) || ENABLED(miniVIKI) + #define BEEPER_PIN 44 + // Pins for DOGM SPI LCD Support + #define DOGLCD_A0 70 + #define DOGLCD_CS 71 + #define LCD_SCREEN_ROT_180 + + #define SD_DETECT_PIN -1 // Pin 72 if using easy adapter board + + #if ENABLED(TEMP_STAT_LEDS) + #define STAT_LED_RED 22 + #define STAT_LED_BLUE 32 + #endif +#endif // VIKI2/miniVIKI diff --git a/Marlin/pins_AZTEEG_X3_PRO.h b/Marlin/pins_AZTEEG_X3_PRO.h index f4114c568d..4bc575a333 100644 --- a/Marlin/pins_AZTEEG_X3_PRO.h +++ b/Marlin/pins_AZTEEG_X3_PRO.h @@ -28,21 +28,16 @@ #include "pins_RAMPS.h" -#undef FAN_PIN -#define FAN_PIN 6 //Part Cooling System - -#undef BEEPER_PIN -#define BEEPER_PIN 33 -#define CONTROLLERFAN_PIN 4 //Pin used for the fan to cool motherboard (-1 to disable) -//Fans/Water Pump to cool the hotend cool side. -#define EXTRUDER_0_AUTO_FAN_PIN 5 -#define EXTRUDER_1_AUTO_FAN_PIN 5 -#define EXTRUDER_2_AUTO_FAN_PIN 5 -#define EXTRUDER_3_AUTO_FAN_PIN 5 // -//This section is to swap the MIN and MAX pins because the X3 Pro comes with only -//MIN endstops soldered onto the board. Delta code wants the homing endstops to be -//the MAX so I swapped them here. +// Tested this pin with bed leveling on a Delta with 1 servo. +// Physical wire attachment on EXT1: GND, 5V, D47. +// +#undef SERVO0_PIN +#define SERVO0_PIN 47 + +// +// Swap the MIN and MAX endstop pins because the X3 Pro comes with only +// MIN endstop pin headers soldered onto the board. // #if ENABLED(DELTA) #undef X_MIN_PIN @@ -60,10 +55,16 @@ #define Z_MAX_PIN 18 #endif +// +// Z Probe (when not Z_MIN_PIN) +// #ifndef Z_MIN_PROBE_PIN - #define Z_MIN_PROBE_PIN 19 + #define Z_MIN_PROBE_PIN 18 #endif +// +// Steppers +// #define E2_STEP_PIN 23 #define E2_DIR_PIN 25 #define E2_ENABLE_PIN 40 @@ -76,19 +77,9 @@ #define E4_DIR_PIN 37 #define E4_ENABLE_PIN 42 -#undef HEATER_1_PIN -#undef HEATER_2_PIN -#undef HEATER_3_PIN -#define HEATER_1_PIN 9 -#define HEATER_2_PIN 16 -#define HEATER_3_PIN 17 -#define HEATER_4_PIN 4 -#define HEATER_5_PIN 5 -#define HEATER_6_PIN 6 -#define HEATER_7_PIN 11 - -#undef TEMP_2_PIN -#undef TEMP_3_PIN +// +// Temperature Sensors +// #define TEMP_2_PIN 12 // ANALOG NUMBERING #define TEMP_3_PIN 11 // ANALOG NUMBERING #define TEMP_4_PIN 10 // ANALOG NUMBERING @@ -96,17 +87,36 @@ #define TC2 5 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro // -// These Servo pins are for when they are defined. Tested for usage with bed leveling -// on a Delta with 1 servo. Running through the Z servo endstop in code. -// Physical wire attachment was done on EXT1 on the GND, 5V, and D47 pins. +// Heaters / Fans // -#undef SERVO0_PIN -#define SERVO0_PIN 47 +#define HEATER_2_PIN 16 +#define HEATER_3_PIN 17 +#define HEATER_4_PIN 4 +#define HEATER_5_PIN 5 +#define HEATER_6_PIN 6 +#define HEATER_7_PIN 11 + +#undef FAN_PIN +#define FAN_PIN 6 //Part Cooling System + +#define CONTROLLERFAN_PIN 4 //Pin used for the fan to cool motherboard (-1 to disable) + +// Fans/Water Pump to cool the hotend cool side. +#define EXTRUDER_0_AUTO_FAN_PIN 5 +#define EXTRUDER_1_AUTO_FAN_PIN 5 +#define EXTRUDER_2_AUTO_FAN_PIN 5 +#define EXTRUDER_3_AUTO_FAN_PIN 5 + +// +// LCD / Controller +// +#undef BEEPER_PIN +#define BEEPER_PIN 33 #if ENABLED(VIKI2) || ENABLED(miniVIKI) #undef SD_DETECT_PIN - #define SD_DETECT_PIN 49 // For easy adapter board -#elif ENABLED(TEMP_STAT_LEDS) - #define STAT_LED_RED 32 - #define STAT_LED_BLUE 35 + #define SD_DETECT_PIN 49 // For easy adapter board +#else + #define STAT_LED_RED 32 + #define STAT_LED_BLUE 35 #endif diff --git a/Marlin/pins_BRAINWAVE.h b/Marlin/pins_BRAINWAVE.h index 9dfeb3ab1f..a1006aec08 100644 --- a/Marlin/pins_BRAINWAVE.h +++ b/Marlin/pins_BRAINWAVE.h @@ -33,22 +33,29 @@ #define BOARD_NAME "Brainwave" +// +// Limit Switches +// +#define X_STOP_PIN 7 +#define Y_STOP_PIN 6 +#define Z_STOP_PIN 5 + +// +// Steppers +// #define X_STEP_PIN 27 #define X_DIR_PIN 29 #define X_ENABLE_PIN 28 -#define X_STOP_PIN 7 #define X_ATT_PIN 26 #define Y_STEP_PIN 31 #define Y_DIR_PIN 33 #define Y_ENABLE_PIN 32 -#define Y_STOP_PIN 6 #define Y_ATT_PIN 30 #define Z_STEP_PIN 17 #define Z_DIR_PIN 19 #define Z_ENABLE_PIN 18 -#define Z_STOP_PIN 5 #define Z_ATT_PIN 16 #define E0_STEP_PIN 21 @@ -56,11 +63,17 @@ #define E0_ENABLE_PIN 22 #define E0_ATT_PIN 20 +// +// Temperature Sensors +// +#define TEMP_0_PIN 7 // Extruder / Analog pin numbering +#define TEMP_BED_PIN 6 // Bed / Analog pin numbering + +// +// Heaters / Fans +// #define HEATER_0_PIN 4 // Extruder #define HEATER_BED_PIN 38 // Bed #define FAN_PIN 3 // Fan -#define TEMP_0_PIN 7 // Extruder / Analog pin numbering -#define TEMP_BED_PIN 6 // Bed / Analog pin numbering - #define LED_PIN 39 diff --git a/Marlin/pins_BRAINWAVE_PRO.h b/Marlin/pins_BRAINWAVE_PRO.h index b0d53a0ca9..f263f1bc67 100644 --- a/Marlin/pins_BRAINWAVE_PRO.h +++ b/Marlin/pins_BRAINWAVE_PRO.h @@ -41,13 +41,23 @@ #define LARGE_FLASH true +// +// Limit Switches +// #define X_STOP_PIN 47 #define Y_STOP_PIN 18 #define Z_MAX_PIN 36 + +// +// Z Probe (when not Z_MIN_PIN) +// #ifndef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN 17 #endif +// +// Steppers +// #define X_STEP_PIN 33 #define X_DIR_PIN 32 #define X_ENABLE_PIN 11 @@ -64,14 +74,24 @@ #define E0_DIR_PIN 34 #define E0_ENABLE_PIN 13 -#define HEATER_0_PIN 15 -#define HEATER_BED_PIN 14 // Bed -#define FAN_PIN 16 // Fan, PWM - +// +// Temperature Sensors +// #define TEMP_0_PIN 2 // Extruder / Analog pin numbering #define TEMP_1_PIN 1 // Spare / Analog pin numbering #define TEMP_BED_PIN 0 // Bed / Analog pin numbering +// +// Heaters / Fans +// +#define HEATER_0_PIN 15 +#define HEATER_BED_PIN 14 // Bed +#define FAN_PIN 16 // Fan, PWM + +// +// LCD / Controller +// #define SDSS 20 -#define LED_PIN 19 #define SD_DETECT_PIN 12 + +#define LED_PIN 19 diff --git a/Marlin/pins_CHEAPTRONIC.h b/Marlin/pins_CHEAPTRONIC.h index 2fbb4e8356..a330e3742c 100644 --- a/Marlin/pins_CHEAPTRONIC.h +++ b/Marlin/pins_CHEAPTRONIC.h @@ -31,57 +31,59 @@ #define BOARD_NAME "Cheaptronic v1.0" #define LARGE_FLASH true -// X motor stepper -#define X_STEP_PIN 14 -#define X_DIR_PIN 15 -#define X_ENABLE_PIN 24 +// +// Limit Switches +// +#define X_STOP_PIN 3 +#define Y_STOP_PIN 2 +#define Z_STOP_PIN 5 -// Y motor stepper -#define Y_STEP_PIN 35 -#define Y_DIR_PIN 36 -#define Y_ENABLE_PIN 31 +// +// Steppers +// +#define X_STEP_PIN 14 +#define X_DIR_PIN 15 +#define X_ENABLE_PIN 24 -// Z motor stepper -#define Z_STEP_PIN 40 -#define Z_DIR_PIN 41 -#define Z_ENABLE_PIN 37 +#define Y_STEP_PIN 35 +#define Y_DIR_PIN 36 +#define Y_ENABLE_PIN 31 -// XYZ endstops -#define X_STOP_PIN 3 -#define Y_STOP_PIN 2 -#define Z_STOP_PIN 5 +#define Z_STEP_PIN 40 +#define Z_DIR_PIN 41 +#define Z_ENABLE_PIN 37 -// Extruder 0 stepper -#define E0_STEP_PIN 26 -#define E0_DIR_PIN 28 -#define E0_ENABLE_PIN 25 +#define E0_STEP_PIN 26 +#define E0_DIR_PIN 28 +#define E0_ENABLE_PIN 25 -// Extruder 1 stepper -#define E1_STEP_PIN 33 -#define E1_DIR_PIN 34 -#define E1_ENABLE_PIN 30 - - -#define HEATER_0_PIN 19 // EXTRUDER 1 -#define HEATER_1_PIN 23 // EXTRUDER 2 -#define HEATER_BED_PIN 22 +#define E1_STEP_PIN 33 +#define E1_DIR_PIN 34 +#define E1_ENABLE_PIN 30 +// // Temperature sensors -#define TEMP_0_PIN 15 -#define TEMP_1_PIN 14 -#define TEMP_BED_PIN 13 +// +#define TEMP_0_PIN 15 +#define TEMP_1_PIN 14 +#define TEMP_BED_PIN 13 + +// +// Heaters / Fans +// +#define HEATER_0_PIN 19 // EXTRUDER 1 +#define HEATER_1_PIN 23 // EXTRUDER 2 +#define HEATER_BED_PIN 22 // Cheaptronic v1.0 doesn't support LCD -#define LCD_PINS_RS -1 -#define LCD_PINS_ENABLE -1 -#define LCD_PINS_D4 -1 -#define LCD_PINS_D5 -1 -#define LCD_PINS_D6 -1 -#define LCD_PINS_D7 -1 +#define LCD_PINS_RS -1 +#define LCD_PINS_ENABLE -1 +#define LCD_PINS_D4 -1 +#define LCD_PINS_D5 -1 +#define LCD_PINS_D6 -1 +#define LCD_PINS_D7 -1 // Cheaptronic v1.0 doesn't support keypad -#define BTN_EN1 -1 -#define BTN_EN2 -1 -#define BTN_ENC -1 - -// Cheaptronic v1.0 doesn't use this +#define BTN_EN1 -1 +#define BTN_EN2 -1 +#define BTN_ENC -1 diff --git a/Marlin/pins_CNCONTROLS_11.h b/Marlin/pins_CNCONTROLS_11.h index 1de35a2c17..174fb1634f 100644 --- a/Marlin/pins_CNCONTROLS_11.h +++ b/Marlin/pins_CNCONTROLS_11.h @@ -6,54 +6,65 @@ #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. #endif -#define BOARD_NAME "CN Controls V11" +#define BOARD_NAME "CN Controls V11" //#define LARGE_FLASH true -#define X_ENABLE_PIN 35 -#define X_STEP_PIN 34 -#define X_DIR_PIN 36 -#define X_MIN_PIN 43 -#define X_MAX_PIN -1 +// +// Limit Switches +// +#define X_STOP_PIN 43 +#define Y_STOP_PIN 45 +#define Z_STOP_PIN 42 -#define Y_ENABLE_PIN 38 -#define Y_STEP_PIN 37 -#define Y_DIR_PIN 39 -#define Y_MIN_PIN 45 -#define Y_MAX_PIN -1 +// +// Steppers +// +#define X_STEP_PIN 34 +#define X_DIR_PIN 36 +#define X_ENABLE_PIN 35 -#define Z_ENABLE_PIN 41 -#define Z_STEP_PIN 40 -#define Z_DIR_PIN 48 -#define Z_MIN_PIN 42 -#define Z_MAX_PIN -1 +#define Y_STEP_PIN 37 +#define Y_DIR_PIN 39 +#define Y_ENABLE_PIN 38 -#define E0_ENABLE_PIN 3 -#define E0_STEP_PIN 29 -#define E0_DIR_PIN 28 -#define HEATER_0_PIN 5 -#define TEMP_0_PIN 0 // ANALOG INPUT !! +#define Z_STEP_PIN 40 +#define Z_DIR_PIN 48 +#define Z_ENABLE_PIN 41 -#define E1_ENABLE_PIN 60 -#define E1_STEP_PIN 61 -#define E1_DIR_PIN 62 -#define HEATER_1_PIN 58 -#define TEMP_1_PIN 3 // 3 for tool2 -> 2 for chambertemp +#define E0_STEP_PIN 29 +#define E0_DIR_PIN 28 +#define E0_ENABLE_PIN 3 -#define E2_ENABLE_PIN 16 -#define E2_STEP_PIN 15 -#define E2_DIR_PIN 14 -#define HEATER_2_PIN 64 -#define TEMP_2_PIN 2 // 9 for tool3 -> 2 for chambertemp +#define E1_STEP_PIN 61 +#define E1_DIR_PIN 62 +#define E1_ENABLE_PIN 60 -#define E3_ENABLE_PIN 47 -#define E3_STEP_PIN 44 -#define E3_DIR_PIN 49 -#define HEATER_3_PIN 46 -#define TEMP_3_PIN 11 // 11 for tool4 -> 2 for chambertemp +#define E2_STEP_PIN 15 +#define E2_DIR_PIN 14 +#define E2_ENABLE_PIN 16 -#define HEATER_BED_PIN 2 -#define TEMP_BED_PIN 1 // ANALOG INPUT !! +#define E3_STEP_PIN 44 +#define E3_DIR_PIN 49 +#define E3_ENABLE_PIN 47 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // ANALOG INPUT !! +#define TEMP_1_PIN 3 // 3 for tool2 -> 2 for chambertemp +#define TEMP_2_PIN 2 // 9 for tool3 -> 2 for chambertemp +#define TEMP_3_PIN 11 // 11 for tool4 -> 2 for chambertemp +#define TEMP_BED_PIN 1 // ANALOG INPUT !! + +// +// Heaters / Fans +// +#define HEATER_0_PIN 5 +#define HEATER_1_PIN 58 +#define HEATER_2_PIN 64 +#define HEATER_3_PIN 46 +#define HEATER_BED_PIN 2 // Tools @@ -72,30 +83,37 @@ //#define SPARE_IO 12 //#define FAN_PIN 7 // common PWM pin for all tools -// User interface -#define BEEPER_PIN 6 +// +// SD Card +// +#define SDSS 53 +#define SD_DETECT_PIN 13 + +// +// LCD / Controller +// +#define BEEPER_PIN 6 // Pins for DOGM SPI LCD Support -#define DOGLCD_A0 26 -#define DOGLCD_CS 24 -#define DOGLCD_MOSI -1 -#define DOGLCD_SCK -1 +#define DOGLCD_A0 26 +#define DOGLCD_CS 24 +#define DOGLCD_MOSI -1 +#define DOGLCD_SCK -1 -// The encoder and click button -#define BTN_EN1 23 -#define BTN_EN2 25 -#define BTN_ENC 27 +#define BTN_EN1 23 +#define BTN_EN2 25 +#define BTN_ENC 27 // Hardware buttons for manual movement of XYZ -#define SHIFT_OUT 19 -#define SHIFT_LD 18 -#define SHIFT_CLK 17 +#define SHIFT_OUT 19 +#define SHIFT_LD 18 +#define SHIFT_CLK 17 -//#define UI1 31 -//#define UI2 22 +//#define UI1 31 +//#define UI2 22 -// Other -#define SDSS 53 -#define SD_DETECT_PIN 13 -#define STAT_LED_BLUE -1 -#define STAT_LED_RED 31 +// +// Misc. Functions +// +#define STAT_LED_BLUE -1 +#define STAT_LED_RED 31 diff --git a/Marlin/pins_CNCONTROLS_12.h b/Marlin/pins_CNCONTROLS_12.h index cb338346d9..c3d6945898 100644 --- a/Marlin/pins_CNCONTROLS_12.h +++ b/Marlin/pins_CNCONTROLS_12.h @@ -10,96 +10,115 @@ //#define LARGE_FLASH true -#define X_ENABLE_PIN 26 -#define X_STEP_PIN 25 -#define X_DIR_PIN 27 -#define X_MIN_PIN 19 -#define X_MAX_PIN -1 +// +// Limit Switches +// +#define X_STOP_PIN 19 +#define Y_STOP_PIN 22 +#define Z_STOP_PIN 23 -#define Y_ENABLE_PIN 29 -#define Y_STEP_PIN 28 -#define Y_DIR_PIN 30 -#define Y_MIN_PIN 22 -#define Y_MAX_PIN -1 +// +// Steppers +// +#define X_STEP_PIN 25 +#define X_DIR_PIN 27 +#define X_ENABLE_PIN 26 -#define Z_ENABLE_PIN 32 -#define Z_STEP_PIN 31 -#define Z_DIR_PIN 33 -#define Z_MIN_PIN 23 -#define Z_MAX_PIN -1 +#define Y_STEP_PIN 28 +#define Y_DIR_PIN 30 +#define Y_ENABLE_PIN 29 -#define E0_ENABLE_PIN 58 -#define E0_STEP_PIN 57 -#define E0_DIR_PIN 55 -#define HEATER_0_PIN 11 -#define TEMP_0_PIN 0 // ANALOG INPUT !! +#define Z_STEP_PIN 31 +#define Z_DIR_PIN 33 +#define Z_ENABLE_PIN 32 -#define E1_ENABLE_PIN 60 -#define E1_STEP_PIN 61 -#define E1_DIR_PIN 62 -#define HEATER_1_PIN 9 -#define TEMP_1_PIN 9 // 9 for tool2 -> 13 for chambertemp +#define E0_STEP_PIN 57 +#define E0_DIR_PIN 55 +#define E0_ENABLE_PIN 58 -#define E2_ENABLE_PIN 44 -#define E2_STEP_PIN 46 -#define E2_DIR_PIN 66 -#define HEATER_2_PIN 6 -#define TEMP_2_PIN 13 // 10 for tool3 -> 13 for chambertemp +#define E1_STEP_PIN 61 +#define E1_DIR_PIN 62 +#define E1_ENABLE_PIN 60 -#define E3_ENABLE_PIN 47 -#define E3_STEP_PIN 45 -#define E3_DIR_PIN 69 -#define HEATER_3_PIN 3 -#define TEMP_3_PIN 11 // 11 for tool4 -> 13 for chambertemp +#define E2_STEP_PIN 46 +#define E2_DIR_PIN 66 +#define E2_ENABLE_PIN 44 -#define HEATER_BED_PIN 24 -#define TEMP_BED_PIN 14 // ANALOG INPUT !! +#define E3_STEP_PIN 45 +#define E3_DIR_PIN 69 +#define E3_ENABLE_PIN 47 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // ANALOG INPUT !! +#define TEMP_1_PIN 9 // 9 for tool2 -> 13 for chambertemp +#define TEMP_2_PIN 13 // 10 for tool3 -> 13 for chambertemp +#define TEMP_3_PIN 11 // 11 for tool4 -> 13 for chambertemp +#define TEMP_BED_PIN 14 // ANALOG INPUT !! +//#define TEMP_CHAMBER_PIN 13 // ANALOG INPUT !! + +// +// Heaters / Fans +// +#define HEATER_0_PIN 11 +#define HEATER_1_PIN 9 +#define HEATER_2_PIN 6 +#define HEATER_3_PIN 3 +#define HEATER_BED_PIN 24 + +#define FAN_PIN 5 // 5 is PWMtool3 -> 7 is common PWM pin for all tools + +//#define PWM_1_PIN 12 +//#define PWM_2_PIN 13 +//#define SPARE_IO 17 // Tools -//#define TOOL_0_PIN 56 -//#define TOOL_0_PWM_PIN 10 // red warning led at dual extruder -//#define TOOL_1_PIN 59 -//#define TOOL_1_PWM_PIN 8 // lights at dual extruder -//#define TOOL_2_PIN 4 -//#define TOOL_2_PWM_PIN 5 -//#define TOOL_3_PIN 14 -//#define TOOL_3_PWM_PIN 2 +//#define TOOL_0_PIN 56 +//#define TOOL_0_PWM_PIN 10 // red warning led at dual extruder +//#define TOOL_1_PIN 59 +//#define TOOL_1_PWM_PIN 8 // lights at dual extruder +//#define TOOL_2_PIN 4 +//#define TOOL_2_PWM_PIN 5 +//#define TOOL_3_PIN 14 +//#define TOOL_3_PWM_PIN 2 // Common I/O -//#define TEMP_CHAMBER_PIN 13 // ANALOG INPUT !! -#define FIL_RUNOUT_PIN 18 -//#define PWM_1_PIN 12 -//#define PWM_2_PIN 13 -//#define SPARE_IO 17 -#define FAN_PIN 5 // 5 is PWMtool3 -> 7 is common PWM pin for all tools - -// User interface -#define BEEPER_PIN 16 +// +// LCD / Controller +// +#define BEEPER_PIN 16 // Pins for DOGM SPI LCD Support -#define DOGLCD_A0 39 -#define DOGLCD_CS 35 -#define DOGLCD_MOSI 48 -#define DOGLCD_SCK 49 +#define DOGLCD_A0 39 +#define DOGLCD_CS 35 +#define DOGLCD_MOSI 48 +#define DOGLCD_SCK 49 #define LCD_SCREEN_ROT_180 // The encoder and click button -#define BTN_EN1 36 -#define BTN_EN2 34 -#define BTN_ENC 38 +#define BTN_EN1 36 +#define BTN_EN2 34 +#define BTN_ENC 38 // Hardware buttons for manual movement of XYZ -#define SHIFT_OUT 42 -#define SHIFT_LD 41 -#define SHIFT_CLK 40 +#define SHIFT_OUT 42 +#define SHIFT_LD 41 +#define SHIFT_CLK 40 -//#define UI1 43 -//#define UI2 37 +//#define UI1 43 +//#define UI2 37 + +#define STAT_LED_BLUE -1 +#define STAT_LED_RED 10 // TOOL_0_PWM_PIN + +// +// SD Card +// +#define SDSS 53 +#define SD_DETECT_PIN 15 // Other -#define SDSS 53 -#define SD_DETECT_PIN 15 -#define STAT_LED_BLUE -1 -#define STAT_LED_RED 10 // TOOL_0_PWM_PIN +#define FIL_RUNOUT_PIN 18 diff --git a/Marlin/pins_ELEFU_3.h b/Marlin/pins_ELEFU_3.h index 2b8e64d8e5..55263077bb 100644 --- a/Marlin/pins_ELEFU_3.h +++ b/Marlin/pins_ELEFU_3.h @@ -28,58 +28,82 @@ #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #endif -#define BOARD_NAME "Elefu Ra v3" +#define BOARD_NAME "Elefu Ra v3" +// +// Limit Switches +// +#define X_MIN_PIN 35 +#define X_MAX_PIN 34 +#define Y_MIN_PIN 33 +#define Y_MAX_PIN 32 +#define Z_MIN_PIN 31 +#define Z_MAX_PIN 30 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 30 +#endif + +// +// Steppers +// #define X_STEP_PIN 49 #define X_DIR_PIN 13 #define X_ENABLE_PIN 48 -#define X_MIN_PIN 35 -#define X_MAX_PIN 34 #define Y_STEP_PIN 11 #define Y_DIR_PIN 9 #define Y_ENABLE_PIN 12 -#define Y_MIN_PIN 33 -#define Y_MAX_PIN 32 #define Z_STEP_PIN 7 #define Z_DIR_PIN 6 #define Z_ENABLE_PIN 8 -#define Z_MIN_PIN 31 -#define Z_MAX_PIN 30 - -#define E2_STEP_PIN 43 -#define E2_DIR_PIN 47 -#define E2_ENABLE_PIN 42 - -#define E1_STEP_PIN 18 -#define E1_DIR_PIN 19 -#define E1_ENABLE_PIN 38 #define E0_STEP_PIN 40 #define E0_DIR_PIN 41 #define E0_ENABLE_PIN 37 -#define FAN_PIN 16 //5V PWM +#define E1_STEP_PIN 18 +#define E1_DIR_PIN 19 +#define E1_ENABLE_PIN 38 -#define PS_ON_PIN 10 //Set to -1 if using a manual switch on the PWRSW Connector -#define SLEEP_WAKE_PIN 26 //This feature still needs work +#define E2_STEP_PIN 43 +#define E2_DIR_PIN 47 +#define E2_ENABLE_PIN 42 -#define HEATER_0_PIN 45 //12V PWM1 -#define HEATER_1_PIN 46 //12V PWM2 -#define HEATER_2_PIN 17 //12V PWM3 -#define HEATER_BED_PIN 44 //DOUBLE 12V PWM -#define TEMP_0_PIN 3 //ANALOG NUMBERING -#define TEMP_1_PIN 2 //ANALOG NUMBERING -#define TEMP_2_PIN 1 //ANALOG NUMBERING -#define TEMP_BED_PIN 0 //ANALOG NUMBERING +// +// Temperature Sensors +// +#define TEMP_0_PIN 3 // ANALOG NUMBERING +#define TEMP_1_PIN 2 // ANALOG NUMBERING +#define TEMP_2_PIN 1 // ANALOG NUMBERING +#define TEMP_BED_PIN 0 // ANALOG NUMBERING -#define BEEPER_PIN 36 +// +// Heaters / Fans +// +#define HEATER_0_PIN 45 // 12V PWM1 +#define HEATER_1_PIN 46 // 12V PWM2 +#define HEATER_2_PIN 17 // 12V PWM3 +#define HEATER_BED_PIN 44 // DOUBLE 12V PWM -// M240 Triggers a camera by emulating a Canon RC-1 Remote -// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ +#define FAN_PIN 16 // 5V PWM + +// +// Misc. Functions +// +#define PS_ON_PIN 10 // Set to -1 if using a manual switch on the PWRSW Connector +#define SLEEP_WAKE_PIN 26 // This feature still needs work #define PHOTOGRAPH_PIN 29 +// +// LCD / Controller +// +#define BEEPER_PIN 36 + #if ENABLED(RA_CONTROL_PANEL) #define SDSS 53 diff --git a/Marlin/pins_GEN3_MONOLITHIC.h b/Marlin/pins_GEN3_MONOLITHIC.h index 85d5b3faef..aa907bedfa 100644 --- a/Marlin/pins_GEN3_MONOLITHIC.h +++ b/Marlin/pins_GEN3_MONOLITHIC.h @@ -31,39 +31,45 @@ #define BOARD_NAME "Gen3 Monolithic" #define DEBUG_PIN 0 -// x axis -#define X_STEP_PIN 15 -#define X_DIR_PIN 18 -#define X_MIN_PIN 20 -// Alex Checar #define X_STOP_PIN 20 -#define X_ENABLE_PIN 24 // actually uses Y_enable_pin -#define X_MAX_PIN -1 +// +// Limit Switches +// +#define X_STOP_PIN 20 +#define Y_STOP_PIN 25 +#define Z_STOP_PIN 30 -// y axis -#define Y_STEP_PIN 23 -#define Y_DIR_PIN 22 -#define Y_MIN_PIN 25 -// Alex Checar #define Y_STOP_PIN 25 -#define Y_ENABLE_PIN 24 // shared with X_enable_pin -#define Y_MAX_PIN -1 +// +// Steppers +// +#define X_STEP_PIN 15 +#define X_DIR_PIN 18 +#define X_ENABLE_PIN 24 // actually uses Y_enable_pin -// z axis -#define Z_STEP_PIN 27 -#define Z_DIR_PIN 28 -#define Z_MIN_PIN 30 -// Alex Checar #define Z_STOP_PIN 30 -#define Z_ENABLE_PIN 29 -#define Z_MAX_PIN -1 +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 // shared with X_enable_pin -// extruder pins -#define E0_STEP_PIN 12 -#define E0_DIR_PIN 17 +#define Z_STEP_PIN 27 +#define Z_DIR_PIN 28 +#define Z_ENABLE_PIN 29 + +#define E0_STEP_PIN 12 +#define E0_DIR_PIN 17 #define E0_ENABLE_PIN 3 -#define HEATER_0_PIN 16 -#define TEMP_0_PIN 0 +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 -// pin for controlling the PSU. -#define PS_ON_PIN 14 // Alex, Do this work on the card? +// +// Heaters +// +#define HEATER_0_PIN 16 + +// +// Etc. +// +#define PS_ON_PIN 14 // Alex, does this work on the card? // Alex extras from Gen3+ diff --git a/Marlin/pins_GEN3_PLUS.h b/Marlin/pins_GEN3_PLUS.h index 7889a0103e..3f6c9bfdf3 100644 --- a/Marlin/pins_GEN3_PLUS.h +++ b/Marlin/pins_GEN3_PLUS.h @@ -30,31 +30,47 @@ #define BOARD_NAME "Gen3+" +// +// Limit Switches +// +#define X_STOP_PIN 20 +#define Y_STOP_PIN 25 +#define Z_STOP_PIN 30 + +// +// Steppers +// #define X_STEP_PIN 15 #define X_DIR_PIN 18 -#define X_STOP_PIN 20 +#define X_ENABLE_PIN 19 #define Y_STEP_PIN 23 #define Y_DIR_PIN 22 -#define Y_STOP_PIN 25 +#define Y_ENABLE_PIN 24 #define Z_STEP_PIN 27 #define Z_DIR_PIN 28 -#define Z_STOP_PIN 30 +#define Z_ENABLE_PIN 29 #define E0_STEP_PIN 17 #define E0_DIR_PIN 21 - -#define PS_ON_PIN 14 - -#define HEATER_0_PIN 12 // (extruder) - -#define HEATER_BED_PIN 16 // (bed) -#define X_ENABLE_PIN 19 -#define Y_ENABLE_PIN 24 -#define Z_ENABLE_PIN 29 #define E0_ENABLE_PIN 13 -#define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder) -#define TEMP_BED_PIN 5 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed) -#define SDSS 4 +#define PS_ON_PIN 14 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // ANALOG INPUT (pin 33 extruder) +#define TEMP_BED_PIN 5 // ANALOG INPUT (pin 34 bed) + +// +// Heaters +// +#define HEATER_0_PIN 12 +#define HEATER_BED_PIN 16 + +// +// SD Card +// +#define SDSS 4 diff --git a/Marlin/pins_GEN6.h b/Marlin/pins_GEN6.h index ae3d33a9ad..530967e1c0 100644 --- a/Marlin/pins_GEN6.h +++ b/Marlin/pins_GEN6.h @@ -34,42 +34,57 @@ #define BOARD_NAME "Gen6" #endif -//x axis pins -#define X_STEP_PIN 15 -#define X_DIR_PIN 18 -#define X_ENABLE_PIN 19 -#define X_STOP_PIN 20 +// +// Limit Switches +// +#define X_STOP_PIN 20 +#define Y_STOP_PIN 25 +#define Z_STOP_PIN 30 -//y axis pins -#define Y_STEP_PIN 23 -#define Y_DIR_PIN 22 -#define Y_ENABLE_PIN 24 -#define Y_STOP_PIN 25 +// +// Steppers +// +#define X_STEP_PIN 15 +#define X_DIR_PIN 18 +#define X_ENABLE_PIN 19 -//z axis pins -#define Z_STEP_PIN 27 -#define Z_DIR_PIN 28 -#define Z_ENABLE_PIN 29 -#define Z_STOP_PIN 30 +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 -//extruder pins -#define E0_STEP_PIN 4 //Edited @ EJE Electronics 20100715 -#define E0_DIR_PIN 2 //Edited @ EJE Electronics 20100715 -#define E0_ENABLE_PIN 3 //Added @ EJE Electronics 20100715 -#define TEMP_0_PIN 5 //changed @ rkoeppl 20110410 +#define Z_STEP_PIN 27 +#define Z_DIR_PIN 28 +#define Z_ENABLE_PIN 29 -#define HEATER_0_PIN 14 //changed @ rkoeppl 20110410 +#define E0_STEP_PIN 4 //Edited @ EJE Electronics 20100715 +#define E0_DIR_PIN 2 //Edited @ EJE Electronics 20100715 +#define E0_ENABLE_PIN 3 //Added @ EJE Electronics 20100715 + +// +// Temperature Sensor +// +#define TEMP_0_PIN 5 //changed @ rkoeppl 20110410 + +// +// Heaters +// +#define HEATER_0_PIN 14 //changed @ rkoeppl 20110410 #if !MB(GEN6) - #define HEATER_BED_PIN 1 //changed @ rkoeppl 20110410 - #define TEMP_BED_PIN 0 //changed @ rkoeppl 20110410 + #define HEATER_BED_PIN 1 //changed @ rkoeppl 20110410 + #define TEMP_BED_PIN 0 //changed @ rkoeppl 20110410 #endif -#define SDSS 17 -//our pin for debugging. +// +// SD Card +// +#define SDSS 17 -#define DEBUG_PIN 0 +// +// Misc. Functions +// +#define DEBUG_PIN 0 -//our RS485 pins -#define TX_ENABLE_PIN 12 -#define RX_ENABLE_PIN 13 +// RS485 pins +#define TX_ENABLE_PIN 12 +#define RX_ENABLE_PIN 13 diff --git a/Marlin/pins_GEN7_12.h b/Marlin/pins_GEN7_12.h index 1e59ae6fa9..951641f611 100644 --- a/Marlin/pins_GEN7_12.h +++ b/Marlin/pins_GEN7_12.h @@ -36,52 +36,68 @@ #define GEN7_VERSION 12 // v1.x #endif -//x axis pins -#define X_STEP_PIN 19 -#define X_DIR_PIN 18 -#define X_ENABLE_PIN 24 -#define X_STOP_PIN 7 +// +// Limit Switches +// +#define X_STOP_PIN 7 +#define Y_STOP_PIN 5 +#define Z_MIN_PIN 1 +#define Z_MAX_PIN 0 -//y axis pins -#define Y_STEP_PIN 23 -#define Y_DIR_PIN 22 -#define Y_ENABLE_PIN 24 -#define Y_STOP_PIN 5 - -//z axis pins -#define Z_STEP_PIN 26 -#define Z_DIR_PIN 25 -#define Z_ENABLE_PIN 24 -#define Z_MIN_PIN 1 -#define Z_MAX_PIN 0 - -//extruder pins -#define E0_STEP_PIN 28 -#define E0_DIR_PIN 27 -#define E0_ENABLE_PIN 24 - -#define TEMP_0_PIN 1 -#define TEMP_BED_PIN 2 - -#define HEATER_0_PIN 4 -#define HEATER_BED_PIN 3 - - -// Gen7 v1.3 removed the fan pin -#if GEN7_VERSION < 13 - #define FAN_PIN 31 +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 0 #endif -#define PS_ON_PIN 15 +// +// Steppers +// +#define X_STEP_PIN 19 +#define X_DIR_PIN 18 +#define X_ENABLE_PIN 24 -//All these generations of Gen7 supply thermistor power -//via PS_ON, so ignore bad thermistor readings +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 + +#define Z_STEP_PIN 26 +#define Z_DIR_PIN 25 +#define Z_ENABLE_PIN 24 + +#define E0_STEP_PIN 28 +#define E0_DIR_PIN 27 +#define E0_ENABLE_PIN 24 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 1 +#define TEMP_BED_PIN 2 + +// +// Heaters / Fans +// +#define HEATER_0_PIN 4 +#define HEATER_BED_PIN 3 + +#if GEN7_VERSION < 13 // Gen7 v1.3 removed the fan pin + #define FAN_PIN 31 +#endif + +// +// Misc. Functions +// +#define PS_ON_PIN 15 + +// All these generations of Gen7 supply thermistor power +// via PS_ON, so ignore bad thermistor readings #define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE -//our pin for debugging. -#define DEBUG_PIN 0 +#define DEBUG_PIN 0 -//our RS485 pins -#define TX_ENABLE_PIN 12 -#define RX_ENABLE_PIN 13 +// RS485 pins +#define TX_ENABLE_PIN 12 +#define RX_ENABLE_PIN 13 diff --git a/Marlin/pins_LEAPFROG.h b/Marlin/pins_LEAPFROG.h index acfba03731..ece4d0febc 100644 --- a/Marlin/pins_LEAPFROG.h +++ b/Marlin/pins_LEAPFROG.h @@ -30,44 +30,63 @@ #define BOARD_NAME "Leapfrog" +// +// Limit Switches +// +#define X_MIN_PIN 47 +#define X_MAX_PIN 2 +#define Y_MIN_PIN 48 +#define Y_MAX_PIN 15 +#define Z_MIN_PIN 49 +#define Z_MAX_PIN -1 + +// +// Steppers +// #define X_STEP_PIN 28 #define X_DIR_PIN 63 #define X_ENABLE_PIN 29 -#define X_MIN_PIN 47 -#define X_MAX_PIN 2 //Max endstops default to disabled "-1", set to commented value to enable. #define Y_STEP_PIN 14 // A6 #define Y_DIR_PIN 15 // A0 #define Y_ENABLE_PIN 39 -#define Y_MIN_PIN 48 -#define Y_MAX_PIN 15 #define Z_STEP_PIN 31 // A2 #define Z_DIR_PIN 32 // A6 #define Z_ENABLE_PIN 30 // A1 -#define Z_MIN_PIN 49 -#define Z_MAX_PIN -1 -#define E0_STEP_PIN 34 //34 -#define E0_DIR_PIN 35 //35 -#define E0_ENABLE_PIN 33 //33 +#define E0_STEP_PIN 34 // 34 +#define E0_DIR_PIN 35 // 35 +#define E0_ENABLE_PIN 33 // 33 -#define E1_STEP_PIN 37 //37 -#define E1_DIR_PIN 40 //40 -#define E1_ENABLE_PIN 36 //36 +#define E1_STEP_PIN 37 // 37 +#define E1_DIR_PIN 40 // 40 +#define E1_ENABLE_PIN 36 // 36 +// +// Misc. Functions +// #define SDSS 11 #define LED_PIN 13 -#define FAN_PIN 7 -#define SOL1_PIN 16 -#define SOL2_PIN 17 +#define SOL1_PIN 16 +#define SOL2_PIN 17 -#define HEATER_0_PIN 9 -#define HEATER_1_PIN 8 // 12 -#define HEATER_2_PIN 11 //-1 // 13 +// +// Temperature Sensors +// #define TEMP_0_PIN 13 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_1_PIN 15 // 1 -#define HEATER_BED_PIN 10 // 14/15 #define TEMP_BED_PIN 14 // 1,2 or I2C + +// +// Heaters / Fans +// +#define HEATER_0_PIN 9 +#define HEATER_1_PIN 8 // 12 +#define HEATER_2_PIN 11 // 13 +#define HEATER_BED_PIN 10 // 14/15 + +#define FAN_PIN 7 + /* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */ diff --git a/Marlin/pins_MEGACONTROLLER.h b/Marlin/pins_MEGACONTROLLER.h index 7ea4ee34b7..2828842674 100644 --- a/Marlin/pins_MEGACONTROLLER.h +++ b/Marlin/pins_MEGACONTROLLER.h @@ -34,79 +34,109 @@ #define BOARD_NAME "Mega Controller" -#define SERVO0_PIN 30 -#define SERVO1_PIN 31 -#define SERVO2_PIN 32 -#define SERVO3_PIN 33 +// +// Servos +// +#define SERVO0_PIN 30 +#define SERVO1_PIN 31 +#define SERVO2_PIN 32 +#define SERVO3_PIN 33 -#define X_STEP_PIN 62//A8 -#define X_DIR_PIN 63//A9 -#define X_ENABLE_PIN 61//A7 -#define X_MIN_PIN 43 -#define X_MAX_PIN 42 //Max endstops default to disabled "-1", set to commented value to enable. +// +// Limit Switches +// +#define X_MIN_PIN 43 +#define X_MAX_PIN 42 +#define Y_MIN_PIN 38 +#define Y_MAX_PIN 41 +#define Z_MIN_PIN 40 +#define Z_MAX_PIN 37 -#define Y_STEP_PIN 65 // A11 -#define Y_DIR_PIN 66 // A12 -#define Y_ENABLE_PIN 64//A10 -#define Y_MIN_PIN 38 -#define Y_MAX_PIN 41 +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 37 +#endif -#define Z_STEP_PIN 68 // A14 -#define Z_DIR_PIN 69 // A15 -#define Z_ENABLE_PIN 67 // A13 -#define Z_MIN_PIN 40 -#define Z_MAX_PIN 37 +// +// Steppers +// +#define X_STEP_PIN 62 // A8 +#define X_DIR_PIN 63 // A9 +#define X_ENABLE_PIN 61 // A7 -#define E0_STEP_PIN 23 -#define E0_DIR_PIN 24 -#define E0_ENABLE_PIN 22 +#define Y_STEP_PIN 65 // A11 +#define Y_DIR_PIN 66 // A12 +#define Y_ENABLE_PIN 64 // A10 -#define E1_STEP_PIN 26 -#define E1_DIR_PIN 27 -#define E1_ENABLE_PIN 25 +#define Z_STEP_PIN 68 // A14 +#define Z_DIR_PIN 69 // A15 +#define Z_ENABLE_PIN 67 // A13 -#define SDSS 53 -#define LED_PIN 13 +#define E0_STEP_PIN 23 +#define E0_DIR_PIN 24 +#define E0_ENABLE_PIN 22 -#define FAN_PIN 39 -#define FAN1_PIN 35 -#define FAN2_PIN 36 -#define FAN_SOFT_PWM -#define CONTROLLERFAN_PIN FAN2_PIN +#define E1_STEP_PIN 26 +#define E1_DIR_PIN 27 +#define E1_ENABLE_PIN 25 -#define HEATER_0_PIN 29 // EXTRUDER 1 -#define HEATER_1_PIN 34 // EXTRUDER 2 +// +// Misc. Functions +// +#define SDSS 53 +#define LED_PIN 13 +// +// Temperature Sensors +// #if TEMP_SENSOR_0 == -1 - #define TEMP_0_PIN 4 // ANALOG NUMBERING + #define TEMP_0_PIN 4 // ANALOG NUMBERING #else - #define TEMP_0_PIN 0 // ANALOG NUMBERING + #define TEMP_0_PIN 0 // ANALOG NUMBERING #endif #if TEMP_SENSOR_1 == -1 - #define TEMP_1_PIN 5 // ANALOG NUMBERING + #define TEMP_1_PIN 5 // ANALOG NUMBERING #else - #define TEMP_1_PIN 2 // ANALOG NUMBERING + #define TEMP_1_PIN 2 // ANALOG NUMBERING #endif -#define TEMP_2_PIN 3 // ANALOG NUMBERING - -#define HEATER_BED_PIN 28 // BED +#define TEMP_2_PIN 3 // ANALOG NUMBERING #if TEMP_SENSOR_BED == -1 - #define TEMP_BED_PIN 6 // ANALOG NUMBERING + #define TEMP_BED_PIN 6 // ANALOG NUMBERING #else - #define TEMP_BED_PIN 1 // ANALOG NUMBERING + #define TEMP_BED_PIN 1 // ANALOG NUMBERING #endif -#if ENABLED(MINIPANEL) - #define BEEPER_PIN 46 - // Pins for DOGM SPI LCD Support - #define DOGLCD_A0 47 - #define DOGLCD_CS 45 - #define LCD_PIN_BL 44 // backlight LED on PA3 +// +// Heaters / Fans +// +#define HEATER_0_PIN 29 +#define HEATER_1_PIN 34 +#define HEATER_BED_PIN 28 - #define KILL_PIN 12 +#define FAN_PIN 39 +#define FAN1_PIN 35 +#define FAN2_PIN 36 + +#define CONTROLLERFAN_PIN FAN2_PIN + +#define FAN_SOFT_PWM + +// +// LCD / Controller +// +#if ENABLED(MINIPANEL) + #define BEEPER_PIN 46 + // Pins for DOGM SPI LCD Support + #define DOGLCD_A0 47 + #define DOGLCD_CS 45 + #define LCD_PIN_BL 44 // backlight LED on PA3 + + #define KILL_PIN 12 // GLCD features //#define LCD_CONTRAST 190 // Uncomment screen orientation @@ -114,10 +144,10 @@ //#define LCD_SCREEN_ROT_180 //#define LCD_SCREEN_ROT_270 - #define BTN_EN1 48 - #define BTN_EN2 11 - #define BTN_ENC 10 + #define BTN_EN1 48 + #define BTN_EN2 11 + #define BTN_ENC 10 - #define SD_DETECT_PIN 49 + #define SD_DETECT_PIN 49 #endif // MINIPANEL diff --git a/Marlin/pins_MEGATRONICS.h b/Marlin/pins_MEGATRONICS.h index 1b95f525fc..893c6fc13b 100644 --- a/Marlin/pins_MEGATRONICS.h +++ b/Marlin/pins_MEGATRONICS.h @@ -31,23 +31,37 @@ #define BOARD_NAME "Megatronics" #define LARGE_FLASH true +// +// Limit Switches +// +#define X_MIN_PIN 41 +#define X_MAX_PIN 37 +#define Y_MIN_PIN 14 +#define Y_MAX_PIN 15 +#define Z_MIN_PIN 18 +#define Z_MAX_PIN 19 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 19 +#endif + +// +// Steppers +// #define X_STEP_PIN 26 #define X_DIR_PIN 28 #define X_ENABLE_PIN 24 -#define X_MIN_PIN 41 -#define X_MAX_PIN 37 #define Y_STEP_PIN 60 // A6 #define Y_DIR_PIN 61 // A7 #define Y_ENABLE_PIN 22 -#define Y_MIN_PIN 14 -#define Y_MAX_PIN 15 #define Z_STEP_PIN 54 // A0 #define Z_DIR_PIN 55 // A1 #define Z_ENABLE_PIN 56 // A2 -#define Z_MIN_PIN 18 -#define Z_MAX_PIN 19 #define E0_STEP_PIN 31 #define E0_DIR_PIN 32 @@ -57,16 +71,16 @@ #define E1_DIR_PIN 36 #define E1_ENABLE_PIN 30 +// +// Misc. Functions +// #define SDSS 53 #define LED_PIN 13 - -#define FAN_PIN 7 // IO pin. Buffer needed #define PS_ON_PIN 12 -#define HEATER_0_PIN 9 -#define HEATER_1_PIN 8 -#define HEATER_BED_PIN 10 // BED - +// +// Temperature Sensors +// #if TEMP_SENSOR_0 == -1 #define TEMP_0_PIN 8 // ANALOG NUMBERING #else @@ -75,7 +89,18 @@ #define TEMP_1_PIN 15 // ANALOG NUMBERING #define TEMP_BED_PIN 14 // ANALOG NUMBERING -// AUX-4 +// +// Heaters / Fans +// +#define HEATER_0_PIN 9 +#define HEATER_1_PIN 8 +#define HEATER_BED_PIN 10 + +#define FAN_PIN 7 // IO pin. Buffer needed + +// +// LCD / Controller +// #define BEEPER_PIN 33 #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) diff --git a/Marlin/pins_MEGATRONICS_2.h b/Marlin/pins_MEGATRONICS_2.h index 991ab4a9cc..ec0728052c 100644 --- a/Marlin/pins_MEGATRONICS_2.h +++ b/Marlin/pins_MEGATRONICS_2.h @@ -31,74 +31,101 @@ #define BOARD_NAME "Megatronics v2.0" #define LARGE_FLASH true -#define X_STEP_PIN 26 -#define X_DIR_PIN 27 -#define X_ENABLE_PIN 25 -#define X_MIN_PIN 37 -#define X_MAX_PIN 40 +// +// Limit Switches +// +#define X_MIN_PIN 37 +#define X_MAX_PIN 40 +#define Y_MIN_PIN 41 +#define Y_MAX_PIN 38 +#define Z_MIN_PIN 18 +#define Z_MAX_PIN 19 -#define Y_STEP_PIN 4 // A6 -#define Y_DIR_PIN 54 // A0 -#define Y_ENABLE_PIN 5 -#define Y_MIN_PIN 41 -#define Y_MAX_PIN 38 +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 19 +#endif -#define Z_STEP_PIN 56 // A2 -#define Z_DIR_PIN 60 // A6 -#define Z_ENABLE_PIN 55 // A1 -#define Z_MIN_PIN 18 -#define Z_MAX_PIN 19 +// +// Steppers +// +#define X_STEP_PIN 26 +#define X_DIR_PIN 27 +#define X_ENABLE_PIN 25 -#define E0_STEP_PIN 35 -#define E0_DIR_PIN 36 -#define E0_ENABLE_PIN 34 +#define Y_STEP_PIN 4 // A6 +#define Y_DIR_PIN 54 // A0 +#define Y_ENABLE_PIN 5 -#define E1_STEP_PIN 29 -#define E1_DIR_PIN 39 -#define E1_ENABLE_PIN 28 +#define Z_STEP_PIN 56 // A2 +#define Z_DIR_PIN 60 // A6 +#define Z_ENABLE_PIN 55 // A1 -#define E2_STEP_PIN 23 -#define E2_DIR_PIN 24 -#define E2_ENABLE_PIN 22 +#define E0_STEP_PIN 35 +#define E0_DIR_PIN 36 +#define E0_ENABLE_PIN 34 -#define SDSS 53 -#define LED_PIN 13 +#define E1_STEP_PIN 29 +#define E1_DIR_PIN 39 +#define E1_ENABLE_PIN 28 -#define FAN_PIN 7 -#define FAN2_PIN 6 -#define PS_ON_PIN 12 +#define E2_STEP_PIN 23 +#define E2_DIR_PIN 24 +#define E2_ENABLE_PIN 22 -#define HEATER_0_PIN 9 // EXTRUDER 1 +// +// Misc. Functions +// +#define SDSS 53 +#define LED_PIN 13 +#define PS_ON_PIN 12 + +// +// Temperature Sensors +// #if TEMP_SENSOR_0 == -1 - #define TEMP_0_PIN 4 // ANALOG NUMBERING + #define TEMP_0_PIN 4 // ANALOG NUMBERING #else - #define TEMP_0_PIN 13 // ANALOG NUMBERING + #define TEMP_0_PIN 13 // ANALOG NUMBERING #endif -#define HEATER_1_PIN 8 // EXTRUDER 2 #if TEMP_SENSOR_1 == -1 - #define TEMP_1_PIN 8 // ANALOG NUMBERING + #define TEMP_1_PIN 8 // ANALOG NUMBERING #else - #define TEMP_1_PIN 15 // ANALOG NUMBERING + #define TEMP_1_PIN 15 // ANALOG NUMBERING #endif -#define HEATER_BED_PIN 10 // BED #if TEMP_SENSOR_BED == -1 - #define TEMP_BED_PIN 8 // ANALOG NUMBERING + #define TEMP_BED_PIN 8 // ANALOG NUMBERING #else - #define TEMP_BED_PIN 14 // ANALOG NUMBERING + #define TEMP_BED_PIN 14 // ANALOG NUMBERING #endif -#define BEEPER_PIN 64 +// +// Heaters / Fans +// +#define HEATER_0_PIN 9 +#define HEATER_1_PIN 8 +#define HEATER_BED_PIN 10 -#define LCD_PINS_RS 14 -#define LCD_PINS_ENABLE 15 -#define LCD_PINS_D4 30 -#define LCD_PINS_D5 31 -#define LCD_PINS_D6 32 -#define LCD_PINS_D7 33 +#define FAN_PIN 7 +#define FAN1_PIN 6 + +// +// LCD / Controller +// +#define BEEPER_PIN 64 + +#define LCD_PINS_RS 14 +#define LCD_PINS_ENABLE 15 +#define LCD_PINS_D4 30 +#define LCD_PINS_D5 31 +#define LCD_PINS_D6 32 +#define LCD_PINS_D7 33 // Buttons are directly attached using keypad -#define BTN_EN1 61 -#define BTN_EN2 59 -#define BTN_ENC 43 +#define BTN_EN1 61 +#define BTN_EN2 59 +#define BTN_ENC 43 diff --git a/Marlin/pins_MEGATRONICS_3.h b/Marlin/pins_MEGATRONICS_3.h index a983ee2a7d..4035a78ab2 100644 --- a/Marlin/pins_MEGATRONICS_3.h +++ b/Marlin/pins_MEGATRONICS_3.h @@ -38,33 +38,45 @@ #define LARGE_FLASH true -#if ENABLED(Z_PROBE_SLED) - #define SLED_PIN -1 -#endif - -// Servo support +// +// Servos +// #define SERVO0_PIN 46 // AUX3-6 #define SERVO1_PIN 47 // AUX3-5 #define SERVO2_PIN 48 // AUX3-4 #define SERVO3_PIN 49 // AUX3-3 +// +// Limit Switches +// +#define X_MIN_PIN 37 +#define X_MAX_PIN 40 +#define Y_MIN_PIN 41 +#define Y_MAX_PIN 38 +#define Z_MIN_PIN 18 +#define Z_MAX_PIN 19 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 19 +#endif + +// +// Steppers +// #define X_STEP_PIN 58 #define X_DIR_PIN 57 #define X_ENABLE_PIN 59 -#define X_MIN_PIN 37 -#define X_MAX_PIN 40 -#define Y_STEP_PIN 5 +#define Y_STEP_PIN 5 #define Y_DIR_PIN 17 -#define Y_ENABLE_PIN 4 -#define Y_MIN_PIN 41 -#define Y_MAX_PIN 38 +#define Y_ENABLE_PIN 4 #define Z_STEP_PIN 16 #define Z_DIR_PIN 11 -#define Z_ENABLE_PIN 3 -#define Z_MIN_PIN 18 -#define Z_MAX_PIN 19 +#define Z_ENABLE_PIN 3 #define E0_STEP_PIN 28 #define E0_DIR_PIN 27 @@ -78,70 +90,80 @@ #define E2_DIR_PIN 60 #define E2_ENABLE_PIN 23 -#define SDSS 53 -#define LED_PIN 13 - -#define PS_ON_PIN 12 - -#define HEATER_0_PIN 2 -#define HEATER_1_PIN 9 -#define HEATER_2_PIN 8 -#define HEATER_BED_PIN 10 -#define FAN_PIN 6 -#define FAN2_PIN 7 +// +// Misc. Functions +// +#define SDSS 53 +#define LED_PIN 13 +#define PS_ON_PIN 12 +#define SLED_PIN -1 +// +// Temperature Sensors +// #if TEMP_SENSOR_0 == -1 - #define TEMP_0_PIN 11 // ANALOG NUMBERING + #define TEMP_0_PIN 11 // ANALOG NUMBERING #else - #define TEMP_0_PIN 15 // ANALOG NUMBERING + #define TEMP_0_PIN 15 // ANALOG NUMBERING #endif #if TEMP_SENSOR_1 == -1 - #define TEMP_1_PIN 10 // ANALOG NUMBERING + #define TEMP_1_PIN 10 // ANALOG NUMBERING #else - #define TEMP_1_PIN 13 // ANALOG NUMBERING + #define TEMP_1_PIN 13 // ANALOG NUMBERING #endif #if TEMP_SENSOR_2 == -1 - #define TEMP_2_PIN 9 // ANALOG NUMBERING + #define TEMP_2_PIN 9 // ANALOG NUMBERING #else - #define TEMP_2_PIN 12 // ANALOG NUMBERING + #define TEMP_2_PIN 12 // ANALOG NUMBERING #endif #if TEMP_SENSOR_BED == -1 - #define TEMP_BED_PIN 8 // ANALOG NUMBERING + #define TEMP_BED_PIN 8 // ANALOG NUMBERING #else - #define TEMP_BED_PIN 14 // ANALOG NUMBERING + #define TEMP_BED_PIN 14 // ANALOG NUMBERING #endif -/** - * Controllers and LCDs - */ -#define BEEPER_PIN 61 +// +// Heaters / Fans +// +#define HEATER_0_PIN 2 +#define HEATER_1_PIN 9 +#define HEATER_2_PIN 8 +#define HEATER_BED_PIN 10 -#define BTN_EN1 44 -#define BTN_EN2 45 -#define BTN_ENC 33 +#define FAN_PIN 6 +#define FAN1_PIN 7 + +// +// LCD / Controller +// +#define BEEPER_PIN 61 + +#define BTN_EN1 44 +#define BTN_EN2 45 +#define BTN_ENC 33 #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) - #define LCD_PINS_RS 56 // CS chip select / SS chip slave select - #define LCD_PINS_ENABLE 51 // SID (MOSI) - #define LCD_PINS_D4 52 // SCK (CLK) clock - #define SD_DETECT_PIN 35 + #define LCD_PINS_RS 56 // CS chip select / SS chip slave select + #define LCD_PINS_ENABLE 51 // SID (MOSI) + #define LCD_PINS_D4 52 // SCK (CLK) clock + #define SD_DETECT_PIN 35 #else - #define LCD_PINS_RS 32 - #define LCD_PINS_ENABLE 31 - #define LCD_PINS_D4 14 - #define LCD_PINS_D5 30 - #define LCD_PINS_D6 39 - #define LCD_PINS_D7 15 + #define LCD_PINS_RS 32 + #define LCD_PINS_ENABLE 31 + #define LCD_PINS_D4 14 + #define LCD_PINS_D5 30 + #define LCD_PINS_D6 39 + #define LCD_PINS_D7 15 - #define SHIFT_CLK 43 - #define SHIFT_LD 35 - #define SHIFT_OUT 34 - #define SHIFT_EN 44 + #define SHIFT_CLK 43 + #define SHIFT_LD 35 + #define SHIFT_OUT 34 + #define SHIFT_EN 44 #if ENABLED(MEGATRONICS_31) - #define SD_DETECT_PIN 56 + #define SD_DETECT_PIN 56 #else - #define SD_DETECT_PIN -1 + #define SD_DETECT_PIN -1 #endif #endif diff --git a/Marlin/pins_MINIRAMBO.h b/Marlin/pins_MINIRAMBO.h index 089ea59963..40b3afc781 100644 --- a/Marlin/pins_MINIRAMBO.h +++ b/Marlin/pins_MINIRAMBO.h @@ -31,52 +31,53 @@ #define BOARD_NAME "Mini Rambo" #define LARGE_FLASH true -#define X_STEP_PIN 37 -#define X_DIR_PIN 48 -#define X_MIN_PIN 12 -#define X_MAX_PIN 30 -#define X_ENABLE_PIN 29 -#define X_MS1_PIN 40 -#define X_MS2_PIN 41 +// +// Limit Switches +// +#define X_MIN_PIN 12 +#define X_MAX_PIN 30 +#define Y_MIN_PIN 11 +#define Y_MAX_PIN 24 +#define Z_MIN_PIN 10 +#define Z_MAX_PIN 23 -#define Y_STEP_PIN 36 -#define Y_DIR_PIN 49 -#define Y_MIN_PIN 11 -#define Y_MAX_PIN 24 -#define Y_ENABLE_PIN 28 -#define Y_MS1_PIN 69 -#define Y_MS2_PIN 39 - -#define Z_STEP_PIN 35 -#define Z_DIR_PIN 47 -#define Z_MIN_PIN 10 -#define Z_MAX_PIN 23 -#define Z_ENABLE_PIN 27 -#define Z_MS1_PIN 68 -#define Z_MS2_PIN 67 - -#define HEATER_BED_PIN 4 -#define TEMP_BED_PIN 2 - -#define HEATER_0_PIN 3 -#define TEMP_0_PIN 0 - -#define HEATER_1_PIN 7 -#define TEMP_1_PIN 1 - -#if ENABLED(BARICUDA) - #define HEATER_2_PIN 6 +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 23 #endif -#define E0_STEP_PIN 34 -#define E0_DIR_PIN 43 -#define E0_ENABLE_PIN 26 -#define E0_MS1_PIN 65 -#define E0_MS2_PIN 66 +// +// Steppers +// +#define X_STEP_PIN 37 +#define X_DIR_PIN 48 +#define X_ENABLE_PIN 29 +#define X_MS1_PIN 40 +#define X_MS2_PIN 41 -#define E1_STEP_PIN -1 -#define E1_DIR_PIN -1 -#define E1_ENABLE_PIN -1 +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 49 +#define Y_ENABLE_PIN 28 +#define Y_MS1_PIN 69 +#define Y_MS2_PIN 39 + +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_ENABLE_PIN 27 +#define Z_MS1_PIN 68 +#define Z_MS2_PIN 67 + +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 +#define E0_MS1_PIN 65 +#define E0_MS2_PIN 66 + +#define E1_STEP_PIN -1 +#define E1_DIR_PIN -1 +#define E1_ENABLE_PIN -1 #define MOTOR_CURRENT_PWM_XY_PIN 46 #define MOTOR_CURRENT_PWM_Z_PIN 45 @@ -84,33 +85,56 @@ //Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range #define MOTOR_CURRENT_PWM_RANGE 2000 #define DEFAULT_PWM_MOTOR_CURRENT {1300, 1300, 1250} -#define SDSS 53 -#define LED_PIN 13 -#define FAN_PIN 8 -#define FAN_1_PIN 6 +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 +#define TEMP_1_PIN 1 +#define TEMP_BED_PIN 2 + +// +// Heaters / Fans +// +#define HEATER_0_PIN 3 +#define HEATER_1_PIN 7 +#define HEATER_2_PIN 6 +#define HEATER_BED_PIN 4 + +#define FAN_PIN 8 +#define FAN1_PIN 6 + +// +// Misc. Functions +// +#define SDSS 53 +#define LED_PIN 13 + +// +// LCD / Controller +// #if ENABLED(ULTRA_LCD) - #define KILL_PIN 32 + #define KILL_PIN 32 #if ENABLED(NEWPANEL) // Beeper on AUX-4 - #define BEEPER_PIN 84 + #define BEEPER_PIN 84 - #define LCD_PINS_RS 82 + #define LCD_PINS_RS 82 #define LCD_PINS_ENABLE 18 - #define LCD_PINS_D4 19 - #define LCD_PINS_D5 70 - #define LCD_PINS_D6 85 - #define LCD_PINS_D7 71 + #define LCD_PINS_D4 19 + #define LCD_PINS_D5 70 + #define LCD_PINS_D6 85 + #define LCD_PINS_D7 71 //buttons are directly attached using AUX-2 - #define BTN_EN1 14 - #define BTN_EN2 72 - #define BTN_ENC 9 // the click + #define BTN_EN1 14 + #define BTN_EN2 72 + #define BTN_ENC 9 // the click - #define SD_DETECT_PIN 15 + #define SD_DETECT_PIN 15 #endif //NEWPANEL #endif //ULTRA_LCD diff --git a/Marlin/pins_MINITRONICS.h b/Marlin/pins_MINITRONICS.h index 34faa9ad31..ecd29d94da 100644 --- a/Marlin/pins_MINITRONICS.h +++ b/Marlin/pins_MINITRONICS.h @@ -28,82 +28,95 @@ #error "Oops! Make sure you have 'Minitronics' selected from the 'Tools -> Boards' menu." #endif +#if HOTENDS > 2 + #error "Minitronics supports up to 2 hotends. Comment this line to keep going." +#endif + #define BOARD_NAME "Minitronics v1.0 / v1.1" #define LARGE_FLASH true -#define X_STEP_PIN 48 -#define X_DIR_PIN 47 -#define X_ENABLE_PIN 49 -#define X_MIN_PIN 5 -#define X_MAX_PIN 2 +// +// Limit Switches +// +#define X_MIN_PIN 5 +#define X_MAX_PIN 2 +#define Y_MIN_PIN 2 +#define Y_MAX_PIN 15 +#define Z_MIN_PIN 6 +#define Z_MAX_PIN -1 -#define Y_STEP_PIN 39 // A6 -#define Y_DIR_PIN 40 // A0 -#define Y_ENABLE_PIN 38 -#define Y_MIN_PIN 2 -#define Y_MAX_PIN 15 +// +// Steppers +// +#define X_STEP_PIN 48 +#define X_DIR_PIN 47 +#define X_ENABLE_PIN 49 -#define Z_STEP_PIN 42 // A2 -#define Z_DIR_PIN 43 // A6 -#define Z_ENABLE_PIN 41 // A1 -#define Z_MIN_PIN 6 -#define Z_MAX_PIN -1 +#define Y_STEP_PIN 39 // A6 +#define Y_DIR_PIN 40 // A0 +#define Y_ENABLE_PIN 38 -#define E0_STEP_PIN 45 -#define E0_DIR_PIN 44 -#define E0_ENABLE_PIN 27 +#define Z_STEP_PIN 42 // A2 +#define Z_DIR_PIN 43 // A6 +#define Z_ENABLE_PIN 41 // A1 -#define E1_STEP_PIN 36 -#define E1_DIR_PIN 35 -#define E1_ENABLE_PIN 37 +#define E0_STEP_PIN 45 +#define E0_DIR_PIN 44 +#define E0_ENABLE_PIN 27 -#define E2_STEP_PIN -1 -#define E2_DIR_PIN -1 -#define E2_ENABLE_PIN -1 +#define E1_STEP_PIN 36 +#define E1_DIR_PIN 35 +#define E1_ENABLE_PIN 37 -#define SDSS 16 -#define LED_PIN 46 +// +// Temperature Sensors +// +#define SDSS 16 +#define LED_PIN 46 -#define FAN_PIN 9 +#define TEMP_0_PIN 7 // ANALOG NUMBERING +#define TEMP_1_PIN 6 // ANALOG NUMBERING +#define TEMP_BED_PIN 6 // ANALOG NUMBERING -#define TEMP_0_PIN 7 // ANALOG NUMBERING -#define TEMP_1_PIN 6 // ANALOG NUMBERING -#define TEMP_BED_PIN 6 // ANALOG NUMBERING +// +// Heaters / Fans +// +#define HEATER_0_PIN 7 // EXTRUDER 1 +#define HEATER_1_PIN 8 // EXTRUDER 2 +#define HEATER_BED_PIN 3 // BED -#define HEATER_0_PIN 7 // EXTRUDER 1 -#define HEATER_1_PIN 8 // EXTRUDER 2 -#define HEATER_BED_PIN 3 // BED +#define FAN_PIN 9 -/** - * Controllers and LCDs - */ -#define BEEPER_PIN -1 +// +// LCD / Controller +// +#define BEEPER_PIN -1 #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) - #define LCD_PINS_RS 15 // CS chip select /SS chip slave select - #define LCD_PINS_ENABLE 11 // SID (MOSI) - #define LCD_PINS_D4 10 // SCK (CLK) clock + #define LCD_PINS_RS 15 // CS chip select /SS chip slave select + #define LCD_PINS_ENABLE 11 // SID (MOSI) + #define LCD_PINS_D4 10 // SCK (CLK) clock - #define BTN_EN1 18 - #define BTN_EN2 17 - #define BTN_ENC 25 + #define BTN_EN1 18 + #define BTN_EN2 17 + #define BTN_ENC 25 - #define SD_DETECT_PIN 30 + #define SD_DETECT_PIN 30 #else - #define LCD_PINS_RS -1 - #define LCD_PINS_ENABLE -1 - #define LCD_PINS_D4 -1 - #define LCD_PINS_D5 -1 - #define LCD_PINS_D6 -1 - #define LCD_PINS_D7 -1 + #define LCD_PINS_RS -1 + #define LCD_PINS_ENABLE -1 + #define LCD_PINS_D4 -1 + #define LCD_PINS_D5 -1 + #define LCD_PINS_D6 -1 + #define LCD_PINS_D7 -1 // Buttons are directly attached using keypad - #define BTN_EN1 -1 - #define BTN_EN2 -1 - #define BTN_ENC -1 + #define BTN_EN1 -1 + #define BTN_EN2 -1 + #define BTN_ENC -1 - #define SD_DETECT_PIN -1 // Minitronics doesn't use this + #define SD_DETECT_PIN -1 // Minitronics doesn't use this #endif diff --git a/Marlin/pins_RAMBO.h b/Marlin/pins_RAMBO.h index 278774caf1..250a2fb155 100644 --- a/Marlin/pins_RAMBO.h +++ b/Marlin/pins_RAMBO.h @@ -32,85 +32,97 @@ #define LARGE_FLASH true -// Servo support -#define SERVO0_PIN 22 // Motor header MX1 -#define SERVO1_PIN 23 // Motor header MX2 -#define SERVO2_PIN 24 // Motor header MX3 -#define SERVO3_PIN 5 // PWM header pin 5 +// +// Servos +// +#define SERVO0_PIN 22 // Motor header MX1 +#define SERVO1_PIN 23 // Motor header MX2 +#define SERVO2_PIN 24 // Motor header MX3 +#define SERVO3_PIN 5 // PWM header pin 5 #if ENABLED(Z_PROBE_SLED) #define SLED_PIN -1 #endif -#define X_MIN_PIN 12 -#define X_MAX_PIN 24 -#define Y_MIN_PIN 11 -#define Y_MAX_PIN 23 -#define Z_MIN_PIN 10 -#define Z_MAX_PIN 30 +// +// Limit Switches +// +#define X_MIN_PIN 12 +#define X_MAX_PIN 24 +#define Y_MIN_PIN 11 +#define Y_MAX_PIN 23 +#define Z_MIN_PIN 10 +#define Z_MAX_PIN 30 + +// +// Z Probe (when not Z_MIN_PIN) +// #ifndef Z_MIN_PROBE_PIN - #define Z_MIN_PROBE_PIN 10 + #define Z_MIN_PROBE_PIN 30 #endif -#define X_STEP_PIN 37 -#define X_DIR_PIN 48 -#define X_ENABLE_PIN 29 -#define X_MS1_PIN 40 -#define X_MS2_PIN 41 +// +// Steppers +// +#define X_STEP_PIN 37 +#define X_DIR_PIN 48 +#define X_ENABLE_PIN 29 +#define X_MS1_PIN 40 +#define X_MS2_PIN 41 -#define Y_STEP_PIN 36 -#define Y_DIR_PIN 49 -#define Y_ENABLE_PIN 28 -#define Y_MS1_PIN 69 -#define Y_MS2_PIN 39 +#define Y_STEP_PIN 36 +#define Y_DIR_PIN 49 +#define Y_ENABLE_PIN 28 +#define Y_MS1_PIN 69 +#define Y_MS2_PIN 39 -#define Z_STEP_PIN 35 -#define Z_DIR_PIN 47 -#define Z_ENABLE_PIN 27 -#define Z_MS1_PIN 68 -#define Z_MS2_PIN 67 +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 47 +#define Z_ENABLE_PIN 27 +#define Z_MS1_PIN 68 +#define Z_MS2_PIN 67 -#define HEATER_BED_PIN 3 -#define TEMP_BED_PIN 2 +#define E0_STEP_PIN 34 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 26 +#define E0_MS1_PIN 65 +#define E0_MS2_PIN 66 -#define HEATER_0_PIN 9 -#define TEMP_0_PIN 0 +#define E1_STEP_PIN 33 +#define E1_DIR_PIN 42 +#define E1_ENABLE_PIN 25 +#define E1_MS1_PIN 63 +#define E1_MS2_PIN 64 -#define HEATER_1_PIN 7 -#define TEMP_1_PIN 1 - -#if ENABLED(BARICUDA) - #define HEATER_2_PIN 6 -#endif - -#define E0_STEP_PIN 34 -#define E0_DIR_PIN 43 -#define E0_ENABLE_PIN 26 -#define E0_MS1_PIN 65 -#define E0_MS2_PIN 66 - -#define E1_STEP_PIN 33 -#define E1_DIR_PIN 42 -#define E1_ENABLE_PIN 25 -#define E1_MS1_PIN 63 -#define E1_MS2_PIN 64 - -#define DIGIPOTSS_PIN 38 +#define DIGIPOTSS_PIN 38 #define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 +#define TEMP_1_PIN 1 +#define TEMP_BED_PIN 2 + +// +// Heaters / Fans +// +#define HEATER_0_PIN 9 +#define HEATER_1_PIN 7 +#define HEATER_2_PIN 6 +#define HEATER_BED_PIN 3 + +#define FAN_PIN 8 +#define FAN1_PIN 6 +#define FAN2_PIN 2 + +// +// Misc. Functions +// #define SDSS 53 #define LED_PIN 13 -#define FAN_PIN 8 - #define FILWIDTH_PIN 3 // ANALOG NUMBERING - -/********************************************************** - Fan Pins - Fan_0 8 - Fan_1 6 - Fan_2 2 -***********************************************************/ -#define PS_ON_PIN 4 +#define PS_ON_PIN 4 #if ENABLED(ULTRA_LCD) diff --git a/Marlin/pins_RAMPS.h b/Marlin/pins_RAMPS.h index 7e2acc21ec..8d5fb41c91 100644 --- a/Marlin/pins_RAMPS.h +++ b/Marlin/pins_RAMPS.h @@ -54,6 +54,9 @@ #define LARGE_FLASH true +// +// Servos +// #ifdef IS_RAMPS_13 #define SERVO0_PIN 7 // RAMPS_13 // Will conflict with BTN_EN2 on LCD_I2C_VIKI #else @@ -63,6 +66,9 @@ #define SERVO2_PIN 5 #define SERVO3_PIN 4 +// +// Limit Switches +// #define X_MIN_PIN 3 #ifndef X_MAX_PIN #define X_MAX_PIN 2 @@ -71,10 +77,17 @@ #define Y_MAX_PIN 15 #define Z_MIN_PIN 18 #define Z_MAX_PIN 19 + +// +// Z Probe (when not Z_MIN_PIN) +// #ifndef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN 32 #endif +// +// Steppers +// #define X_STEP_PIN 54 #define X_DIR_PIN 55 #define X_ENABLE_PIN 38 @@ -95,6 +108,16 @@ #define E1_DIR_PIN 34 #define E1_ENABLE_PIN 30 +// +// Temperature Sensors +// +#define TEMP_0_PIN 13 // ANALOG NUMBERING +#define TEMP_1_PIN 15 // ANALOG NUMBERING +#define TEMP_BED_PIN 14 // ANALOG NUMBERING + +// +// Misc. Functions +// #define SDSS 53 #define LED_PIN 13 @@ -105,15 +128,11 @@ #define FIL_RUNOUT_PIN 4 #define PS_ON_PIN 12 -#define TEMP_0_PIN 13 // ANALOG NUMBERING -#define TEMP_1_PIN 15 // ANALOG NUMBERING -#define TEMP_BED_PIN 14 // ANALOG NUMBERING - -#if ENABLED(Z_PROBE_SLED) - #define SLED_PIN -1 -#endif +#define SLED_PIN -1 +// // Augmentation for auto-assigning RAMPS plugs +// #if DISABLED(IS_RAMPS_EEB) && DISABLED(IS_RAMPS_EEF) && DISABLED(IS_RAMPS_EFB) && DISABLED(IS_RAMPS_EFF) && DISABLED(IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) #if HOTENDS > 1 #if TEMP_SENSOR_BED @@ -128,10 +147,9 @@ #endif #endif -/** - * Hi Voltage PWM Pin Assignments - */ - +// +// Heaters / Fans +// #ifndef MOSFET_D_PIN #define MOSFET_D_PIN -1 #endif @@ -175,10 +193,9 @@ #define FAN_PIN 4 // IO pin. Buffer needed #endif -/** - * LCD Controller Pin Assignments - */ - +// +// LCD / Controller +// #if ENABLED(ULTRA_LCD) #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) diff --git a/Marlin/pins_RAMPS_OLD.h b/Marlin/pins_RAMPS_OLD.h index 213bd3f1e8..238e484c65 100644 --- a/Marlin/pins_RAMPS_OLD.h +++ b/Marlin/pins_RAMPS_OLD.h @@ -33,45 +33,68 @@ // Uncomment the following line for RAMPS v1.0 //#define RAMPS_V_1_0 +// +// Limit Switches +// +#define X_MIN_PIN 3 +#define X_MAX_PIN 2 +#define Y_MIN_PIN 16 +#define Y_MAX_PIN 17 +#define Z_MIN_PIN 18 +#define Z_MAX_PIN 19 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 19 +#endif + +// +// Steppers +// #define X_STEP_PIN 26 #define X_DIR_PIN 28 #define X_ENABLE_PIN 24 -#define X_MIN_PIN 3 -#define X_MAX_PIN 2 #define Y_STEP_PIN 38 #define Y_DIR_PIN 40 #define Y_ENABLE_PIN 36 -#define Y_MIN_PIN 16 -#define Y_MAX_PIN 17 #define Z_STEP_PIN 44 #define Z_DIR_PIN 46 #define Z_ENABLE_PIN 42 -#define Z_MIN_PIN 18 -#define Z_MAX_PIN 19 #define E0_STEP_PIN 32 #define E0_DIR_PIN 34 #define E0_ENABLE_PIN 30 +// +// Misc. Functions +// #define SDPOWER 48 #define SDSS 53 #define LED_PIN 13 -#if ENABLED(RAMPS_V_1_0) // RAMPS_V_1_0 - #define HEATER_0_PIN 12 // RAMPS 1.0 - #define HEATER_BED_PIN -1 // RAMPS 1.0 - #define FAN_PIN 11 // RAMPS 1.0 -#else // RAMPS_V_1_1 or RAMPS_V_1_2 - #define HEATER_0_PIN 10 // RAMPS 1.1 - #define HEATER_BED_PIN 8 // RAMPS 1.1 - #define FAN_PIN 9 // RAMPS 1.1 -#endif - +// +// Temperature Sensors +// #define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! +// +// Heaters / Fans +// +#if ENABLED(RAMPS_V_1_0) + #define HEATER_0_PIN 12 + #define HEATER_BED_PIN -1 + #define FAN_PIN 11 +#else // RAMPS_V_1_1 or RAMPS_V_1_2 + #define HEATER_0_PIN 10 + #define HEATER_BED_PIN 8 + #define FAN_PIN 9 +#endif + // SPI for Max6675 or Max31855 Thermocouple #if DISABLED(SDSUPPORT) #define MAX6675_SS 66// Do not use pin 53 if there is even the remote possibility of using Display/SD card diff --git a/Marlin/pins_RUMBA.h b/Marlin/pins_RUMBA.h index ec5e0236e6..3c0e945d54 100644 --- a/Marlin/pins_RUMBA.h +++ b/Marlin/pins_RUMBA.h @@ -35,27 +35,37 @@ #define DEFAULT_MACHINE_NAME "Rumba" #define BOARD_NAME "Rumba" +// +// Limit Switches +// +#define X_MIN_PIN 37 +#define X_MAX_PIN 36 +#define Y_MIN_PIN 35 +#define Y_MAX_PIN 34 +#define Z_MIN_PIN 33 +#define Z_MAX_PIN 32 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 32 +#endif + +// +// Steppers +// #define X_STEP_PIN 17 #define X_DIR_PIN 16 #define X_ENABLE_PIN 48 -#define X_MIN_PIN 37 -#define X_MAX_PIN 36 #define Y_STEP_PIN 54 #define Y_DIR_PIN 47 #define Y_ENABLE_PIN 55 -#define Y_MIN_PIN 35 -#define Y_MAX_PIN 34 #define Z_STEP_PIN 57 #define Z_DIR_PIN 56 #define Z_ENABLE_PIN 62 -#define Z_MIN_PIN 33 -#define Z_MAX_PIN 32 - -#ifndef Z_MIN_PROBE_PIN - #define Z_MIN_PROBE_PIN 33 -#endif #define E0_STEP_PIN 23 #define E0_DIR_PIN 22 @@ -69,18 +79,17 @@ #define E2_DIR_PIN 28 #define E2_ENABLE_PIN 39 +// +// Misc. Functions +// #define LED_PIN 13 -#define FAN_PIN 7 -#define FAN1_PIN 8 - #define PS_ON_PIN 45 #define KILL_PIN 46 -#define HEATER_0_PIN 2 // EXTRUDER 1 -#define HEATER_1_PIN 3 // EXTRUDER 2 -#define HEATER_2_PIN 6 // EXTRUDER 3 - +// +// Temperature Sensors +// #if TEMP_SENSOR_0 == -1 #define TEMP_0_PIN 6 // ANALOG NUMBERING - connector *K1* on RUMBA thermocouple ADD ON is used #else @@ -99,10 +108,21 @@ #define TEMP_2_PIN 13 // ANALOG NUMBERING - default connector for thermistor *T2* on rumba board is used #endif -//optional for extruder 4 or chamber: #define TEMP_X_PIN 12 // ANALOG NUMBERING - default connector for thermistor *T3* on rumba board is used -//optional FAN1 can be used as 4th heater output: #define HEATER_3_PIN 8 // EXTRUDER 4 +// +// Heaters / Fans +// +#define HEATER_0_PIN 2 +#define HEATER_1_PIN 3 +#define HEATER_2_PIN 6 +#define HEATER_3_PIN 8 +#define HEATER_BED_PIN 9 + +#define FAN_PIN 7 +#define FAN1_PIN 8 + +//optional for extruder 4 or chamber: +// #define TEMP_X_PIN 12 // ANALOG NUMBERING - default connector for thermistor *T3* on rumba board is used -#define HEATER_BED_PIN 9 // BED #if TEMP_SENSOR_BED == -1 #define TEMP_BED_PIN 7 // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple #else diff --git a/Marlin/pins_SETHI.h b/Marlin/pins_SETHI.h index ff154acf54..a710e1bf35 100644 --- a/Marlin/pins_SETHI.h +++ b/Marlin/pins_SETHI.h @@ -34,53 +34,62 @@ #define GEN7_VERSION 12 // v1.x #endif -//x axis pins -#define X_STEP_PIN 19 -#define X_DIR_PIN 18 -#define X_ENABLE_PIN 24 -#define X_STOP_PIN 2 +// +// Limit Switches +// +#define X_STOP_PIN 2 +#define Y_STOP_PIN 0 +#define Z_MIN_PIN 1 +#define Z_MAX_PIN 0 -//y axis pins -#define Y_STEP_PIN 23 -#define Y_DIR_PIN 22 -#define Y_ENABLE_PIN 24 -#define Y_STOP_PIN 0 +// +// Steppers +// +#define X_STEP_PIN 19 +#define X_DIR_PIN 18 +#define X_ENABLE_PIN 24 -//z axis pins -#define Z_STEP_PIN 26 -#define Z_DIR_PIN 25 -#define Z_ENABLE_PIN 24 -#define Z_MIN_PIN 1 -#define Z_MAX_PIN 0 +#define Y_STEP_PIN 23 +#define Y_DIR_PIN 22 +#define Y_ENABLE_PIN 24 -//extruder pins -#define E0_STEP_PIN 28 -#define E0_DIR_PIN 27 -#define E0_ENABLE_PIN 24 +#define Z_STEP_PIN 26 +#define Z_DIR_PIN 25 +#define Z_ENABLE_PIN 24 -#define TEMP_0_PIN 1 -#define TEMP_BED_PIN 2 +#define E0_STEP_PIN 28 +#define E0_DIR_PIN 27 +#define E0_ENABLE_PIN 24 -#define HEATER_0_PIN 4 -#define HEATER_BED_PIN 3 +// +// Temperature Sensors +// +#define TEMP_0_PIN 1 +#define TEMP_BED_PIN 2 + +// +// Heaters / Fans +// +#define HEATER_0_PIN 4 +#define HEATER_BED_PIN 3 #if (GEN7_VERSION >= 13) // Gen7 v1.3 removed the fan pin - #define FAN_PIN -1 + #define FAN_PIN -1 #else - #define FAN_PIN 31 + #define FAN_PIN 31 #endif -#define PS_ON_PIN 15 +#define PS_ON_PIN 15 //All these generations of Gen7 supply thermistor power //via PS_ON, so ignore bad thermistor readings #define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE //our pin for debugging. -#define DEBUG_PIN 0 +#define DEBUG_PIN 0 //our RS485 pins -#define TX_ENABLE_PIN 12 -#define RX_ENABLE_PIN 13 +#define TX_ENABLE_PIN 12 +#define RX_ENABLE_PIN 13 diff --git a/Marlin/pins_ULTIMAIN_2.h b/Marlin/pins_ULTIMAIN_2.h index c2de0a426a..e1b0ecea02 100644 --- a/Marlin/pins_ULTIMAIN_2.h +++ b/Marlin/pins_ULTIMAIN_2.h @@ -32,43 +32,35 @@ #define DEFAULT_SOURCE_CODE_URL "https://github.com/Ultimaker/Marlin" #define BOARD_NAME "Ultimaker 2.x" -#define X_STEP_PIN 25 -#define X_DIR_PIN 23 -#define X_STOP_PIN 22 -#define X_ENABLE_PIN 27 +// +// Limit Switches +// +#define X_STOP_PIN 22 +#define Y_STOP_PIN 26 +#define Z_STOP_PIN 29 -#define Y_STEP_PIN 32 -#define Y_DIR_PIN 33 -#define Y_STOP_PIN 26 -#define Y_ENABLE_PIN 31 +// +// Steppers +// +#define X_STEP_PIN 25 +#define X_DIR_PIN 23 +#define X_ENABLE_PIN 27 -#define Z_STEP_PIN 35 -#define Z_DIR_PIN 36 -#define Z_STOP_PIN 29 -#define Z_ENABLE_PIN 34 +#define Y_STEP_PIN 32 +#define Y_DIR_PIN 33 +#define Y_ENABLE_PIN 31 -#define HEATER_BED_PIN 4 -#define TEMP_BED_PIN 10 +#define Z_STEP_PIN 35 +#define Z_DIR_PIN 36 +#define Z_ENABLE_PIN 34 -#define HEATER_0_PIN 2 -#define TEMP_0_PIN 8 +#define E0_STEP_PIN 42 +#define E0_DIR_PIN 43 +#define E0_ENABLE_PIN 37 -#define HEATER_1_PIN 3 -#define TEMP_1_PIN 9 - -#define E0_STEP_PIN 42 -#define E0_DIR_PIN 43 -#define E0_ENABLE_PIN 37 - -#define E1_STEP_PIN 49 -#define E1_DIR_PIN 47 -#define E1_ENABLE_PIN 48 - -#define SDSS 53 -#define LED_PIN 8 -#define FAN_PIN 7 -#define SAFETY_TRIGGERED_PIN 28 //PIN to detect the safety circuit has triggered -#define MAIN_VOLTAGE_MEASURE_PIN 14 //Analogue PIN to measure the main voltage, with a 100k - 4k7 resitor divider. +#define E1_STEP_PIN 49 +#define E1_DIR_PIN 47 +#define E1_ENABLE_PIN 48 #define MOTOR_CURRENT_PWM_XY_PIN 44 #define MOTOR_CURRENT_PWM_Z_PIN 45 @@ -77,18 +69,42 @@ #define MOTOR_CURRENT_PWM_RANGE 2000 #define DEFAULT_PWM_MOTOR_CURRENT {1300, 1300, 1250} -#define BEEPER_PIN 18 +// +// Temperature Sensors +// +#define TEMP_0_PIN 8 +#define TEMP_1_PIN 9 +#define TEMP_BED_PIN 10 -#define LCD_PINS_RS 20 -#define LCD_PINS_ENABLE 15 -#define LCD_PINS_D4 14 -#define LCD_PINS_D5 21 -#define LCD_PINS_D6 5 -#define LCD_PINS_D7 6 +// +// Heaters / Fans +// +#define HEATER_0_PIN 2 +#define HEATER_1_PIN 3 +#define HEATER_BED_PIN 4 -//buttons are directly attached -#define BTN_EN1 40 -#define BTN_EN2 41 -#define BTN_ENC 19 +#define FAN_PIN 7 -#define SD_DETECT_PIN 39 +// +// SD Card +// +#define SDSS 53 +#define SD_DETECT_PIN 39 + +#define LED_PIN 8 +#define SAFETY_TRIGGERED_PIN 28 // PIN to detect the safety circuit has triggered +#define MAIN_VOLTAGE_MEASURE_PIN 14 // ANALOG PIN to measure the main voltage, with a 100k - 4k7 resitor divider. + +#define BEEPER_PIN 18 + +#define LCD_PINS_RS 20 +#define LCD_PINS_ENABLE 15 +#define LCD_PINS_D4 14 +#define LCD_PINS_D5 21 +#define LCD_PINS_D6 5 +#define LCD_PINS_D7 6 + +// Buttons are directly attached +#define BTN_EN1 40 +#define BTN_EN2 41 +#define BTN_ENC 19 diff --git a/Marlin/pins_ULTIMAKER.h b/Marlin/pins_ULTIMAKER.h index d770f3a612..f7ad15ef7e 100644 --- a/Marlin/pins_ULTIMAKER.h +++ b/Marlin/pins_ULTIMAKER.h @@ -34,49 +34,74 @@ #define LARGE_FLASH true -#define SERVO0_PIN 13 // untested +// +// Servos +// +#define SERVO0_PIN 13 // untested -#define X_STEP_PIN 25 -#define X_DIR_PIN 23 -#define X_MIN_PIN 22 -#define X_MAX_PIN 24 -#define X_ENABLE_PIN 27 +// +// Limit Switches +// +#define X_MIN_PIN 22 +#define X_MAX_PIN 24 +#define Y_MIN_PIN 26 +#define Y_MAX_PIN 28 +#define Z_MIN_PIN 30 +#define Z_MAX_PIN 32 -#define Y_STEP_PIN 31 -#define Y_DIR_PIN 33 -#define Y_MIN_PIN 26 -#define Y_MAX_PIN 28 -#define Y_ENABLE_PIN 29 +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 32 +#endif -#define Z_STEP_PIN 37 -#define Z_DIR_PIN 39 -#define Z_MIN_PIN 30 -#define Z_MAX_PIN 32 -#define Z_ENABLE_PIN 35 +// +// Steppers +// +#define X_STEP_PIN 25 +#define X_DIR_PIN 23 +#define X_ENABLE_PIN 27 -#define HEATER_BED_PIN 4 -#define TEMP_BED_PIN 10 +#define Y_STEP_PIN 31 +#define Y_DIR_PIN 33 +#define Y_ENABLE_PIN 29 -#define HEATER_0_PIN 2 -#define TEMP_0_PIN 8 +#define Z_STEP_PIN 37 +#define Z_DIR_PIN 39 +#define Z_ENABLE_PIN 35 -#define HEATER_1_PIN 3 -#define TEMP_1_PIN 9 +#define E0_STEP_PIN 43 +#define E0_DIR_PIN 45 +#define E0_ENABLE_PIN 41 -#define E0_STEP_PIN 43 -#define E0_DIR_PIN 45 -#define E0_ENABLE_PIN 41 +#define E1_STEP_PIN 49 +#define E1_DIR_PIN 47 +#define E1_ENABLE_PIN 48 -#define E1_STEP_PIN 49 -#define E1_DIR_PIN 47 -#define E1_ENABLE_PIN 48 +// +// Temperature Sensors +// +#define TEMP_0_PIN 8 +#define TEMP_1_PIN 9 +#define TEMP_BED_PIN 10 + +// +// Heaters / Fans +// +#define HEATER_0_PIN 2 +#define HEATER_1_PIN 3 +#define HEATER_BED_PIN 4 #define SDSS 53 #define LED_PIN 13 -#define FAN_PIN 7 +#define FAN_PIN 7 #define PS_ON_PIN 12 #define SUICIDE_PIN 54 //PIN that has to be turned on right after start, to keep power flowing. +// +// LCD / Controller +// #if ENABLED(ULTRA_LCD) #define BEEPER_PIN 18 diff --git a/Marlin/pins_ULTIMAKER_OLD.h b/Marlin/pins_ULTIMAKER_OLD.h index 33bc26c9aa..cb0f763198 100644 --- a/Marlin/pins_ULTIMAKER_OLD.h +++ b/Marlin/pins_ULTIMAKER_OLD.h @@ -34,41 +34,64 @@ #define LARGE_FLASH true -#define X_STEP_PIN 25 -#define X_DIR_PIN 23 -#define X_MIN_PIN 15 -#define X_MAX_PIN 14 -#define X_ENABLE_PIN 27 +// +// Limit Switches +// +#define X_MIN_PIN 15 +#define X_MAX_PIN 14 +#define Y_MIN_PIN 17 +#define Y_MAX_PIN 16 +#define Z_MIN_PIN 19 +#define Z_MAX_PIN 18 -#define Y_STEP_PIN 31 -#define Y_DIR_PIN 33 -#define Y_MIN_PIN 17 -#define Y_MAX_PIN 16 -#define Y_ENABLE_PIN 29 +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 18 +#endif -#define Z_STEP_PIN 37 -#define Z_DIR_PIN 39 -#define Z_MIN_PIN 19 -#define Z_MAX_PIN 18 -#define Z_ENABLE_PIN 35 +// +// Steppers +// +#define X_STEP_PIN 25 +#define X_DIR_PIN 23 +#define X_ENABLE_PIN 27 -#define TEMP_0_PIN 8 -#define TEMP_1_PIN 1 +#define Y_STEP_PIN 31 +#define Y_DIR_PIN 33 +#define Y_ENABLE_PIN 29 -#define HEATER_0_PIN 2 -#define HEATER_1_PIN 1 +#define Z_STEP_PIN 37 +#define Z_DIR_PIN 39 +#define Z_ENABLE_PIN 35 -#define E0_STEP_PIN 43 -#define E0_DIR_PIN 45 -#define E0_ENABLE_PIN 41 +#define E0_STEP_PIN 43 +#define E0_DIR_PIN 45 +#define E0_ENABLE_PIN 41 -#define E1_STEP_PIN -1 -#define E1_DIR_PIN -1 -#define E1_ENABLE_PIN -1 +#define E1_STEP_PIN -1 +#define E1_DIR_PIN -1 +#define E1_ENABLE_PIN -1 -#define LCD_PINS_RS 24 -#define LCD_PINS_ENABLE 22 -#define LCD_PINS_D4 36 -#define LCD_PINS_D5 34 -#define LCD_PINS_D6 32 -#define LCD_PINS_D7 30 +// +// Temperature Sensors +// +#define TEMP_0_PIN 8 +#define TEMP_1_PIN 1 + +// +// Heaters / Fans +// +#define HEATER_0_PIN 2 +#define HEATER_1_PIN 1 + +// +// LCD / Controller +// +#define LCD_PINS_RS 24 +#define LCD_PINS_ENABLE 22 +#define LCD_PINS_D4 36 +#define LCD_PINS_D5 34 +#define LCD_PINS_D6 32 +#define LCD_PINS_D7 30